Master Prep
™
QB900NZ 30
QB900NZ_30_120626_1.indd 1 12-06-26 12:58 PM
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
WHEN USING ELECTRICAL
APPLIANCES, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE
USING YOUR NINJA™ MASTER
PREP™.
2
IMPORTANT: This appliance
can be used by children aged from
8 years and above and persons
with reduced physical, sensory
or mental capabilities or lack
of experience and knowledge if
they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children should be supervised to
ensure that they do not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
1. Close supervision is necessary
when any appliance is used by or
near children.
2. To protect against electric shock,
DO NOT immerse cord, plug or
any part of the main unit in water
or any other liquids.
3. DO NOT let cord hang over edge
of table or counter, or touch hot
surfaces.
4. DO NOT operate the appliance
with a damaged plug or cord,
or if the unit has been dropped,
damaged or dropped in water. To
avoid the risk of electric shock,
do not disassemble or attempt to
repair the appliance on your own.
If the supply cord is damaged, it
must be replaced by a qualified
electrician in order to avoid a
hazard. Incorrect re-assembly or
repair can cause a risk of electrical
shock or injury to persons when
the appliance is usedt.
5. Unplug appliance from outlet
when not in use and before
cleaning.
6. DO NOT place on or near a hot
gas or electric burner.
7. The use of accessory
attachments, including canning
jars not recommended by the
manufacturer may cause fire,
electrical shock or risk of personal
injury.
8. Extreme caution must be used
when moving an appliance
containing hot food, water or
other liquids.
QB900NZ_30_120626_1.indd 2 12-06-26 12:58 PM
3
23. DO NOT operate the appliance
empty.
24. If the appliance overheats, a
thermal switch will become
activated and shut off the motor.
To reset, unplug the appliance and
let it cool down for approximately
10 minutes before using again.
25. THIS PRODUCT IS INTENDED
FOR HOUSEHOLD USE ONLY.
Do not use this appliance for
anything other than its intended
use. Do not use outdoors.
WARNING: Extension
cords are not recommended for use
with this product.
SAVE THESE
INSTRUCTIONS
9. Use this appliance on a stable
work surface away from water.
10. DO NOT remove the motor head
before the chopping blades have
stopped turning.
11. CAUTION! Chopping blades are
sharp, handle with care. When
handling the chopping blades,
always hold by the plastic shaft.
12. DO NOT attempt to sharpen
blades.
13. DO NOT expose pitcher to
extreme temperature changes.
14. DO NOT use pitcher if it is cracked
or chipped.
15. DO NOT use the appliance if
chopping blades are bent or
damaged.
16. Avoid contact with moving parts
at all times. Keep hands, hair,
clothing as well as spatulas and
other utensils away from pitcher
during operation to prevent risk of
personal injury and/or damage to
the appliance.
17. Exercise extreme caution when
blending hot liquids.
18. Immediately release the On/Off
pulse button on the motor head
in the event that the appliance
malfunctions during use.
19. To reduce the risk of injury, NEVER
operate the appliance without the
splash guard in place; DO NOT try
to defeat the interlock mechanism;
make sure that the cutting blades
are properly assembled before
operating the appliance.
20. DO NOT use outdoors.
21. DO NOT use appliance for other
than intended use.
22. DO NOT operate the appliance for
more than 15 seconds.
QB900NZ_30_120626_1.indd 3 12-06-26 12:58 PM
4
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50Hz.
Power: 400 Watts
Pitcher Capacity: 1.5 L (48 ounces) (6 cups)
Bowl Capacity: 0.5 L (16 ounces) (2 cups)
Z854
SAA110120EA
QB900NZ_30_120626_1.indd 4 12-06-26 12:58 PM
Contents
Getting Started ......................................................................6
Using the Master Prep™ Pitcher .......................................8
Using the Master Prep™ Bowl ...........................................10
Cleaning and Maintenance ................................................12
Troubleshooting Guide .......................................................12
Thank you for
purchasing
the Ninja™
Master Prep™.
