3/98 revised 11/02 Form Number 56041404
A-English
B-Deutsch
C-Français
D-Nederlands
Whirlamatic™ 2700
Advance MODEL 56420000
Nilfisk MODEL 56420161
Instructions For Use
Bedienungsanleitung
Mode d' emploi
Gebruiksaanwijzing
BHS 7014
A-2 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-2 / ENGLISH
TABLE OF CONTENTS
Page
Introduction .......................................................................................... A-2
Parts and Service.................................................................................A-2
Nameplate............................................................................................A-2
Uncrating the Machine .........................................................................A-2
Important Safety Instructions ............................................................... A-3
Know Your Machine ................................................................... A-4 – A-5
Preparing the Machine for Use
Installation of The Battery Pack ........................................................... A-6
New Battery Pack Set-Up .................................................................... A-6
Installation of The Burnishing Pad ....................................................... A-8
Installation of The Dust Collection Bag ................................................A-8
Operating the Machine
Before Each use ..................................................................................A-8
Plan Your Floor Burnishing ..................................................................A-8
Operating The Machine .......................................................................A-8
After Use .............................................................................................. A-9
Maintenance
Maintenance Schedule ........................................................................A-9
Battery Maintenance ............................................................................A-9
Lubricating The Machine ......................................................................A-9
Chain Tension For Steering And Drive .............................................. A-10
Foot And Parking Brake .....................................................................A-10
General Machine Troubleshooting
Operator Display Panel Overload Indicators......................................A-11
Operator Display Panel Status Lights ................................................A-11
Swirl Marks ........................................................................................A-11
Circles on the Floor ............................................................................A-11
Floor Finish Removed ........................................................................A-11
Machine Wobbles During Operation .................................................. A-11
Machine Does Not Run ......................................................................A-11
Technical Specifications ....................................................................A-12
INTRODUCTION
This manual will help you get the most from your Nilfisk-Advance Whirlamatic 2700 / BHS 7014. Read it thoroughly before operating the machine.
Note: Bold numbers in parentheses indicate an item illustrated on pages A-4 – A-5.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by Nilfisk-Advance service personnel using Nilfisk-Advance original replacement parts and accessories.
Call Nilfisk-Advance for repair parts or service. Please specify the Model and Serial Number when discussing your machine.
NAME PLATE
The Model and Serial Number of your machine are shown on the Nameplate on the machine. This information is needed when ordering repair parts for the machine.
Use the space below to note the Model and Serial Number of your machine for future reference.
MODEL
SERIAL NUMBER
UNCRATING
When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a freight damage claim.
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - A-3
ENGLISH / A-3
IMPORTANT SAFETY INSTRUCTIONS
This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other than
normal residential housekeeping purposes.
Read all instructions before using.
WARNING!
To reduce risk of fire, electric shock, or injury:
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• This machine shall be used only by properly trained and authorized persons.
• This machine is for dry use only and shall not be used or stored outdoors in wet conditions.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Keep sparks, flame and smoking materials away from batteries. Explosive gases are vented during normal operation.
• Charging the batteries produces highly explosive hydrogen gas. Charge batteries only in well-ventilated areas, away from open
flame. Do not smoke while charging the batteries.
• Remove all jewelry when working near electrical components.
• Turn the key switch off (O) and disconnect the batteries before servicing electrical components.
• Never work under a machine without safety blocks or stands to support the machine.
• Do not dispense flammable cleaning agents, operate the machine on or near these agents, or operate in areas where
flammable liquids exist.
• Do not clean this machine with a pressure washer.
• This machine is not approved for use on public paths or roads.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may
reduce air flow.
• Do not operate this machine on ramps or inclines of more than 5 degrees.
• When operating this machine, ensure that third parties, particularly children, are not endangered.
• Before performing any service function, carefully read all instructions pertaining to that function.
• Do not leave the machine unattended without first turning the key switch off (O), removing the key and applying the parking
brake.
• Turn the key switch off (O) before changing the pad, and before opening any access panels.
• Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.
• Do not use without dust bag and / or filters in place.
• Do not stand on the pad housing.
• This machine is not suitable for picking up health endangering dust.
• The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries should be
safely done in accordance with your local environmental regulations.
