NINGBO CSTAR IMP and EXP 0066 User Manual

55mm
70mm
TRUE WIRELESS EARBUDS
QUICK START GUIDE
FCC ID : 2ABHA0066
STEREO MODE
(DUAL EARBUD USE)
— Remove both earbuds from charging cradle and place them in your ears.
— Make sure Bluetooth Search Mode is turned off on your mobile device.
— Hold the right earbud button (7) for 3 seconds and then press left earbud button (5) for 3 seconds until they are powered on. (Earbud LEDs will ash Red and Blue to indicate that they are in Link mode.)
— Earbuds will automatically link together after
a few seconds,and earbuds will have a tone,
One earbud will flash red and blue,and the other earbud will flash blue only.
— Once Earbuds are linked together you may
proceed to pairing with your mobile device.
1 Micro USB charging port 2 Charging Case LED indicators 3 Charging Case Power Button
L
Left Earbud
Pause/Play/Answer Call/End Call, Next Track
1
2
4 Left earbud LED indicator 5 Left control button 6 Right earbud LED indicator
7 Right control button
R
/
Right Earbud
R
7
6
L
PAIRING
— Enable Bluetooth search mode on your mobile device and search for
GETTING STARTED
pairing name “ it on your mobile phone. Once the
TWS-i7
*Note: Once earbuds have been initially paired successfully with your mobile device they will automatically pair the next time
they are powered on.
Model: CT04001 Item No.: CPP-4635 Capacity(Cradle): 350mAh / 3.7V (1.295Wh) Capacity(Earbuds): 50mAh /3.7V (0.185Wh) Input of earbuds: 5V / 60mA Input of Cradle: 5V / 300mA
earbuds are successfully paired a notification will sound .
— Now you can enjoy your true wireless Bluetooth Earbuds.
CPP-4635 ” and select
CHARGING YOUR CASE
— Charge on the go charging case, with the included micro USB cable for 2-3 hours.
Do not charge longer than suggested time. Do not charge overnight.
— When LED is illuminated solid red battery case is fully charged.
5 4
Flashing RED- Battery Case is charging Solid RED- Battery Case is fully charged
Charging LED Indicators
Solid BLUE- Battery Case is charging earbuds OFF- Battery Case is o
Front
OPERATING BLUETOOTH EARBUDS
Function Operation Power On Press (5) or (7) for 3 seconds
Power Off Press (5) or (7) for 5 seconds Play/Pause Single press (5) or (7) Answer Reject
Earbuds LED indications (4) & (6)
Power On
Two earbuds paired each other successfully
Paired Successfully Flashing Blue
Power O
Earbuds in Cradle
Fully Charged
Charging Case
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
Charging
Single press (5) or (7) Press (5) or (7) for 2 seconds
Red and Blue LED will ash altemately
One earbud will flash red and blue, and the other earbud will flash blue only.
LED O
Solid Red Solid Blue
See CHARGING YOUR CASE
CHARGING YOUR EARBUDS
— Place Right and Left Earbuds in battery case charging cradle and press the power button on the battery case (3)
— Charging case LED indicator will illuminate Blue and the earbud LED indicators (4, 6) will illuminate Red, indicating that the earbuds are charging properly. When Earbuds LEDs (4, 6) turn solid blue, earbud batteries are fully charged.
— After earbuds are fully charged, press the charging case power button (3) to turn the charging case OFF.
Note:This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequence energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not accor in a particular installation.if this equipmemt does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from
that to which the receiver is connectec.
• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The devicecan be used in portable exposure condition without restriction.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by (ShenZhen C-Star Electronic Tech. Co., Ltd.) is under license. Other trademarks and trade names are those of their respective owners.
MONO MODE
(SINGLE EARBUD USE)
— Remove earbud from charging cradle power on by pressing the control button or (5) for 3 seconds depending on whic earbud your using.
— Once earbud is powered on, proceed
Back
Loading...