Page 1
Thank you for purchasing D_Core.
This product has a variety of massage
functions, which can be used to relieve
fatigue and improve body function.
We hope to always be a good partner in
your daily health management.
DC-1000A
User’s Manual
Table of Contents
Safety Precautions.............1
Part Names and Functions.. 8
Before Use..........................10
Adjustment of the Massage Chair
Method of Operation........ 17
Auto Programs................... 18
Manual Programs............... 20
Troubleshooting ................ 22
Safety Check .....................23
FAQ...................................... 24
DC-100A
DC-001A
.15
Care and Storage
After Sales Service ...........26
Specification ......................27
Dealer...................Back cover
Please read this manual before using this machine in order to use it correctly.
◎
Please store this manual in a convenient place for users to find, in case of need.
◎
This machine is only for domestic use. If it is used for non-domestic purposes
◎
(such as commercial use), please consult the store or dealer where you purchased it.
..............25
Page 2
Safety Precautions
Please read the safety precautions carefully before using this machine in order
to use it correctly. To ensure that you use the machine correctly and safely, so
as to avoid causing personal injury or property damage to you and others,
please read this article after fully understanding the following contents
(illustrations, marks) and make sure that you strictly abide by them. In addition, please refer to pages 8-9 for the names of each part.
Types of illustrations
Warning
【Safety Precautions】
Caution
The risk of death or serious injury may arise from wrong
operation.
Mis operation may cause injury or property loss.
Types and Contents of Marks
Indicates prohibited behavior.
(The left icon indicates no disassembly)
Indicates the directive of the mandatory behavior.
(The left icon shows pulling the power plug out of the socket)
After reading, please store this manual in a convenient place for users to find, in case of need.
Cautions in Places of Use
Caution
● Do not use in places with heavy moisture such as bathrooms or saunas.
Caution
Enforcement
Circuit
grounding
1
→ Otherwise, it may lead to electric shock or malfunction.
● Place this machine on flat ground for use.
→ Otherwise, it may cause the massage chair to topple and cause an accident.
This machine must be grounded. If it breaks
●
down or is damaged, the risk of electric shock
can be reduced. This machine is provided with
a grounding wire within the power cord, which
can be grounded by plugging in the power plug.
The power plug must be inserted into a socket
●
that is properly installed and grounded in
accordance with local laws and regulations. If
you have any questions about whether the
machine is grounded correctly, you can ask a
professional to check.
The grounding plug of this product is shown in
●
the right figure. If it doesn't match the socket
in your home, you need to connect an adapter
sold on the market.
Grounded socket Grounded socket
Ground pin Ground pin
Ground pin Ground pin
Grounded socket Grounded socket
Page 3
Cautions Before Use
Warning
● The following persons must not use this machine.
Persons forbidden to receive a massage by doctors, such as those suffering from
◎
thrombosis (embolism), severe aneurysm, acute venous aneurysm, various skin
inflammations and skin infections (including inflammation of subcutaneous
tissue).
● Do not use a power supply other than AC 120V.
Caution
Enforcement
→ Otherwise, it may lead to fire or electric shock.
● Do not use transformers.
→ Otherwise, it may lead to malfunction or electric shock.
Do not use this machine when the power cord or plug is damaged or the
●
socket is loose.
→ Otherwise, it may lead to electric shock, short circuit and fire.
● The following persons should consult a doctor before using.
◎Cardiac patients
◎Persons with perceptual impairment caused by severe peripheral vessels circulation disorders such as diabetes
◎Persons suffering from osteoporosis, cervical fracture, acute pain
◎Persons with trauma in a treatment area
◎Persons with a body temperature above 38℃ (high fever period) for example:
severe period of acute inflammatory symptoms (tiredness, chills, unstable blood
pressure, etc.). When the body is weak.
◎Persons in the beginning of early pregnancy or shortly after delivery
◎Persons who are using implantable medical devices susceptible to electromagnetic interference such as cardiac pacemakers
◎Persons with an abnormal spine or curved spine
◎Persons who want to use it on areas that have been treated by a doctor or where
the ailment is now being treated
◎Malignant Tumor Patients◎Persons requiring quiet recuperation
◎ Patients with acute diseases including visceral diseases (gastritis, enteritis and
hepatitis)
◎Persons undergoing medical treatment, especially those who feel abnormal
◎Persons with joint deformations caused by rheumatism, gout, etc.
◎Persons with symptoms of dizziness, unstable standing, tinnitus
◎Persons with inflammatory reaction due to contusion, muscle strain, etc.
◎Persons with tenosynovitis or may have tenosynovitis
◎Persons considered to have temperature loss disease
Before massage, it is necessary to confirm whether there is cracking or
●
damage in the fabric at the massage site. Please check other parts to
make sure the fabric is not damaged. If any damage is found on the
fabrics, regardless of the size of the damaged area, please unplug the
power and contact the dealer whom you purchased it from. Please do not
remove the fabric from the massage area or use it when the fabric is
damaged, otherwise there will be serious safety hazards.
If the machine is used when the fabric is damaged, it may cause injury or electric
→
shock.
Elderly or fragile people should consult a doctor before using it, even if
●
there is no specific disease.
● Consult a doctor or specialist if it is ineffective after use.
● Do not let children and pets use or play with this machine.
【Safety Precautions】
2
Page 4
Cautions Before Use
Cautions Before Use
Caution
●
Do not use this machine in a way not described in this manual. In addition,
do not use this machine with other equipment or cover with an electric
blanket.
→Otherwise, it may have a bad influence on the body or cause injury.
●Do not move the massage chair in a manned state.
→Otherwise, the massage chair toppling may result in an accident or injury.
【Safety Precautions】
Prohibited
Enforcement
●Do not sit on the chair’s when it is reclined.
Otherwise, it may cause excessive pressure on the leg components, causing
→
malfunction.In addition, the massage chair toppling may result in an accident or
injury.