SAVE THESE INSTRUCTIONS
A-4 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-4 / ENGLISH
1 Pad Motor Deck
2 Dust Control Shroud
3 Burnishing Pad
4 Pad Retainer
5 Dust Collection Bag
6 Machine Tie Down
7 Battery Pack Connection
8 FWD / REV Drive Pedal
9 Tilt Steering Wheel Adjuster
10 Emergency Power Disconnect
11 Steering Wheel
12 Horn Switch
13 Parking Brake Set / Release Lever
14 Brake Foot Pedal
15 Operator Seat W / Safety Switch
16 Machine Battery Charger Port
17 Battery Access Door
18 Drive Wheels
19 Steer Wheels
20 Circuit Breakers
40 Amp (Drive Motor)
5 Amp (Control Circuit)
21 Battery / Controller Compartment Cover
22 Prop Rod
23 Seat Adjuster
6
9
12
15
19
21
23
1
2
3
4
6
18
20
KNOW YOUR MACHINE
Control Panel
24 Main Power Switch
25 Main Power Ind. Light (green-OK / red-fault)
26 Hourmeter / Pad Drive Error Display
27 Speed Control Status Ind. Light (green-enabled)
28 Drive Motor Overload Ind. Light
29 Lift Motor Overload Ind. Light
30 Pad Motor Overload Ind. Light
31 Battery Condition Indicator Lights
32 Pad Down Ind. Light (green-down & Pad ON / yellow-down & Pad
OFF)
33 Pad Lift Raise / Lower Switch
34 Pad Up Ind. Light (green-up & enabled / red-up & disabled)
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - A-5
ENGLISH / A-5
5
6
6
7
8
10
11
13
14
16
17
22
27
28
29
30
31
32
33
34
24
25
26
KNOW YOUR MACHINE
CONTROLPANEL
A-6 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-6 / ENGLISH
INSTALLATION OF THE BATTERY PACK
WARNING!
Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or
eyes. Explosive hydrogen gas is vented from inside the batteries through openings in the battery caps. This gas can be ignited by
any arc, spark or flame.
WHEN SERVICING BATTERIES...
• Remove all jewelry
• Do not smoke
• Wear safety glasses
• Work in a well-ventilated area
• Do not allow tools to touch more than one battery terminal at a time
CAUTION!
Acid can spill onto the floor if the batteries are overfilled.
To avoid damage to floor surfaces, wipe water and acid from the top of the batteries after charging.
Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly. Batteries should be installed by your
local Nilfisk-Advance Distributor or by a qualified electrician.
NEW BATTERY PACK SET-UP
1 See Figure 1. Pull the Battery Tray (A) and the Battery Box (B) out of the machine chassis and center the assembly on a pallet jack with the side rails
of the Battery Box (B) parallel to the pallet jack forks. IMPORTANT: The Battery Box (B) must be on the pallet jack before placing the batteries in the
Battery Tray, or you will not be able to get a pallet jack under the Battery Box. NOTE: A 27" (68 cm) or narrower pallet jack is required, a pallet jack any
wider will not work!
2 Place the batteries into the Battery Tray and connect the Battery Cables (C) as shown. Connect the Connector Assembly (D) as shown (black cable to
negative terminal / red cable to positive terminal).
3 Install the Battery Post Boots (E). Secure tightly to battery cables with supplied tie straps.
4 Raise the jack until the battery box will clear the side rails in the chassis and then roll the battery box into the battery compartment until it contacts the other
side of the chassis and then lower it onto the side rails in the chassis.
5 Connect the Battery Pack Connection (7). Open the Battery / Controller Compartment Cover (21) to provide proper ventilation.
6 Push the connector from the charger into the Machine Battery Charger Port (16). Follow the instructions on the battery charger.
7 Check the fluid level in all battery cells after charging the batteries. Add distilled water, if necessary, to bring the fluid level up to the bottom of the filler
tubes.
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - A-7
ENGLISH / A-7
FIG. 1
Pallet Jack Forks
Gabel n des Palettenhebers
Fourchettes du chevalet de palette
Vorken van het hefplatform
A
B
C
D
E
Chassis Side Rails
Seitenschienen des Chassis
Rails de côté du châssis
Zijschuiven van het onderstel
Battery Box Side Rails
Seitenschienen des Batterietroges
Rails de côté de la boîte de batterie
Zijschuiven van de accubak
A-8 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-8 / ENGLISH
INSTALLATION OF THE BURNISHING PAD
WARNING!