5
QB900NZ_30_120626_1.indd 5 12-06-26 12:58 PM
6
j Pitcher Storage Lid
k Pouring Spout
l Pitcher Splash Guard
m Upper Blade (pitcher)
n Lower Blade (pitcher)
o Master Prep™ Pitcher
p Spindle Pin
q Non-Slip Base Gasket (pitcher)
r Power Cord (not shown)
a Bowl Splash Guard
b Upper Blade (bowl)
c Lower Blade (bowl)
d Master Prep™ Bowl
e Spindle Pin
f Non-Slip Base Gasket (bowl)
g On/Off Pulse Button
h Power Head
i Bowl Storage Lid
Getting Started
b
a
d
g
e
h
i
j
m
l
k
n
o
c
p
f
q
QB900NZ_30_120626_1.indd 6 12-06-26 12:58 PM
7
400 Watt Power Head
The 400 watt power head operates on 220-240V~, 50Hz electrical power. NEVER
allow the power head to become wet when plugged into an electrical outlet.
WAR NING: The power head should never be immersed in water or any other liquid.
CAUTION: Make sure that the power head is unplugged from the electrical outlet and
that the blades have stopped turning before attaching or removing any accessory.
CAUTION: Blades are sharp! Use extreme caution when handling the blades.
Always hold them by the shaft. Do not
attempt to sharpen blades.
IMPORTANT: Never run the appliance empty.
The Ninja™ Master Prep™ is an indispensable kitchen tool that is perfect for blending,
chopping, mixing or pureeing when preparing your favorite recipes. For best results,
be sure to carefully read all the instructions contained in the manual before using this
appliance.
QB900NZ_30_120626_1.indd 7 12-06-26 12:58 PM
1
8
Using the Master Prep™ Pitcher
2
WAR NING: DO NOT try to place the
blades onto the power head and then
into the Master Prep™ pitcher.
Shaft
CAUTION: Blades are sharp! Use
extreme caution when handling the
blades. Always hold them by the shaft.
IMPORTANT: Never run the appliance
empt y.
1 Place the Master Prep™ pitcher on a
clean, dry, level surface.
2 Holding the lower blade by the shaft,
place it onto the spindle pin inside the
Master Prep™ pitcher. (Fig. 1)
3 Carefully insert the upper blade over
the lower blade rotating it until it locks
onto the lower blade. (Fig. 2)
IMPORTANT: Always assemble the
blades inside the container.
QB900NZ_30_120626_1.indd 8 12-06-26 12:58 PM
9
Pouring Spout
3
5
4 Add the ingredients to be processed
into the Master Prep™ pitcher.
IMPORTANT: The blade assembly for
the Master Prep™ pitcher must always
be in place before ingredients are
added.
5 Place the pitcher splash guard onto the
top of the Master Prep™ pitcher. (Fig. 3)
6 Place the power head on top of the
pitcher splash guard making sure that
it is securely in place. (Fig. 4) DO
NOT attempt to operate the appliance
without the safety splash guard in
place.
7 To start the appliance, plug the power
cord into the electrical outlet, securely
hold power head while operating
and press on the on/off pulse button
located on the top of the power head.
(Fig. 5)
8 Hold the Master Prep™ pitcher firmly
while depressing the on/off pulse
button to ensure the unit stays in place.
NOTE: DO NOT operate the appliance
continuously for more than 15 seconds
at a time.
9 To stop the appliance, remove your
fingers from the on/off pulse button.
10 In order to obtain a better quality of
chopping, operate the appliance by
using the “Pulse” method.
11 Make sure that the blades have
stopped completely before removing
the power head.
12 If the ingredients stick to the side of
the Master Prep™ pitcher, stop the
appliance, remove the power head
and the splash guard. Use a spatula to
dislodge the pieces and then replace
the splash guard and the power head.
