NINGBO CSTAR IMP and EXP 0044 User Manual

Metal Bluetooth Speaker

and Wireless Charging Pad

Instruction Manual

SL240

Functions:

1.

Play/Pause/ON/OFF

2.

Bluetooth LED Indicator

3.

Vol +/Next Track

4.

Wireless Charging LED Indicator

5.

Vol-/Previous Track

6.

Micro-USB charging port

7.

Charging LED Indicator

8.

Wireless Charging Pad

What’s included:

1 x Metal Speaker
1 x USB to Micro-USB Charging Cable
1 x Instruction Manual

Playing time: up to 2hrs at max volume

•

Charging time: up to 1.5hrs

•

Pairing Name: “Metal Wireless”

•

Instructions:

(Be sure to fully charge the speaker before

Charging the Speaker

1.
Connect the provided charging cable to a

•

power source and to the micro USB port on
the speaker (6).

The LED indicator light will glow red when
charging and turn off when fully charged.

Wireless Charging:

2.
Connect speaker to a 2A output with the

•

provided cable, Wireless Charging LED(4)
will glow red once connected.
Place wireless charging supported mobile

•

device on top charging pad, LED will glow

green when device is charging.

Phone will begin to charge automatically.

•

Bluetooth® Setup:

3.
Press and hold Power Button(1) to turn ON

•

the speaker, Bluetooth LED Indicator(2) will

Turn on the Bluetooth function on

•

mobile device, Select “Metal Wireless”
pairing name. LED will turn solid BLUE if
successfully paired.

Speaker will automatically pair if the mobile

•

device has been paired before.

Press and hold Power Button(1) to turn off

•

the device.

Playing Music:

4.
Short press “Play/Pause” key to pause

•

music. A second short press will resume
playing music again.
“Vol+/Next track”:

•

Short press - next track.
Long press - increase volume.
“Vol-/Previous track”:

•

Short press - previous track
Long press - reduce volume

SAFETY PRECAUTIONS:

•

WARNING-When using this product, basic
precautions should always be followed:

1.

Read all the instructions before use.

2.

Never store or use this product in
temperatures below 32°F(0°C) or above
115°F(45°C).

3.

Do not overcharge Phone. Unit may get
hot with excessive use. Remove Phone
when it is fully charged. Never charge for
more than 7 hours at a time.

4.

The unit’s full performance is achieved
only after 2 or 3 completed charge and
discharge cycles.

5.

To reduce the risk of injury, close
supervision is necessary when the product
is used near children.

6.

Do not expose the device to moisture.

7.

Do not use the device in excess of its
output rating. Overload outputs above

8.

Do not use the device if damaged or

9.

explosion or risk of injury.

10.

Do not disassemble the device. For

professional. Incorrect reassembly may

11.

or temperatures above 104°F may cause
explosion.

12.
use only identical replacement parts to
ensure product safety

MADE IN CHINA

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may
cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a class B
digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequence energy and,if not
installed and used in accordance with the instructions,may cause harmful interference to
radio communications.However,there is no guarantee that interference will not accor in a
particular installation.if this equipmemt does cause harmful interference to radio or
television reception,which can be determined by turning the equipment off and on,the user
is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an autlet on a circuit different from that to which the

receiver is connectec.

• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The devicecan
be used in portable exposure condition without restriction.