Disconnect the machines Battery Pack Connection (7) by pushing
in the red knob on Emergency Power Disconnect (10), when ever
servicing the machine.
1 Place your hand underneath the pad motor Dust Control Shroud (2) and
remove the Pad Retainer (4) from the flexible pad holder assembly.
NOTE: Grip the retainer firmly and turn clockwise (to the right) as the
retainer uses a Left Hand thread.
2 Select a 27 inch (68 cm) Dia. burnishing pad. See your local Nilfisk-
Advance Distributor for a complete selection of pads and accessories.
3 Insert the plastic Pad Retainer (4) into the center of the pad. Then
reinstall by turning the retainer Counter clockwise (to the left). NOTE:
Important !!! Turn the retainer in until you hear a clicking ratchet sound,
this insures proper tightening of the pad by properly compressing the
pad material and drawing up the retainer so it will not strike the floor.
INSTALLATION OF THE DUST COLLECTION
BAG
The WHIRLAMATIC 2700 / BHS 7014 uses dust collection bag PN 56391185
(sold 6 to a Pkg.).
Unfold the Dust Collection Bag (5) and while holding onto the card board retainer
insert it over the collection tube found on the top of the Pad Motor Deck (1).
NOTE: Never operate the WHIRLAMATIC 2700 / BHS 7014 with out a Dust
Collection Bag (5) installed. Failure to do so will allow the burnishing dust to
become airborne.
BEFORE EACH USE:
1 Be sure you understand the operator controls and their function.
2 Turn the Main Power Switch (24) ON (l) and check the Battery Condition
Indicator (31). If red light comes on, recharge the battery pack before
using the machine
3 Check the Brake Foot Pedal (14) for proper operation.
4 Check that a new or clean pad has been installed.
5 Check that a Dust Collection Bag (5) is installed.
PLAN YOUR FLOOR BURNISHING:
1 Pre-sweep or scrub floor area of debris to prevent scratching and poor
burnishing performance.
2 Arrange long runs with a minimum of stopping or starting.
3 Avoid bumping into posts or scraping the side of the machine.
OPERATING THE MACHINE
NOTE: Bold numbers in parentheses indicate an item shown on pages A-4 –
A-5.
Follow the instructions in preparing the machine for use and the pre-operational
check list section of the manual.
1 While seated on the machine adjust the Seat (15) and the Steering
Wheel (11) using the Adjustment Controls (23) and (9), to a comfortable
operating position.
2 Turn the Main Power Switch (24) ON (l). This will display the Main
Power Ind. Light (25), Battery Condition Indicator Light(s) (31) and
Hourmeter (26).
3 Release the Parking Brake Set / Release Lever (13) by pushing the
Brake Foot Pedal (14). To transport the machine to the work area, apply
even pressure on the front of the FWD / REV Drive Pedal (8) to go
Forward or the rear of the pedal for Reverse.
4 When at the work area press the machine’s FWD / REV Drive Pedal (8)
to move the machine in either FWD or REV drive. The machine should
always be moving before lowering the Pad Motor Deck.
5 Once the machine is moving, lower the Pad Motor Deck (1) by pressing
the Pad Lift Raise / Lower Switch (33) to the right. The Pad Down Ind.
Light (32) on the control panel will light yellow when going down and
then turns green to confirm the lowered position and the pad begins to
turn. To raise the pad motor press the Pad Lift Raise / Lower Switch (33)
to the left. The Pad Up Ind. Light (34) will be red when coming up and
then turns green to confirm the raised position. NOTE: When the
operator’s foot is removed, the drive pedal automatically returns to
neutral and the pad motor will shut off after 1.5 sec (the Pad Down Ind.
Light (32) will light yellow). Raise the Pad Motor Deck before stopping
the machine. The floor may be damaged if the machine is stopped with
the pad down and running.
6 Begin burnishing making long straight line passes, overlap each pass
2-3 inches (5-7 cm). Adjust your machine speed according to the
condition of the floor (if the floor is heavily scuffed, drive at a slower rate
to ensure proper burnishing).