Continue processing.
13 Depending on the consistency of the
contents, use the pouring spout to
empty liquid contents.
14 For thicker consistencies, first remove
splash guard and blade assembly (by
its shaft), then empty contents of the
Master Prep™ pitcher.
4
QB900NZ_30_120626_1.indd 9 12-06-26 12:58 PM
2
10
Using the Master Prep™ Bowl
Shaft
CAUTION: Blades are sharp! Use
extreme caution when handling the
blades. Always hold them by the shaft.
IMPORTANT: Never run the appliance
empt y.
1 Place the Master Prep™ bowl on a
clean, dry, level surface.
2 Holding the lower blade by the shaft,
place it over the spindle pin inside the
Master Prep™ bowl. (Fig. 1)
3 Carefully insert the upper blade over
the lower blade rotating it until it locks
onto the lower blade. (Fig. 2)
IMPORTANT: Always assemble the
blades inside the container.
WAR NING: DO NOT try to place the
blades onto the power head and then
into the Master Prep™ bowl.
4 Place the food that you want to process
into the Master Prep™ bowl.
IMPORTANT: The blade assembly for
the Master Prep™ bowl must always be
in place before ingredients are added.
NOTE: DO NOT add more than 2 cups
dry or 1 cup liquid ingredients as this
will strain the motor and may cause
overflow.
1
QB900NZ_30_120626_1.indd 10 12-06-26 12:58 PM
11
5
10 In order to obtain a better quality of
chopping, operate the appliance by
using the “pulse” method.
11 Make sure that the blades have
stopped completely before removing
the power head.
12 If the ingredients stick to the side
of the Master Prep™ bowl, stop the
appliance, remove the power head
and the splash guard. Use a spatula to
dislodge the pieces and then replace
the splash guard and the power head.
Continue processing.
13 Remove the blade assembly by its shaft
before you empty the contents of the
Master Prep™ bowl.
HINTS & TIPS
• The double chopping blades can be used
for chopping meat, fish, vegetables,
cheese etc.
• For finer chopping, increase the length of
time you process.
• For coarse chopping, use the pulse
button for a few seconds and monitor
food texture.
• Pre-cut larger pieces to make them
fit into the Master Prep™ bowl. When
chopping hard foods (e.g. meat, cheese)
cut into 2-3 cm cubes.
5 Place the splash guard on the bowl.
(Fig. 3)
6 Place the power head on top of the
splash guard making sure that it is
securely in place. (Fig. 4) DO NOT
attempt to operate the appliance
without the safety splash guard in
place.
7 To start the appliance, plug the power
cord into the electrical outlet, securely
hold power head while operating
and press on the on/off pulse button
located on the top of the power head.
(Fig. 5)
8 Hold the Master Prep™ bowl firmly
while depressing the on/off pulse
button to ensure the unit stays in place.
NOTE: DO NOT operate the appliance
continuously for more than 15 seconds
at a time. Be careful not to over
process. For coarsely chopped foods,
use repeated short pulsing action until
the desired consistency is reached.
9 To stop the appliance, remove your
fingers from the on/off pulse button.
3
4
QB900NZ_30_120626_1.indd 11 12-06-26 12:58 PM
12
Cleaning and Maintenance
CAUTION: Make sure that the power head is unplugged from power source before
inserting or removing any attachment and before cleaning.
DO NOT immerse the power head into water or any other liquid. Clean with a damp
sponge or cloth and wipe dry.
The Master Prep™ pitcher, Master Prep™ bowl, storage lids, Master Prep™ splash
guards and chopping blades are all dishwasher safe. It is recommended to place the
storage lids and the chopping blades on the top rack. Use extreme caution when
handling the chopping blades as they are very sharp.
PROBLEMS POSSIBLE REASONS & SOLUTIONS
Motor Doesn’t Start
or Blades Don’t
Rotate.