Do not use other items or accessories other than those that were
●
included with the machine.
Before plugging the power plug into the socket, make sure that the main
●
power switch is in the "OFF" state.
→Otherwise, it may lead to malfunction or electric shock.
●Please fully insert the power plug and connector.
Otherwise, it may lead to electric shock, short circuit and fire.
→
Before use, please follow this manual, turn on all switches in turn, and
●
verify the normal operation of the machine.
●At the beginning, please start with a mild massage program.
Excessive massage stimulation at the beginning may cause injury. Especially for
→
people who are old or fragile, please pay attention when you massage.
For the sake of safety, please confirm the position of the massage mecha-
●
nisim. If the device is not in the storage position, please switch on the
main power switch and sit down slowly after confirming that it has been
stored. Please refer to page 7 for the storage position.
●
Do not squat, stand or sit on legrest.
→The massage chair toppling may result in an accident, injury or malfunction.
If the machine has not been used for a long time, please re-read this
●
manual to confirm that the machine can be operated normally before use.
3
Page 5
Cautions Before Use
Warning
Do not wrap the power cord around the massage chair or step on the body
●
and leg components. In addition, do not damage, process, over-bend,
stretch or twist the power cord.
→
Otherwise, it may lead to wire damage, fire or electric shock.
● Do not sprinkle water or other liquids on the massage chair.
→ Otherwise, it may lead to electric shock, short circuit and fire.
Do not sit in the massage chair with water on your body, or operate with
●
wet hands.
→ Otherwise, it may lead to electric shock or malfunction.
Do not allow the massage chair to be used by children, people who are
●
unable to express their will or the disabled. In addition, do not allow
children or pets to play on or around the massage chair (behind the back of
Prohibited
the chair, below the leg components, etc.), or squat and sit on the massage
chair.
→
Otherwise, it may lead to an accident or injury.
Do not use the massage chair with more than 1 person in it, including when
●
holding a child (baby, etc.).
→ Otherwise, it may lead to an accident or injury.
When the fabric is damaged, please stop using it and remove the power
●
plug from the socket.
Otherwise, it may lead to an accident, injury, or electric shock. For repairs,
→
please contact the dealer.
Do not touch the LED part directly when the light is on or just after it is
●
off.
→ Otherwise, it may lead to electric shock or malfunction.
【Safety Precautions】
Enforcement
●
Make sure no one (especially children) or pets are around before starting
massage, when standing up, or when lowering the back of the chair. In
addition, please be careful not to let the body or items clamp behind the
back of the chair or under the legrest.
→ Otherwise, it may lead to an accident or injury.
If your body or items are clamped, please press the back adjustment
●
button to return the back of the chair to a safe position.
Do not cover or touch the LED part with flammable articles such as cloth,
●
paper, plastic, etc.
Do not insert metal items (ex. hairpin, pin) into the gaps of the machine
●
(especially the LED part and the power cord).
→ Otherwise, it may lead to electric shock, short circuit or fire.
4
Page 6
【Safety Precautions】
5
Safety Precautions
Cautions When Using
Caution
●Do not use the massage chair directly with bare skin.
Do not use the massage chair for purposes other than massage and for
●
sitting.
→ Otherwise, it may lead to an accident or injury.
Do not put your hands in the movable parts such as the upper and lower
●
parts of the massage wheel in the back of the chair. In addition, do not
wear hard objects such as belts when using.
→ Otherwise, it may lead to injury or malfunction.
●
Do not use on head, chest, abdomen, joints (elbows, knees, etc.).
→ Otherwise, it may cause physical discomfort or injury.
●Do not run the massage chair unattended.
Prohibited
Enforcement
→ Otherwise, it may lead to an accident or injury.
●The legrest can only be used on the legs.
→ Otherwise, it may lead to injury.
When massaging the legs, if legs are removed, do not force the legs back
●
into the legrest when a massage is in progress.
→ If forced into, it may lead to malfunction.
●The armrests can only be used on the forearms and wrists.
→ Otherwise, it may lead to injury.
When massaging the forearms, if arms are removed, do not force the arm
●
back into the armrests when a massage is in progress.
→ If forced into, it may lead to malfunction.
●Do not look directly into the LED component.
→ Otherwise, it may lead to injury.
In case of an emergency or abnormal operation of the massage chair,
●
please press the [EMERGENCY STOP] button of the remote control to
stop the massage.
If you feel severe pain or physical abnormality during use, please stop
●
using immediately and consult your doctor.
If you feel that massage is too strong, please reduce the stimulation
●
according to this manual. If the stimulation is too strong after adjustment,
please stop using it and contact the dealer (recorded at the bottom of
the cover).
→ If you feel that the massage is too strong but continue to use, it may lead to injury.
Avoid falling asleep during massage.
●
→ Otherwise, it may lead to injury.
Total massage time should not exceed 60 minutes per day. Massages
●
should be taken in intervals of 90 minutes or less, with significant breaks
between sessions. Do not massage any one area continuously for more
than 5 minutes at a time.
Prolonged and continuous use may cause excessive stimulation, resulting in
→
adverse effects or injury.
Make sure there are no people (especially children) and pets around
●
before use.
→ Otherwise, it may lead to an accident or injury.
●Do not remove the back cushion during massage.
Page 7
Cautions When Using
Caution
When power failure or possible power failure occurs, please stop using it
●
immediately, turn off the power switch and unplug the power plug from
the socket.
→Otherwise, the restoration of the power supply may lead to an accident or injury.
During thunderstorms, please stop using it immediately, turn off the
●
Unplug the
power plug
power switch, and unplug the power plug from the socket.
When the massage chair does not work or is acting abnormally, in order to
●
prevent accidents, please stop using immediately, turn off the power
switch, unplug the power plug from the socket, and contact the dealer for
repair.
Otherwise, it may lead to electric shock, leakage or short circuit, thus causing
→
fire.