CAUTION!
The floor may be damaged if travel of the machine is stopped with
the pad down and running.
7 It may become necessary when burnishing to stop the machine, raise
the pad and check to see if the pad is loaded up with floor finish and dirt.
If it is, turn the pad over to expose the clean side, or install a clean pad.
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - A-9
ENGLISH / A-9
AFTER USE
1 Raise the Pad Motor Deck (1), then drive the machine to a service area.
2 Turn the Main Power Switch (24) OFF (O) and remove the key.
3 Press down on the Brake Foot Pedal (14) and set the parking brake by pushing forward on the Parking Brake Set / Release Lever (13).
4 Remove the burnishing pad, rinse the pad with warm water and hang it up to dry. NOTE: Allow pad to dry completely before using again.
5 Check the Dust Collection Bag (5) if over half full or damaged remove and replace with a new bag.
6 Check the maintenance schedule and perform any required maintenance.
7 Wipe the machine with a damp cloth, then store the machine in a clean, dry place.
MAINTENANCE SCHEDULE
MAINTENANCE ITEM Daily Weekly Monthly Yearly
Charge Batteries •
Check/Clean/Replace Burnishing Pad •
Check/Replace Dust Collection Bag •
Check Battery Water Level(s) •
Check/Replace Pad Shroud Skirt •
Check Foot/ Parking Brake For Wear & Adjustment •
Check Tire Pressure (50 PSI) •
Chain Tension - Steering and Drive •
Lubrication - Grease Fittings •
Check Pad Motor Belt Wear & Tension •
Check Carbon Brush Wear On Pad/Drive/ Actuator Motors •
NOTE: Refer to the Service Manual Form No. 56043042 for more detail on all maintenance items mentioned in this manual.
BATTERY MAINTENANCE
Charge the batteries each time the machine is used for 1 hour or longer, or whenever the Battery Condition Indicator Lights (31) light up red.
To Charge the Batteries...
1 Open the Battery / Controller Compartment Cover (21) to provide proper ventilation.
2 Push the connector from the charger into the Machine Battery Charger Port (16) on the side of the machine.
3 Follow the instructions on the battery charger.
4 Check the fluid level in all battery cells after charging the batteries. Add distilled water, if necessary, to bring the fluid level up to the bottom of the filler
tubes.
CAUTION!
Acid can spill onto the floor if the batteries are overfilled.
To avoid damage to floor surfaces, wipe water and acid from the top of the batteries after charging.
LUBRICATING THE MACHINE
Once a month pump grease into each grease fitting (zerk) on the machine (total of 10) until grease seeps out around the bearings.
Grease fitting locations are:
Qty 1 - Steering Wheel Shaft Universal Joint
Qty 3 - Drive Wheel Differential Bearings
Qty 1 - Rear Steering Spindle Bearing
Qty 3 - Rear Steering Chain Sprocket Bearings
Qty 2 - Rear Wheel Hub Bearings
A-10 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-10 / ENGLISH
CHAIN TENSION FOR STEERING AND DRIVE
Figure 2 shows the steering chain routing for both the upper and lower chains. Inspect once a month and make adjustments if needed (refer to the service manual
for detailed instructions).
To check or adjust the drive motor chain refer to the Service Manual (form # 56043042) for detailed instructions or have a qualified Nilfisk-Advance Dealer
Technician perform this maintenance function.
FIG. 2
FOOT AND PARKING BRAKE
Check weekly for proper machine braking performance and the stationary parking brake function. The adjustment for the foot brake is made by turning the pedal
rod linkage turnbuckle.
Upper Chain
Obere Kette
Chaîne Haute
Bovenste Ketting
Lower Chain
Untere Kette
Chaîne Basse
Onderste Ketting
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - A-11
ENGLISH / A-11
GENERAL MACHINE TROUBLESHOOTING
OPERATOR DISPLAY PANEL OVERLOAD INDICATORS:
There are (3) overload indicator lights, refer to the illustrations on pages (A-4 – A-5) for their locations.
