Ninja 200, 78-012, 200H, 78-011 User Manual
A
D
B
C
FIG. 1: Front View
A
Recovery tank cover
B
Vacuum hose attachment
C
Recovery tank gravity drain and gate-type valve
D
Solution hose quick-connect
B
User Manual
Ninja Portable Extractors
200 and 200H Models (78-011, 78-012)
15180 Josh Wilson Road
Burlington, WA 98233
800-932-3030 www.LegendBrandsCleaning.com
Ninja Portable Extractors provide deep, rapid cleaning of carpets, upholstery and hard surfaces.
Heated models provide additional cleaning power. Lightweight, easy to use, and adjustable for a
wide range of carpet types and soiling conditions, the Ninja Extractors produce cleaner, drier
carpets and surfaces.
Patents: http://www.LBpatents.com
REA D A N D S A V E T H E S E I N S T R U C T I O N S
Intended Use
Ninja Portable Extractors are intended for
professional use only and are designed to clean
carpets and upholstery in an indoor environment.
They are not constructed for any other use. Use only
commercially available floor cleaning chemicals and
recommended accessories intended for your
specific model. Do not us this machine other than
described in this manual.
Shown with optional Wand and Vacuum Hose
Kit (48-103).
Notice: Risk of injury
Do not leave appliance when plugged in. Unplug
cord from outlet when not in use or servicing
machine.
Do not use outdoors. This machine is for indoor use
only.
Do not allow to be used as a toy. Close attention is
necessary when used near children.
Use only as described in this manual. Use only
manufacturer’s recommended accessory tools.
Operators shall be adequately instructed on the use
of this machine.
This machine is not intended for use by persons,
including children, with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge.
Do not use with damaged cord or plug. If appliance
is not working as it should, has been dropped,
damaged, left outdoors, or dropped in water, return
it to a service center for repair.
Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
07-02231A 200, 200H 1 Ninja
A
B
C
F
D
FIG. 2: Rear View
(Fig 2 detail)
A
A
Solution tank with clear hinged cover
E
Separate circuit indicator light (200H only)
B
Wand retention clip
F
Circuit breaker reset switches (200 has one switch)
C
Vacuum exhaust. Keep clear.
D
Product label and serial number
E
Do not pull cord to unplug. To unplug, grasp the
plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with
any opening blocked; keep free of dust, lint, hair and
anything that may reduce airflow.
Immediately unplug power cord from outlet if
machine leaks solution/foam or if machine tips over
while operating.
Release water pressure at accessory tool spray
nozzle before disconnecting solution hose.
Always stop machine on a level surface.
Do not use without ball float screen in place.
Turn off all controls before unplugging.
Do not use to pick up flammable or combustible
liquids, such as gasoline, or use in areas where they
may be present.
Do not pick up any type of hazardous dust or toxic
materials.
Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
Do not point spray at yourself or in the direction of
others.
Do not use this machine for dry vacuuming.
Do not operate machine in standing water.
Use extra care when cleaning on stairs. Do not
wheel machine up or down stairs.
Connect to a properly grounded outlet only.
Extension cord must be 12/3 gauge and no longer
than 40 feet. Replace cord if ground plug becomes
damaged.
Do not use additional extension cords with machine.
Do not use machine if not in proper operating
condition.
Do not modify machine from its original design.
Get assistance when lifting machine.
All repairs must be performed by a qualified service
person. Use only manufacturer-supplied or
equivalent replacement parts.
07-02231A 200, 200H 2 Ninja
A
D
B
G
C
F
FIG. 3: Control Panel
E
Blower ON/OFF
Solution pressure pump ON/OFF
Solution heater ON/OFF (200H only)
Cautions: Risk of property damage
to the original purchaser and proof of purchase is
required. Modifying this unit or not maintaining the
machine as outlined in this manual will void the warranty.
See the full Limited Warranty document for details.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should
malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with cords
having equipment-grounding conductors and grounding
plugs. The plugs must be inserted into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING! Improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualified electrician or service
person if you are in doubt as to whether the outlets
are properly grounded. Do not modify the plugs
provided with the appliance – if the plugs do not fit
the outlets, have proper outlets installed by a
qualified electrician.
This equipment is for use on a circuit or circuits having a
nominal rating no more than 120V and is factory-
equipped with a specific electric cord and plug to permit
connection to a proper electric circuit. Make sure that the
appliance is connected to outlets having the same
configuration as the plugs. No adaptor should be used
with this appliance. If the appliance must be reconnected
for use on a different type of electric circuit, the
reconnection should be made by qualified service
personnel.