Cautions After Use and When Not in Use
Caution
●Do not use the power cord on equipment other than this machine.
After using this machine, the back of the chair must be completely
●
Prohibited
Enforcement
Unplug the
power plug
upright.
●Do not place items on the massage chair.
●Do not replace the LED.
After use, please turn off the power switch and pull the plug out of the
●
socket.
Otherwise, it may lead to an accident or injury caused by children or pets playing
→
with it.
● After use, please clean and place it in a dry place.
When unplugging the power plug from the socket, do not pull the power
●
cord directly. Instead, hold the power plug and pull it out.
→Otherwise, it may lead to electric shock or short circuit, thus causing fire.
Always unplug the power plug from the socket before cleaning and
●
maintenance, and do not unplug the power plug with wet hands.
●Always unplug the power plug from the socket when not in use.
Dust or moisture may lead to aging of wire insulation, resulting in electric shock,
→
leakage or fire.
【Safety Precautions】
6
Page 8
【Safety Precautions】
Enforcement
Safety Precautions
Other Cautions
Warning
Do not stand on the massage chair. Do not put excess pressure on the
●
massage chair, such as sitting anywhere other than the seat.
Prohibited
No
dismantling
Caution
→ The massage chair toppling may result in an accident, injury or malfunction.
If the massage chair breaks down, please contact the store or dealer
●
(recorded at the bottom of the cover). Do not repair it by yourself.
When the power cord is damaged, please entrust the dealer (recorded at
●
the bottom of the cover) to replace it, so as to avoid the occurrence of
danger.
●
Do not modify the massage chair.
→ Otherwise, it may cause fire, electric shock or injury.
If the massage chair is transferred or lent to others, please be sure to
●
give this manual together with the massage chair to the other party.
Caution
When discarding this product and accessories, please consult the nearest municipal
●
office for the correct the method to dispose of it.
7
Page 9
Part Names and Functions
※The illustration is a schematic. Different models will have different shapes.
Armrest (Right)
Remote
control
Remote
control
bracket
Arm pad
Chair
seat
Legrest
Back cover
(upper)
Back cushion
Chair back
Shoulder
components
Armrest (Left)
Back base
【Part Names and Functions
】
Main power
switch
Access port
Power plug
Power socket
Power cord
Castors
Leather
cover
Back cover
(lower)
8
Page 10
Part Names and Functions
POWER
Shiatsu
Knead
Shiatsu
3D
Intensity
Roller
Heat
Leg & Foot
Arm
Massage
Massage
Shiatsu
Quick
Recovery
Morning
Night
Air Focus
Roller
Auto/Manual
Width
EMERGENCY
STOP
Circulation
Neck &
Shoulders
Air
Intensity
Back
Speed
Speed
Auto Programs
Manual Programs
Left
Center
Right
Down
Up
Full
Upper
Lower
Wide
Mid
Narrow
Back
Leg
①
【Part Names and Functions】
⑤
⑦
Range
② ③
Master
Lower
Knead
Tap
Balance
④
⑥
⑧
⑨
Power button
①
Auto/Manual Mode
②
selection button
EMERGENCY STOP
③
button
Auto program
④
buttons
Back/Leg Recline
⑤
buttons
Roller position
⑥
adjustment button
Massage Intensity
⑦
adjustment buttons
Heat
⑧
(not on all models)
Manual program
⑨
buttons
Turns on or off the power
supply of the remote control.
The blue light is always on
when the remote control is
powered on. If this button is
pressed during the operation
of the massage chair, the
massage will stop after the
massage wheel returns to the
storage position.
Automatic programs and
Manual programs can be
changed. Auto programs can be
selected when the remote
control is powered on, and the
indicator light is off. Manual
programs can be selected with
the indicator light is on.
Press this button in case of an
emergency or if there is a
malfunction with the massage
chair. The massage chair will
stop immediately.
Press each button to
select/start the program.
Used to adjust the tilt angle of
the back and/or legs.
Used to adjust the shoulder
position when detecting
acupressure points, as well as
to adjust the position of the
massage wheel when using a
Manual program.
3D adjusts the strength of the
back massage device. Air
adjusts the strength of the
armrest and legrest.
Press to turn the heat on/off
and to adjust the temperature.
Basic operations and special
operations can be selected.
※The remote control is different depending on the model.
The illustration is of DC-100A. Other models may have fewer features.
9
Warning
Caution
●Do not spill water on the remote control.
●Do not operate with wet hands.
●Do not sit on, throw, or step on the remote control, and do not forcibly pull the remote
control cable.
●Do not press the button with sharp or hard objects.
→Otherwise, it may lead to damage.
Page 11
Before Use
This product is packaged in the condition so that the back of chair is completely flat.
●
Before use, be sure to fix the chair back along with the armrest.
When the room temperature is low, if you want to increase the indoor temperature
●
and use the massage chair, please gradually increase the temperature, and do not
heat up too quickly. Please wait for 1 hour before starting to use this machine when
moving from cold storage to a warm room.
→
Otherwise, condensation may occur at the operating position and the performance cannot be
fully realized.
About the placement of the chair
Please ensure that there is more than 20 cm(7.87 inch) of space left behind the massage
chair and more than 70 cm(27.55 inch) of space left in front of the massage chair, so as
to avoid touching the wall or other items when the back of the chair is tilted.
● Do not use in places with heavy moisture such as bathrooms or saunas.
Do not place the massage chair base against the power cord.
●
Do not place the machine in direct sunlight or near the places of high
Caution
To prevent damage to the floor and to reduce running noise, please lay carpets under the massage
●
chair. (Do not lay on electric blankets.)
Because the massage chair is heavy, please pay attention not to damage the floor when it is put on
●
the ground.
●
Please place the massage chair 1 m away from any audio-visual electronic equipment such as TV’s or
radios. Otherwise, noise may be produced.