Drive Motor Overload: This indicator (28) will flash RED along with the Main Power Indicator Light (25) if the wheel drive circuit breaker trips (Drive motor stops
running). To clear, turn key switch (24) off and determine and correct the cause of the overload. Then reset the 40 Amp circuit breaker (20). NOTE: In addition,
the Speed Control Status Indicator Light (27) will flash a green fault code (see Speed Control Status Light section below).
Lift Motor (Actuator) Overload: This indicator (29) will flash RED along with the Main Power Indicator Light (25) if a motor over load occurs. To clear, turn key
switch off, determine and correct the cause of the overload. Then turn key switch back on.
Pad Motor Overload: This indicator (30) will flash RED along with the Main Power Indicator Light (25) if a motor over load occurs. To clear, turn key switch off,
determine and correct the cause of the overload. Then turn key switch back on.
OPERATOR DISPLAY PANEL STATUS LIGHTS:
Speed Control Status Light: This indicator (27) will light GREEN when there is power applied to the control circuit of the speed controller (normal function). Note:
For the indictor to function the operator must be on the seat so that the seat switch is closed. The indicator will flash a diagnostic fault code to signal a drive controller
function problem. Have a qualified service mechanic refer to the machine service manual for explanations of the fault codes and corrective action for drive system
troubleshooting and repair.
Main Power Indicator Light (25) and Main Controller Fault Display (26): With the key turned on a GREEN light indicates the main controller system is ready.
A Green flashing indicator light shows that the key is turned off but the main controller is still maintaining power until the burnishing deck is automatically raised
to its full up position (normal function). When the light reads RED the pad motor well not function and at the same time an error code is displayed on the Hour
meter/Fault Display (26). This confirms a system error has occurred, the error display will read “Err” followed by a two digit code(s). Reference the Service Manual
for fault code descriptions and corrective action.
SWIRL MARKS
• Floor not clean.
• Area not properly swept - debris in pad or brush.
• Improper pad for the job.
• Moving the machine too fast.
CIRCLES ON THE FLOOR
• Machine standing still while the pad is running.
FLOOR FINISH REMOVED
• Improper pad...too aggressive.
• Moving the machine too slowly.
MACHINE WOBBLES DURING OPERATION
• Defective pad... one side is more dense than the other.
• Pad not “seated” properly into pad holder bristles.
• Padholder out of balance - replace.
MACHINE DOES NOT RUN
• Check Emergency Power Disconnect (10)
• Check Battery Charger Port interlock switch (16)
• Check operator seat safety switch (15)
• Check for error fault codes in both the main and speed controllers (see service manual)
• Foot Pedal Fault : Caused by the operator activating the FWD / REV Drive Pedal (8) before turning on
the Main Power Switch (24). To Clear: Turn the key switch off, wait until display is off, then turn key switch back on.
A-12 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
A-12 / ENGLISH
TECHNICAL SPECIFICATIONS (as installed and tested on the unit)
Model Whirlamatic™ 2700 / BHS 7014
Model No. 56420000 / 56420161
Current A 160
Voltage, Batteries V 6 x 6V/36V
Battery Capacity Ah 395
Protection Grade IP 30
Sound Power Level (ISO 3744) dB(A)/20µPa <72.5
Net Weight (w/o batteries) lbs/kg 580 / 263
Gross Weight (w/batteries) lbs/kg 1,300 / 590
Vibrations at the Hand Controls m/s
2
<2.5m/s
2
Vibrations at the Seat m/s
2
<0.5m/s
2
B-2 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
B-2 / DEUTSCH
INHALTSVERZEICHNIS
Seite
Einleitung ............................................................................................. B-2
Ersatzteile und Service ........................................................................ B-2
Typenschild ..........................................................................................B-2
Auspacken der Maschine.....................................................................B-2
Wichtige Sicherheitshinweise ..............................................................B-3
Machen Sie sich mit Ihrer Maschine vertraut ............................. B-4 – B-5
Vorbereitung der Maschine zum Einsatz
Installation des Batterie-Satzes ...........................................................B-6