CAUTION: Protect from freezing. Freezing may
damage internal components and will void warranty.
CAUTION: Do not use with water with over 3 grains
per gallon (51 miligrams per liter) of hardness. Use
with hard water could result in the formation of
mineral deposits inside pumps and fittings. Damage
caused by mineral deposits will void warranty.
CAUTION: Use only to extract moisture. Do not
immerse end of vacuum hose in liquid.
CAUTION: Do not use as a dry vacuum. Dust
particles will damage the vacuum motors. Damage
caused by dry vacuuming will void the warranty.
CAUTION: To prevent the growth of mold and
mildew inside the tanks, always drain waste tank
completely and empty solution tank after use.
WARRANTY
Visit www.LegendBrandsCleaning.com to register your
purchase. Registration allows us to better assist you with
using, maintaining or servicing your equipment, as well
as to contact you in case we have important safety
information concerning your product.
The warranty is valid from the date of purchase for one
year. This will cover parts and labor at an authorized
Sapphire Scientific distributor. The warranty is only valid
CONTROLS
ON THE CONTROL PANEL (Fig. 3)
Includes rocker-type switches control blower, solution
pump, and heat (on the 200H).
ON THE BACK PANEL (Fig. 2H)
Breaker reset switches. Press to reset as needed.
OPERATING INSTRUCTIONS
IMPORTANT: Make sure to control the amount of foam
in the recovery tank. Excessive foam can allow moisture,
carpet fiber and other debris to be drawn through the
vacuum cutoff valve and cause damage to the vacuum
motors. Damage caused by moisture or debris will void
the product warranty. To help reduce foaming, use a
low-foam detergent. Foaming may also occur because of
residues left from previous cleanings. If this happens,
use a defoamer additive. Follow defoamer manufacturer
instructions for proper application.
1. Pre-mix cleaning solution with hot water in a
separate container. Pour mixed solution into the
solution tank of the machine.
2. Connect vacuum and solution hoses to machine and
attach to extraction wand or hand tool.
07-02231A 200, 200H 3 Ninja
FIG. 4: Solution inlet filter cleaning
Remove
open top..
Unscrew
Rinse cap
FIG. 5: Vacuum cutoff valve cleaning
Slide filter off and lift out to remove.
Slide filter tube back into place. Rotate assembly to a
45° angle toward outside wall of tank. Reinstall.
nut with
9/16 in.
wrench
and lift
inline filter
cap assembly
and remove.
and filter
assembly
clean and
reinstall.
3. Plug power cord into a 3-pin grounded circuit. Keep
cords clear of your cleaning path. IMPORTANT:
Heated units have two cords and each cord should
be plugged into separate 3-pin grounded circuits.
The separate circuit indicator light will glow green
(Fig. 2F) when the cords are properly connected.
4. Switch on vacuum.
5. Switch on solution pump.
6. Switch on heat for heated solution (heated units
only).
7. Begin cleaning. Refer to industry-approved
procedures. NOTE: For heated units, it may require
several minutes for the solution to reach the
maximum temperature.
8. If equipped, solution pressure may be adjusted with
the pressure regulator knob (Fig. 2H). Monitor the
pressure gauge to ensure pressure is adequate.
9. Use gravity drain to drain waste tank when full.
Attach diverter to direct flow downward (Fig. 6).
CAUTION: When the recovery tank reaches capacity,
an automatic float valve blocks vacuum intake (Fig.
5) and the vacuum motors will make a high pitched
noise. When this occurs, switch the machine off
immediately to prevent damage to the vacuum
motors.
10. When cleaning is completed, rinse solution tank with
clear water to ensure no detergents or rinse agents
remain in the tank.
11. Empty and rinse the waste tank thoroughly. This will
help to prevent the formation of damaging deposits
and reduce the growth of odor-causing bacteria.
12. Turn on vacuum motor and allow it to run for 15
minutes to help remove any moisture from the
vacuum motors and help ensure long vacuum life.
MAINTENANCE
WARNING: Unplug machine before servicing.
Possibility of electrical shock.
WARNING: Interior components may be hot
after operation. Let unit cool completely
before servicing.
07-02231A 200, 200H 4 Ninja
ALL MODELS
Vacuum
motor
6.6 Ametek producing 659 peak air watts
Capacity
Solution tank 12 gal. | 37.9 l
Recovery tank: 10 gal. | 37.9 l
Construction
Rotomolded polyethylene housing and handle; 10 in. semipneumatic wheels.