●
If a person weighing 100 kg(220 lbs) is sitting in the massage chair, the weight is about 3.9 kg per
cm²(55.5 lbs per in²).
●
temperature such as heating appliances.
● Do not let open fires such as cigarettes or ashtrays near the massage chair.
● Do not use in places directly facing air conditioning.
20cm(7.87 inch)
70cm(27.55 inch)
【Before Use】
Confirm the items in the packing box
Please make sure that the body, legrest, aremrest (left/right) and accessories are
contained in the packing box.
Body
Armrestslegrest
User’s manual
Remote control
bracket
Accessories
Power cord
Back cover
(upper)
Assembly screws, Tool
(6 screws, 2 blots, 2 washers,
1 L-shaped wrench)
Cushion
Back cover
(lower)
10
Page 12
Before Use
Placement method and assembly method
The legrest and armrest (left/right) are respectively packaged in the packing box. Please
assemble them before use when they are placed for the first time. In addition, please follow
the opposite steps to disassemble and reposition the machine and then reassemble it for use.
Caution
●When placing and assembling, please take full care to avoid pinching hands or articles.
●Do not place the massage chair base on top of the power cord.
Lift the legrest, and insert
①
the shaft of the unilateral
legrest into the hole in front
of the massage chair and
press in.
Slide the legrest to the
②
opposite side, insert the
shaft of the other side into
the hole in front of the
massage chair, and insert the
resin washer and bolt.
③
Connect the airlines (same
colors together) and electric
cables from legrest to base of
the chair.
【Before Use】
④
Pull the back of the armrest
(part □ in the picture) to the
bolt on the back of the
massage chair, and place the
center of the armrest (part 〇
in the picture) on the frame
of the massage chair seat.
※
Be careful not to pinch the
airlines or electrical cables.
⑤
Use screws to fix the armrest
and the massage chair in the
order of A-C.
The armrests fixture is in the
※
storage state. Please pull it
apart.
A
⑥
Connect the airlines and the
electric cable (connect the
same colors together).
※
The number of hoses and cables
varies with the model of chair.
11
C
B
Page 13
Fasten the zippers of the arm
⑦
pad and the chair seat.
※
Put the air hose and cable
connected in step⑥ inside the
arm pad.
Follow steps ④~⑦ to connect
⑧
the arm on the opposite side.
Hang the back cover (upper)
⑨
fixing belt onto the hook on
the back of the left and right
armrest and press it inward.
【Before Use
Hang the back cover onto the
⑩
hook of the armrests and lock
it with the fastener.
※
Be careful not to pinch the
leather cover, and make sure
that the leather cover on the
side of fixed belt on the back
cover (lower) is inside the
armrests.
Fastener
(left and
right)
Hook
⑪
Unscrew the screw on top of
the armrest (right), put the
remote control bracket on and
then resecure the screw.
Adjust the remote control
bracket to your preferred
angle before installation.
※
Be careful not to pinch the cable
of the remote control.
※
To adjust the angle again, be
sure to loosen the screw before
adjustment.
⑫
Push the cable of the remote
control through the round
hole on the front side of the
arm component (right) and
press the snap button firmly.
】
12
Page 14
Before Use
How to Move Your Chair
Before moving your chair, always turn off the main power switch and remove the power
plug from the electrical socket.
The massage chair has rolling casters on the rear side of the base. These allow for one
person to move the massage chair for a short distance on their own. To move the chair
using this method, carefully full reclining the chair back and legrest onto its rolling
casters by lifting the armrest, then roll the chair to the desired position. Never lift the
chair by the legrest or by holding on to the wooden parts.
View at
※
Opposite
side
【Before Use】
NO
13
YES
If it is impossible to move by using the method shown above, please follow the assembly
instructions as shown on page 11 and 12, to remove the armrest and legrest, and then
move; if it still cannot be moved, please contact the dealer recorded at the back cover.
■
Because the massage chair is heavy, please wear special gloves when moving it to avoid dropping or
causing injury.
■ Because the massage chair is heavy, please pay attention not to hurt one’s back when moving.
■ The remote control is connected to the massage chair, so please be careful not to drop it when moving.
●Please pay attention to avoid applying strong force to wooden parts.
Caution
●Do not move the massage chair with a person in it.
●
Please pay sufficient attention to avoid clamping the foot and power cord
when moving.
●Please take care to avoid damage to the floor by castors.
Page 15
Confirmation of fabrics
Open the zipper on the top of the cushion and lower the
back cushion forward, and confirm whether the cloth of
the massage chair is damaged or not. In addition, please
check other parts to make sure the fabric is not damaged.
●
Before massage, it is necessary to confirm whether there is cracking or damage
in the fabric at the massage site. Please check other parts to make sure the
fabric is not damaged. If you find any damage on the fabric, please unplug the
Warning
power plug regardless of the size of the damaged part, and contact the dealer
(recorded at the bottom of the cover). Never remove the fabric from the
massage part or use it when the fabric is damaged, otherwise there will be
serious safety hazards.
Method of powering on
Insert the connection port of the power cord into
①
the access port.
Insert the power plug into the socket.
②
Zipper
【Before Use】
Turn on the main power switch behind the massage
③
chair.
● Do not use transformers.
Warning
Caution
→Otherwise, it may lead to malfunction or electric shock.
● Do not use outside the country where you purchased it.
→Otherwise, it may lead to malfunction or electric shock.
Before plugging the power plug into the socket, make sure that the
●
main power switch is in the "OFF" state.
●Please fully insert the power plug.
Before use, please follow this manual, turn on all switches in turn,
●
and verify the normal operation of the machine.
14
Page 16
Adjustment of the Massage Chair
Sitting method of the massage chair
In general, the massage mechanisim is retracted in the storage position. For safety,
please check the position of the massage device. If the massage device is located outside
the above position, do not sit down immediately, but turn on the main power switch. After
the massage device returns to the storage state, slowly sit in the center of the massage
chair. (storage position is state of the chair back most rised and legrest most low.)