Einrichtung eines neuen Batterie-Satzes .............................................B-6
Installation des Polierkissens ...............................................................B-8
Installation des Staubaufnahmebeutels ...............................................B-8
Inbetriebnahme der Maschine
Vor jedem Einsatz ................................................................................B-8
Planen Sie das Polieren des Bodens...................................................B-8
Inbetriebnahme der Maschine .............................................................B-8
Nach dem Einsatz ................................................................................B-9
Wartung
Wartungsschema .................................................................................B-9
Wartung der Batterien ..........................................................................B-9
Schmierung der Maschine ................................................................... B-9
Kettenspannung - Lenkung und Antrieb ............................................B-10
Fuß- und Feststellbremse ..................................................................B-10
Allgemeine Fehlersuche an der Maschine
Bediener-Anzeigentafel - Überlastungsanzeigen...............................B-11
Bediener-Anzeigentafel - Zustandsanzeigen-Lampen .......................B-11
Wirbelspuren ......................................................................................B-11
Kreise am Boden ...............................................................................B-11
Bodenbeschichtung entfernt .............................................................. B-11
Die Maschine rüttelt bei Betrieb .........................................................B-11
Die Maschine läuft nicht .....................................................................B-11
Technische Daten ..............................................................................B-12
EINLEITUNG
Dieses Handbuch wird Ihnen dabei behilflich sein, das Allerbeste aus Ihrem Nilfisk-Advance Whirlamatic 2700 / BHS 7014 zu machen. Lesen Sie es bitte vor
Inbetriebnahme der Maschine sorgfältig durch.
Bitte beachten Sie: Fettgedruckte Zahlen in Klammern weisen auf ein auf der Seite B-4 – B-5 veranschaulichtes Teil hin.
Dieses Produkt ist lediglich für kommerzielle Anwendungszwecke bestimmt.
ERSATZTEILE UND SERVICE
Eventuelle Reparaturen sollten lediglich von Nilfisk-Advance Fachkräften unter Anwendung von originalen Nilfisk-Advance Zubehör- und Ersatzteilen ausgeführt
werden. Für Ersatzteile bzw. für ein Service wenden Sie sich bitte an Nilfisk-Advance. Bitte geben Sie die Modell- und Seriennummer der betreffenden Maschine
an.
TYPENSCHILD
Die Modell- und Seriennummer Ihrer Maschine sind dem Typenschild an der Maschine zu entnehmen. Diese Angaben sind bei der Bestellung von Ersatzteilen
für die Maschine erforderlich. Tragen Sie bitte nachfolgend die Modell- und Seriennummer Ihrer Maschine ein, um später darauf bezugnehmen zu können.
MODELLNUMMER
SERIENNUMMER
AUSPACKEN DER MASCHINE
Bei Lieferung der Maschine untersuchen Sie bitte den Verpackungskarton und die Maschine sorgfältig auf Schäden. Wenn ein Schaden vorliegt, heben Sie bitte
den Verpackungskarton auf, damit dieser vom Transportunternehmer inspiziert werden kann, der die Lieferung vorgenommen hat. Setzen Sie sich unverzüglich
mit dem Transportunternehmer in Verbindung, um einen Schadensanspruch anzumelden.
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - B-3
DEUTSCH / B-3
WICHTIGE SICHERHEITSHINWEISE
Diese Maschine ist lediglich für kommerzielle Anwendungszwecke geeignet, z. B. in Hotelbetrieben, Schulen, Krankenhäusern,
Fabriken, Geschäften und Büroräumen. Die Maschine ist mit anderen Worten nicht für normale Haushaltszwecke geeignet.
Vor Inbetriebnahme der Maschine sind sämtliche Anweisungen sorgfältig durchzulesen.
WARNHINWEIS!
Zur Verminderung der Feuer- und Verletzungsgefahr sowie der Gefahr durch Stromstöße:
•Die Maschine darf lediglich wie in diesem Handbuch beschrieben betrieben werden. Lediglich die vom Hersteller empfohlenen
Zubehörteile dürfen benutzt werden.
•Diese Maschine darf lediglich von hinreichend ausgebildeten und autorisierten Personen betrieben werden.
• Diese Maschine ist lediglich für den Trockenbetrieb bestimmt und darf außerhalb von Gebäuden unter feuchten Bedingungen
weder betrieben noch abgestellt werden.