Closed water
lift
137 in. | 348 cm
Power cord
One 25 ft. cord (non-heated units)
Two 1 ft. cords (heated units) and two 14/3 AWG 25 ft. ext.
cords
Drain valve
Gate type
Float shut-off
Ball type
Dimensions
(H × L × W)
41.5 × 30.25 × 19.75 in. | 105.4 × 76.8 × 50.2 cm
Model
Features
Dry weight
Amp draw
200
78-011
200 PSI
94 lbs.
42 kg
Circuit 1 13.5A
200H
78-012
200 PSI
1750W heater
102 lbs.
43 kg
Circuit 1 14.2A
Circuit 2 12.5A
FIG. 6: Gravity drain diverter
DAILY OR AFTER EACH USE
Clean the solution inlet filter (Fig. 4). Loosen tank
attachment screw (Fig. 1) and open unit. Remove filter
cover and strainer screen (Fig. 4). Rinse strainer screen
clean in warm water. Replace strainer and retighten filter
cover.
Clean vacuum ball float valve (Fig. 5). Empty recovery
tank, then open recovery tank lid. Grasp valve assembly
and pull gently toward the front of the unit, taking care
not to distort the strainer screen. Rinse assembly clean
and make sure float ball moves freely inside assembly.
Reinstall strainer and vacuum ball float valve assembly
securely.
AS NEEDED
Lubricate the solution line quick-connect coupling
(Fig. 1D) with a small amount of rust-inhibiting oil such
as LPS-3 or WD-40.
To maintain appearance, wipe interior and exterior
surfaces with a damp cloth. For deep cleaning and a
lasting, protective shine, use an automotive vinyl
cleaner/protectant product.
SPECIFICATIONS
OPTIONS (PURCHASED SEPARATELY)
Wand and Vacuum Hose Kit (48-103): Wand, 25 ft.
¼ in. solution hose and 25 ft. 1½ in. vacuum hose.
HOSS 700 Rotary Cleaning Tool (67-025). Use with
HOSS 700 Adaptor Kit (48-117).
Upholstery Pro (67-019-P)
07-02231A 200, 200H 5 Ninja
A
D
C
B
FIG. 1: Vista frontal
A
Tapa del tanque de recuperación
B
Conexión de la manguera de aspirado
C
Drenaje tanque recuperación y válvula compuerta
D
Conexión rápida de la manguera de solución
Manual de Uso
Ninja Extractores Portátiles
Modelos 200, 2200H (78-011, 78-012)
15180 Josh Wilson Road
Burlington, WA 98233
800-932-3030 www.LegendBrandsCleaning.com
Los Extractores Portátiles Ninja premiten una rápida y profunda limpieza de alfombras, tapicería
y superficies duras. Los modelos con calentador brindan un adicional poder de limpieza.
Ligeros, fáciles de usar, y ajustables para una amplia gama de tipos de alfombras y condiciones
suciedad, los Extractores Ninja dejan más limpias y secas las alfombras y las superficies secas.
Patentes: http://www.LBpatents.com
LEA Y C O N S E R V E E S T A S I N S T R U C C I O N E S
Uso previsto
Los Extractores Portátiles Ninja están diseñados para
uso profesional solamente y están diseñados para
limpiar alfombras y tapicerías en un ambiente interior.
No se construyen para ningún otro uso. Utilice sólo
productos químicos de limpieza para pisos disponibles
comercialmente y accesorios recomendados para su
modelo específico. No utilice esta máquina que no sea
la descrita en este manual.Aviso: Riesgo de
lesiones
No descuide la unidad cuando esté enchufada.
Desenchúfela cuando no esté en uso o cuando se la
esté reparando.
No usar en exteriores. La máquina está diseñada
sólo para uso interior.
No permita que se la utilice como juguete. Es
necesario prestar adecuada atención cuando se la
usa en cercanía de niños.
Usar sólo de la manera descrita en este manual.
Utilice sólo los accesorios recomendados por el
fabricante.
Quienes operen esta máquina deberán estar
adecuadamente instruidos en su uso.
Esta máquina no está pensada para que la utilicen
personas con capacidades físicas, sensoriales o
mentales limitadas, o con falta de experiencia o
conocimiento, incluyendo niños.
No utilizar en caso de que el enchufe o el cable se
encuentren dañados. Si la unidad no funciona como
debería, si se ha caído, dañado, si ha quedado en el
exterior o si le cayó agua encima, llévela a un centro
de servicio para su reparación.
No acarrearla tironeando de su cable, no use el
cable como manija, no cierre una puerta sobre el
07-02231A 200, 200H 6 Ninja
cable ni lo tironee sobre bordes o esquinas agudos.
No haga funcionar la máquina sobre el cable.
Mantenga el cable alejado de superficies calientes.
Loading...