Do not sit on a chair with its back reclined.
●
→
Otherwise, it may cause excessive pressure on the back and arm components of the
Caution
When sitting down or exiting the chair, do not use the wooden railings of the arm for
support. This, it may cause malfunction. Please support yourself with the upholstered arm
component when sitting down or exiting the chair.
【Adjustment Of the Massage Chair】
NO YES
chair, causing malfunction. In addition, the massage chair toppling may result in an
accident or injury.
● At the beginning, please start with a mild massage program.
15
Application method of the cushion
If the stimulation of the massage is too strong, please place the accessory cushion on the
back cushion or the seat during the massage
Cushion
Caution
● Please make sure that the cushion is not curled or misaligned.
→Otherwise, it may lead to malfunction or injury.
Page 17
Application method of armrest
As shown in the figure below, the elbow is between the armrest and the back of the chair
when placing the arm. In addition, please adjust the shoulder position to your preferred angle.
Please put your elbow between
the armrest and the back.
Keep palms facedown.
●Can only be used for the arm.
→Otherwise, it may lead to injury.
When massaging the arm, do not force the arm into it after it has been pulled
●
Caution
out of the armrest.
→
If forced into, it may lead to malfunction.
Do not massage your elbows. Keep your palms down while you are receiving a
●
massage. Do not put your arm in any other direction.
→Otherwise, it may lead to injury.
Please adjust the
shoulder position
to your preferred
angle.
Adjusting Chair Tilt Angle
Press the back adjustment buttons to adjust the tilt angle of the chair’s back. Press
the leg adjustment buttons to adjust the tilt angle of the legrest.
■Inclining the back of the chair
Incline the back of the chair by the pressing the Back Up button. At the same time
the legrest will lower.
■Raising the legrest
Raise the legrest by pressing the Leg Up button.
【Adjustment Of the Massage Chair】
Back Leg
■Reclining the back of the chair
Lower the back of the chair by pressing the Back Down button. At the same time,
the legrest will raise.
■Lowering the legrest
Lower the legrest by pressing the button on the lower side of the foot.
Before starting the massage and when reclining the back of the chair, make
●
Warning
sure there are no people (especially children) and pets around. In addition,
please be careful not to get your body or items clamped behind the back of the
chair or under the legrest
16
Page 18
【Method of Operation】
Method of Operation
Types and characteristics of programs
【Auto programs】
By setting the menu in advance, you can easily select the program that suits your purpose
and use with one click.
It is highly recommended for people with a limited
massage time.
It can relieve fatigue from the neck to the ankles in a
short time.
A program to relieve the whole body with the unique
functional core shiatsu method.
(DC-001 is the traditional shiatsu method)
By shiatsu, gently rubbing the acupoints inside the body.
A program to alleviate general fatigue.
From the root of the neck to the ankle, gently rubbing
the acupoints of the whole body without omission.
Circulation promotion: a program that focuses on
promoting blood circulation.
Starting from the bottom of the body to the heart and
by using the method of massaging muscles while promoting
blood circulation to achieve the effect of promoting blood
circulation.
According to the centripetal method of promoting blood
flow from the fingertips and toes back to the heart,
massages along the venous flow.
This program is recommended when you want to relax
and revive your body.
According to the centrifugal method of promoting blood
circulation from the heart to the tips of the body,
massages along the artery flow.
This program is recommended when you want to relax.
Quick Program
Master Shiatsu Program
Restore Program
/
The name and operation
※
depend on the model
Recovery Program
Circulation Program
Morning Program
Night Program
~
10 minutes
~
30 minutes
~
15 minutes
~
15 minutes
~
15 minutes
~
15 minutes
17
Neck & Shoulders
Program
Lower Back Program
Air Focus Program
~
10 minutes
~
10 minutes
~
10 minutes
Massage neck stem, neck, upper shoulders and shoulders.
This program is recommended for neck and shoulder
fatigue and for relaxing the neck and shoulders.
A program for centralized massaging of the low back and
waist. This program is recommended when the lower
back is tired and for relaxing around the lower back.
A program for centralized massaging of the ends of the
body, such as the fingertips and toes.
Promote systemic blood circulation by stimulating the
ends of the body.
【Manual programs】
Manual programs allow you to freely combine the functions you like such as Knead and
Tap. Within these functions one can also adjust the speed, strength, up and down
positioning, and other massage movements.
Page 19
POWER
Shiatsu
Knead
Shiatsu
3D
Intensity
Roller
Heat
Leg & Foot
Arm
Massage
Massage
Shiatsu
Quick
Recovery
Morning
Night
Air Focus
Roller
Auto/Manual
Width
EMERGENCY
STOP
Circulation
Neck &
Shoulders
Air
Intensity
Back
Speed
Speed
Auto Programs
Manual Programs
Left
Center
Right
Down
Up
Full
Upper
Lower
Wide
Mid
Narrow
Back
Leg
Auto Programs
3D
Intensity
Heat
Air
Intensity
Massage with Auto programs
●Equipped with nine programs that can relieve fatigue and improve physical function.
●To begin an auto program, simply press the button of the program desired.
①
①
Press the [Power] button.
If the chair has been inactive for 90 minutes, the
remote power will automatically turn off.
②
Press the desired [Auto program] button.
The chair will automatically reline and the
acupoint search will begin (you will hear a slow
Master
beep at the end of this process).
【Notice】
Please sit fully in the chair and rest your head on
②
Lower
③
the back of the pillow in a comfortable position.
When the body is lifted, the acupoints cannot be
correctly searched.
③
Shoulder position can be adjusted.
Once your shoulders have been detected you will
hear a beeping noise. During this time, the
shoulder position can be fine-tuned, if necessary,
using the roller adjustment buttons. Upon completion of this process, the selected auto program
will begin.
