Quick Guide
For Android Tablet
Ninebot VA50EC
1
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Caution:
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation
2
RF exposure warning :
This equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.
Information for the OEMs and Integrators :
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other
restrictions.
End Product Labeling :
This transmitter module is authorized only for use in device
where the antenna may be installed such that 20cm may be
maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
"Contains FCC ID: 2ALS8VA50EC ” and "Contains IC:
22636-VA50EC “.
3
Devices shall bear the following statement in a
conspicuous location on the Host :
"This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation. "
Note: If the host is so small or for such use that it is not
practicable to place the statement, the text associated with the
logo may be placed in a prominent location in the instruction
manual or pamphlet supplied to the user. However, the unique
identification (trade name and model number) and the logo must
be displayed on the host.
Canada, Industry Canada (IC) Notices
This device complies with Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
4
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de
licence RSS standard(s).
Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas causer d'interférence et (2) cet
appareil doit accepter toute interférence, notamment les
interférences qui peuvent affecter son fonctionnement.
En vertu de la réglementation de l'industrie du Canada, cet
émetteur de radio ne peuvent fonctionner en utilisant une
antenne d'un type et maximum (ou moins) Gain approuvé pour
l'émetteur par Industrie Canada. pour réduire risque
d'interférence aux autres utilisateurs, le type d'antenne et son
gain doivent être choisis de sorte que la puissance isotrope
rayonnée équivalente (PIRE) ne dépasse pas ce qui est
nécessaire pour la réussite de communication.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the
Industry Canada (IC) radio frequency exposure limits. The
Wireless Device should be used in such a manner such that the
potential for human contact during normal operation is
minimized.
This device has also been evaluated and shown compliant with
the IC RF Exposure limits under mobile exposure conditions.
(antennas are greater than 20cm from a person's body).
5
Informations concernant l'exposition aux fréquences
radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à
la limite d'exposition aux fréquences radio d'Industry Canada (IC).
Utilisez l’appareil de sans fil de façon à minimiser les contacts
humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux
limites d'exposition aux RF d'IC dans des conditions d'exposition à
des appareils mobiles (antennes sont supérieures à 20 cm à partir
du corps d'une personne).
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
ATTENTION
RISQUE D'EXPLOSION SI LA BATTERIE EST REMPLACÉE
PAR UN TYPE INCORRECT. RECYCLEZ LES BATTERIES
USAGÉES SELON LES INSTRUCTIONS.
6
Layout
No.
Name
No.
Name
1
Right Infrared Camera
4
Left Infrared Camera
2
SoC Color Camera
5
Motion Camera
3
LED Flash Light
Base Head unit
Front
7
Top
No.
Name
No.
Name
1
LCD Tape Cable
4
SPI Header
2
Camera Tape cable
5
6-pin Battery Connector
3
Power Jack
8
Back
No.
Name
1
Micro USB Type C / OTG Port
9
LCD Unit
No.
Name
No.
Name
1
LCD Touch Panel
2
8M-pixel Camera
Front
10
Back
No.
Name
No.
Name
1
UART Header
3
Camera Tape Cable
2
Mic Array Header
4
LCD Tape Cable
11
Battery Unit
No.
Name
No.
Name
1
Battery Chamber
2
6-pin Battery Connector
12
Specifications
Processor
Intel Cherry Trail Type4 Z8550 /
Z8750
2.4GHz,64bit
Memory
LPDDR3 1600
4GB
Storage
eMMC MLC 5.0
64 GB
Wireless
Wi-Fi 802.11 ac, Bluetooth 4.0
dual band
Touchscreen
4.3” IPS
Resolution: 480x800 pixels
5 Point Multi Touch
Capacitive support
Cameras
DS4T Module (2 MP camera )
Right infrared camera
SoC color camera
Left infrared camera
Motion camera
8M pixel front camera
Battery
Li-polymer
18650 2600mAh
13
Input/Output
Power connector: 12V/3A
1 x USB Type C / OTG
1 x LD0 Power
1 x SPI
Mic Array ; Audio Code :ALC5672
OS
Google Android 5.1 Lollipop
CTS
Dimension
(mm)
LCD: 133 x 76 x 14~24.5 mm
Base: 129 x 88 x 20~25 mm
Weight
350g
Loading...