Check that the bottom of motor head is clean and
there is no food blocking connection when placing
on containers.
There is too much food in the container.
The unit has overheated. Unplug and wait
approximately 10 minutes before using again.
Make sure the splash guard is securely on container.
Make sure the power head is securely placed on
splash guard.
Check that the plug is securely inserted into the
electrical outlet.
Food is Unevenly
Chopped.
Either you are chopping too much food at one
time, or the pieces are not small enough. Try
cutting the food into smaller pieces of even size
and processing smaller amounts per batch.
Food is Chopped Too
Fine or is Too
Watery.
The food has been over processed. Use brief
pulses or process for shorter time. Let blades
stop completely between pulses.
Food Collects on
Splash Guard/Safety
Cover or on the Sides
of the Master Prep™
Pitcher or Master
Prep™ Bowl.
You may be processing too much food. Turn the
machine off. When the blades stop rotating,
remove the power head and the splash guard.
Remove some of the food being processed.
You Cannot Achieve
Snow From Solid Ice
Do not use ice that has been sitting out or has
started to melt. Be sure to use short pulses in
the beginning to break up large pieces.
Troubleshooting Guide
QB900NZ_30_120626_1.indd 12 12-06-26 12:58 PM
13
ONE (1) YEAR
LIMITED REPLACEMENT WARRANTY STATEMENT
If your product becomes defective due to faulty material or workmanship within a period of 1 year from the date of
purchase, we warrant to do the following:
• For New Zealand Consumers: We will replace the product with a new product, free of charge, or repair the
product at our cost, at our discretion.
• For Australian Consumers: Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Your warranty is subject to the following conditions:
• DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped, damaged or
dropped in water. To avoid the risk of electric shock, do not disassemble or attempt to repair the appliance on
your own. If the supply cord is damaged, it must be replaced by a qualified electrician in order
to avoid a hazard. Incorrect re-assembly or repair can cause a risk of electrical shock or injury to persons
when the appliance is used.
• The product has not been misused, abused, neglected, altered, modified or repaired by anyone.
• The product has been subjected to fair wear and tear.
• Theproducthasnotbeenusedfortrade,professionalorhirepurposes.
• Theproducthasnotsustaineddamagethroughforeignobjects,substancesoraccident.
Your warranty does not cover:
• Componentsthataresubjecttonaturalwearandtearcausedbynormaluseinaccordancewithoperating
instructions.
• Unauthorised/impropermaintenance/handlingoroverloadisexcludedfromthiswarranty.
• Forguaranteeclaimsyouwillneedtosubmitaproofofpurchaseintheformofavalidreceiptthatdisplays
date and place of purchase.
This warranty does not replace but is in addition to your statutory rights.
This warranty does not apply to accessories supplied with the product.
This warranty applies only to the original purchaser and may not be transferred.
Replacement products will be covered by the limited warranty for the balance of the warranty period from the date of
the original purchase.
Please note:
Only defective product or parts returned to place of purchase will be replaced under this warranty.
New Zealand Contact: Australia Contact
Brand Developers Limited Brand Developers Aust Pty Ltd
Level 1, 519-521 Lake Rd, Takapuna, 461 Plummer Street,
NorthShoreCity0622,Auckland,NewZealand PORTMELBOURNE,VIC3207
PrivateBag93204,Parnell,Auckland1151 FAX:+61396817825
FAX:+6493068203 AUSTCustomerCare:1800890840
NZCustomerCare0800002999
QB900NZ_30_120626_1.indd 13 12-06-26 12:58 PM
Brand
Developers
Limited
Brand
Developers
Limited
Brand
Developers
Aust
Pty Ltd
Brand
Developers
Aust
Pty Ltd
Printed in China
Illustrations may differ from actual product.
QB900NZ.E.120626.1
Z854
SAA110120EA
QB900NZ_30_120626_1.indd 14 12-06-26 12:58 PM
Loading...