【Shoulder position adjustment】
If the shoulder position is inconsistent, adjust the
shoulder position after the beepinｇ.
Knead
Tap
Balance
Range
High
Appropriate location
Low
Roller
By pressing it,
the massage
wheel continues
upwards
By pressing it,
the massage
wheel continues
downwards
④The program starts to run.
After searching for the acupoints, the buzzer will
stop and the program will begin. The intensity of
the massage device or air pressure can be adjusted
The remote control varies with the model
※
of machine.The illustration is DC-100A.
Massage Intensity Adjustment and Heater Temperature Adjustment and Cancel
It can adjust the intensity of the massage and the temperature of the heater.
Each time the 3D button and Air Intensity buttons are pressed, they can be switched in the
order of strong→weak→medium. (The default setting is medium when the program starts
running.)
Each time the heating button is pressed, it can be switched in the order of weak→strong→
off. (The default setting is off when the program starts running.)
during the operation of the program.
【Auto Programs】
18
Page 20
【Auto Programs】
⑤The program ends.
The massage wheel returns to the storage position and switches to standby mode.
Thereafter, you can select the mode you like.
● Please turn off the power of remote control after the massage.
Change program
It is not necessary to wait for the program to finish. It is feasible to switch to a different
program while one is running. In addition, even if the massage program is running, if the
running time exceeds 90 minutes, the massage will automatically end.
Auto program →Auto program
When the auto program is running, press the other auto program buttons,
then the massage wheel will return to the detected shoulder position, and starts after
reconfirming the shoulder position. Shoulder position can be fine tuned when reconfirming
shoulder position.
Auto program →Manual program
When the auto program is running, press the mode selection button to interrupt the
auto massage. You can then select the program you desire. Massage motion will begin
immediately after the press of a button.
Halfway end program
To interrupt the program, press the [Power] button when running. The massage wheel
will stop running after the massage mechanism has moved to its storage position.
In case of an emergency or abnormal operation of the massage chair, please press the
button [EMERGENCY STOP], to stop the massage chair immediately. After confirming
it is safe, press the [Power] button. The massage mechanism will move to its storage
position and the chair will incline for your safe exit.
When selecting a program, automatic tilting may occur in the automatic program. In
addition, automatic tilting may occur when the program is running. So before using,
please make sure there are no people or obstacles behind the chair. Also, when using,
please keep other people away from the massage chair when you are using it.
●
If you feel that the massage is too stimulating, please reduce the stimulation according to this manual. If the stimulation is still too strong
after the adjustment, please stop using it and contact the dealer
(recorded at the bottom of the cover).
→
If you feel too stimulating but continue to use it, it may lead to injury.
●
Do not put your hands and feet in the movable parts such as the upper
and lower parts of the massage wheel, the back of the chair, etc.
Caution
In addition, do not wear hair accessories, necklaces, watches, bracelets,
rings or other hard objects when using the chair.
●
During a massage, if the legs are pulled out of the leg component, do not
force the legs back in.
●
Total massage time should not exceed 60 minutes per day. Massages
should be taken in intervals of 90 minutes or less, with significant
breaks between sessions. Do not massage any one area continuously for
more than 5 minutes at a time.
→
Long-term continuous use may cause excessive stimulation, resulting in adverse
effects or injuries.
19
Page 21
POWER
Shiatsu
Knead
Shiatsu
3D
Intensity
Roller
Heat
Leg & Foot
Arm
Massage
Massage
Shiatsu
Quick
Recovery
Morning
Night
Air Focus
Roller
Auto/Manual
Width
EMERGENCY
STOP
Circulation
Neck &
Shoulders
Air
Intensity
Back
Speed
Speed
Auto Programs
Manual Programs
Left
Center
Right
Down
Up
Full
Upper
Lower
Wide
Mid
Narrow
Back
Leg
Manual Programs
Operation and adjustment methods of each part
① ②
Master
Lower
①
Press the [Power] button.
If the chair has been inactive for 90 minutes, the
remote power will automatically turn off.
②
Press the mode selection button.
If you press the mode selection button, you can
change from an auto program to a Manual program.
③
Press the desired Manual program button.
【Manual Programs】
Please select the mode you like from the combination of basic actions, such as rolling, special
action and air pressure massage.
④
Program starts to run.
During the massage, intensity can be adjusted and
air massage can be stopped.
⑤
Program ends.
The massage wheel returns to the storage
position and switches to standby mode. Thereafter, you can select the mode you like.
●
Knead
Tap
③
Please turn off the power to the remote
control after the massage.
Balance
Range
The remote control varies with the model
※
of machine.The illustration is DC-100A.
Shoulder Position Adjustment
【When selecting an operation
that the roller doesｎ’t move】
Roller
Adjust the position of the
massage wheel to the place
where you want to massage.
When the massage wheel reaches the top (bottom) limit, a beep warning will sound if user
●
presses the roller up (down) button.
By pressing it, the massage wheel continues upwards
By pressing it, the massage wheel continues
downwards
20
Page 22
Width adjustment
Width
Wide
Mid
Narrow
Speed
Speed
Shiatsu
Left
Center
Right
3D
Intensity
Heat
Air
Intensity
The width of the massage wheels can be switched from narrow→medium→wide.
(The default setting is narrow when the program starts running.)
【Manual Programs】
21
Knead
Tap
The speed of massage motions can be adjusted in 3 levels. (The default setting
is slow speed when the program starts running.)
Adjusting Shiatsu balance
Speed adjustment
Balance
During this program, the balance of the finger pressing can be switched in the order
of left strengthening, left and right strengthening, or right strengthening. (The
default setting is left and right with simultaneous strengthening at the
beginning of the shiatsu.)
Massage Intensity Adjustment and Heater Temperature Adjustment and Cancel
Press the 3D and/or Air Intensity buttons to adjust strength of the massage.
They can be adjusted between Strong, Medium and Weak. The default setting is
Medium.
Press the Heat button to activate/deactivate heat. It can be adjusted between
Low and High temperatures. The default setting is off.
Change program
It is not necessary to wait for the program to finish. It is feasible to switch to a different
program while one is running. In addition, even if the massage program is running, if the running
time exceeds 90 minutes, the massage will automatically end.
Manual program →Auto program
When the manual program is running, press the mode selection button to interrupt the
manual massage. You can then select the program you desire. Massage motion will begin
immediately after the press of a button.
Halfway end program
To interrupt the program, press the [Power] button when running. The massage wheel will
stop running after the massage mechanism has moved to its storage position.
In case of an emergency or abnormal operation of the massage chair, please press the
button [EMERGENCY STOP], to stop the massage chair immediately. After confirming it is
safe, press the [Power] button. The massage mechanism will move to its storage position
and the chair will incline for your safe exit.
If you feel that massage is too stimulating, please reduce the stimulation according to
●
this manual. If the stimulation is still too strong after the adjustment, please stop
using it and contact the dealer (recorded at the bottom of the cover).
→If you feel too stimulated but continue to use it, it may lead to injury.
●
Do not put your hands and feet in the movable parts such as the upper and lower parts
of the massage wheel, the back of the chair, etc.
In addition, do not wear hair accessories, necklaces, watches, bracelets, rings and
Caution
other hard objects when using.
●
When massaging the legs, if legs are removed, do not force the legs back
into the legrest when a massage is in progress.
Total massage time should not exceed 60 minutes per day. Massages should be taken in
●
intervals of 90 minutes or less, with significant breaks between sessions. Do not
massage any one area continuously for more than 5 minutes at a time.
Long-term continuous use may cause excessive stimulation, resulting in adverse effects or
→
injuries.
Page 23
Troubleshooting
If any abnormalities remain after the following checks, please stop using immediately to
prevent accidents. Unplug the chair, and contact the dealer.
Causes and remediesState
construction is not a malfunction.
it immediately.
The massage wheel
positions of the left
and right massage
devices are deviated.
The massage wheel
stopped halfway while
massaging.
Some basic work and
special actions can not
be started.
The use of alternating finger
pressure structures and
alternating thumping structures
is an inevitable phenomenon in
construction. This is not a
malfunction.
When excessive force is applied to the
massage wheel, it may stop running. Please
keep your body slightly raised or gently
incline the massage chair back before use. If
too much weight is on the back, this is not a
malfunction.
Please turn off the main power switch behind
the massage chair. Turn on again after about
5 seconds.
The inevitable phenomenon in
【Troubleshooting】
If there is any abnormality after check, please stop using
Innacurate shoulder
pressure acupoint
detection. (The location
of the massage wheel is
not stopping at the top
of my shoulder)
After pressing the
remote control button,
it still can't work
properly. Or you can't
turn on the power.
The power cord and
plug are abnormally hot.
Please sit back completely in the chair and
rest your head on the cushion. After
detecting the acupressure, immediately
press the shoulder adjustment button to
adjust the shoulder position.
Please make the following checks.
Is the power plug fully plugged into the
①
socket?
Is the main power switch behind the
②
massage chair turned on?
Do you press two buttons at the same
③
time?
Stop using it immediately.
●Do not allow non-service personnel to disassemble or repair it.
●Please contact the sales store or dealer (recorded at the bottom of the cover) .
22
Page 24
Running
sound
When running, the following running sounds will be emitted.
A sound accompanied by a thump
Friction sound between massage
wheel and cloth during kneading
Sound of massage wheels lifting,
kneading and finger pressing
The sound of air pressure massage
Grunting
Whizzing
Squeaking
Buzzing
Rattling
Air pump sound
Pounding
【Troubleshooting】 【Safty Inspection】
Exhaust sound of airbag
The sound of the chair back
tilting up and down
※ The above-mentioned sounds will not affect the performance
of the chair, and are considered normal.
Pinging
Buzzing
Safety Inspection
It’s important to periodically inspect your massage chair to ensure it’s safe for
use, especially after not using it for a long period of time.
Please inspect your chair to confirm the
following is not observed:
After pressing a button, the chair does
●
not perform the desired movement.
● The power cord is cracked or damaged.
The power cord and/or plug are
●
abnormally hot.
●
There is a burning smell coming from
the chair.
When the chair is running, it vibrates
●
and makes abnormal sounds and/or
vibrations.
●
The timer cannot be automatically
turned off.
●
Other abnormalities or malfunctions
occurred.
If you are
experiencing any of
the situations as
described on the
left, in order to
avoid malfunction
or accident, please
stop using the
chair, immediately
unplug the power
plug from the
outlet, and contact
your dealer
(recorded at the
bottom of the
cover).
Warm tips
Caring test
23
Page 25
FAQs
Can I place the massage
chair on an electric carpet?
No, since the massage chair
is heavy, it may damage the
heating body of the electric
blanket and cause fire.
Therefore, do not place it
on an electric heating
carpet.
Can it be placed on the
wooden floor or radiant
heating floor?
Yes.
however, it is recommended to
place the massage chair on the
carpet as it may damage the floor.
How do I enhance the intensity
of the massage?
Please try the following:
Sit back fully and put your
●
weight competely on the
back of the chair.
●
Set the device strength to
"strong" by using the [3D
Intensity] button.
●
Fully recline the backrest.
How do I reduce the intensity
of the massage?
Please try the following:
Set the device strength to
●
"weak" by using the [3D
Intensity] button.
Place the extra cushion on
●
the back or seat.
Incline the backrest.
●
What should I do if I spill
water carelessly?
It may lead to an electric
shock. Please stop using it
immediately and do the
following.
●
Turn off the power switch
behind the massage chair.
●
Unplug the power plug form
the socket.
After the above operations,
please contact the sales store
or dealer (recorded at the
bottom of the cover).
Will the back of the chair
automatically incline at the
end of the program?
No, when the power is
turned off, it will not reset
automatically at the end of
the program.
But when the power
is turned off or the overuse
timer is activated, the back of
the chair will automatically
incline.
What is the recommended
height limit?
150 cm - 180 cm.
(59 inch - 71 inch.)
What is the maximum user
weight?
100 kg.(220 lbs.)
︻
FAQs
︼
24
Page 26
Care and Storage
Method of cleaning and maintenance
●
Caution
【Cleaning and Maintenance of Upholstered Elements】
When stained, soak a soft cleaning cloth in warm water with a small amount of
neutral detergent, wring it out, and then wipe.
Caution
【Cleaning and Maintenance of Plastic Parts】
Soak the soft cleaning cloth in warm water containing a small amount of
neutral detergent. Wring it out and then wipe it. To avoid residual detergent,
【Care and Storage】
please wipe it with dry cloth again.
●
Do not use alcohol, other solvents and polishing powder for cleaning and maintenance, otherwise it may lead to scratches, discoloration and cracks.
Applicable items Inapplicable items
Water
【Cleaning and Maintenance of Wooden Panel, Wooden Railings and Remote Control】
Please wipe the dirt from the wooden panel, wooden railings and remote control
with dry cloth.
●Do not wipe with a wet towel.
→ Otherwise, it may lead to malfunction.
●
Warm water
Neutral
detergent
Be sure to unplug the power plug from the socket before cleaning and
maintenance. In addition, do not plug or unplug the power cord with
wet hands.
Contact with plastic and indoor wallpaper for a long time may cause
discoloration.
Other
solvents
Alcohol
+
Diluent
Polishing powder
25
Storage method
●After decontamination and dust removal, place it in a dry place.
●When not in use, cover with a dust-proof cover to avoid dust.
●
In order to prevent pets from gnawing the power cord, please keep pets away
from the machine during storage.
●
Caution
Do not place the machine in direct sunlight or near areas of high
temperature such as heating appliances.
Page 27
After sales service
1. Warranty Card
Please be sure to ask for a warranty card from the sales store or dealer at the time of
purchase and confirm that the purchase date, store name, and other items are completed.
Please read the warranty carefully and keep it properly. (Show it when repairing. ) The
warranty period is recorded on the warranty card. However, this product is specially
designed for the country you purchased, so when used abroad, the warranty card will not
be valid even during the warranty period. In addition, when it is used for other purposes
than general household use, the relevant repair costs will be paid even during the
warranty period.
2. When commissioning repairs
Before commissioning the repair, please read carefully the "Troubleshooting Guide" on
page 22 in advance. If there are any abnormalities after the check, please contact the
sales store to commission the following matters.
1) Name, address, telephone number
2) Name and model of the product...
Please refer to the specifications column on
page 27 of this manual, or the company sign
attached to the cover of the chair base.
3) Production No....
Please refer to the company sign attached to
the cover of the chair base.
4) Date of purchase
5) Malfunction status
(Please inform as much as possible in detail. )
Model
Company sign
Production
No.
【After sales service】
● During the warranty period
When repairing, please show your warranty card. Since repairs may be paid even during
the warranty period, please read the warranty card carefully.
● Over the warranty period
Please contact the sales store where you purchase this product. If the performance of
the product can be maintained through maintenance, it can be repaired according to
customer needs.
● When you can't commission a sales store
Please contact the dealer (recorded at the bottom of the cover).
● Minimum Retention Period of Performance Parts for Maintenance
The company will retain the maintenance performance parts of the electric massager
for at least 6 years after the end of production. (Except for sewing and wood
products.)
Maintenance performance parts refer to the parts necessary to maintain the performance
of the product.
● If you have any questions about after-sales service
Please consult the sales store or dealer (recorded at the bottom of the cover).
●
Repair may be refused in countries other than the country where the product is
purchased.
26
Page 28
Specification
Model DC-1000A DC-100A DC-001A
Power supply AC120V
Rated power 150W
【Specification】
Rated Frequency
60Hz
Rated time 90 minutes
Kneading speed
Tapping speed
Shiatsu speed
Up and down speed of massage wheel
Minimum of 21 times / minute
Maximum of 27 times / minute
Minimum of 400 times / minute
Maximum of 700 times / minute
[Back]
Maximum 33 times / minute
[Arm]
Maximum 36 times / minute
[Leg]
Maximum 34 times / minute
[Foot]
Maximum 34 times / minute
3 cm/ second (1.2 inch/ second)
Massage range 90 cm (35.4 inch)
Massage wheel push-out range
7 cm (2.8 inch)
Air pressure 37kPa
Heater Below 45°C N / A
Auto programs 9 kinds
Manual programs 6 kinds 5 kinds
Program timer 10-30 minutes
Overuse timer
Tilt angle
Dimensions
Weight
Outer fabric Synthetic leather
90 minutes (continuous operation)
No grade (electric tilt) about 113-145°relative to
the horizontal plane
Width 94 cm x Length 149 (184) cm x Height 126 (94) cm
(Width 37 inch x Length 58.6 (72.4) inch x Height 49.6 (37) inch)
The number in the bracket is the length and heightof the
maximum tilt angle
135 kg (297 lbs) 125 kg (275 lbs)
Synthetic textile
[Foot]
Maximum
34 times /
minute
27
Accessories
Power cord, remote control bracket, cushion pad
Packaging 2 packs / 1 set
Page 29
282930
Page 30
Page 31
Page 32
DC-1000A
DC-100A
DC-001A
Made in Japan
Made in China
Manufactured by NIN Co., Ltd.
Postal Code: 108-0074,
No.2-15-11 Takanawa,
Minato-ku, Tokyo, Japan
Date of issue:June,27,2019
*************
Loading...