• Die Maschine darf nicht als Spielzeug benutzt werden. Besondere Vorsicht ist sowohl beim Betrieb in der Nähe von Kindern
als auch bei der Benutzung durch Kinder geboten.
• Halten Sie Funken, Flammen und rauchende Materialien von den Batterien fern. Während des Normalbetriebes werden
explosive Gase frei.
• Das Laden der Batterien erzeugt hochexplosiven, gasförmigen Wasserstoff. Laden Sie die Batterien lediglich in gut belüfteten
Bereichen, weit entfernt von offenem Feuer. Beim Laden der Batterien ist das Rauchen verboten.
• Entfernen Sie jeglichen Schmuck, wenn Sie in der Nähe von elektrischen Komponenten arbeiten.
• Schalten Sie den Schlüsselschalter aus (O), und unterbrechen Sie die Verbindung zu den Batterien, bevor Sie an den
elektrischen Komponenten Wartungsarbeiten ausführen.
• Arbeiten Sie niemals unter einer Maschine, ohne diese mit Sicherheitsblöcken oder Ständern abzustützen.
• Tragen Sie keine brennbaren Reinigungsmittel auf, nehmen Sie die Maschine nicht auf solchen Mitteln oder in der Nähe
solcher Mittel in Betrieb, und betreiben Sie die Maschine nicht in Bereichen, in denen brennbare Reinigungsmittel gelagert
werden.
• Reinigen Sie die Maschine nicht mit einem Druckreiniger.
• Diese Maschine ist zum Einsatz auf öffentlichen Wegen und Straßen nicht zugelassen.
• Es dürfen keinerlei Gegenstände in Öffnungen eingeführt werden. Während des Betriebes dürfen keine Öffnungen blockiert
sein; entfernen Sie Staub, Fäden, Haare sowie jegliche Fremdkörper, die den Luftstrom beeinträchtigen könnten.
• Setzen Sie diese Maschine nicht auf Rampen und Steigungen von mehr als 5 Grad ein.
• Sorgen Sie beim Einsatz dieser Maschine dafür, daß Drittbeteiligte, insbesondere Kinder, nicht gefährdet sind.
• Bevor Sie irgendwelche Wartungsarbeiten ausführen, lesen Sie alle Anleitungen diese Arbeiten betreffend sorgfältig durch.
• Lassen Sie die Maschine nicht unbeaufsichtigt stehen, ohne vorher den Schlüsselschalter auf “Aus” (O) zu schalten, den
Schlüssel zu entfernen und die Feststellbremse anzuziehen.
• Schalten Sie vor dem Wechseln des Kissens oder dem Öffnen irgendeiner Wartungsluke den Schlüsselschalter auf “Aus” (O).
• Treffen Sie geeignete Maßnahmen um zu verhindern, daß sich Haare, Schmuckgegenstände oder lose Kleidungsstücke in
beweglichen Teilen verfangen.
• Die Maschine darf nicht ohne Staubbeutel und/oder Filter betrieben werden.
• Nicht auf dem Kissengehäuse stehen.
• Diese Maschine ist zur Beseitigung von gesundheitsgefährdendem Staub nicht geeignet.
• Vor dem Verschrotten der Maschine müssen die Batterien entfernt werden. Die Entsorgung der Batterien sollte auf sichere
Weise gemäß der örtlichen Umweltschutzbestimmungen vorgenommen werden.
DIESE ANLEITUNG BITTE AUFBEWAHREN
B-4 - FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014
B-4 / DEUTSCH
1 Kissenmotor-Abdeckung
2 Staubabdeckung
3 Polierkissen
4 Kissenhalter
5 Staubaufnahmebeutel
6 Maschinenverankerung
7 Anschluß des Batterie-Satzes
8 Gaspedal für Vor-/Rücklauf
9 Lenksäulenverstellung
10 Notaus für die Stromversorgung
11 Lenkrad
12 Hupenschalter
13 Hebel zum Anziehen und Lösen der Feststellbremse
14 Fuß-Bremspedal
15 Fahrersitz m/Sicherheitsschalter
16 Ladeanschluß für die Batterie der Maschine
17 Wartungsluke für die Batterien
18 Antriebsräder
19 Steuerräder
20 Automatsicherungen
40 Amp (Antriebsmotor)
5 Amp (Steuerkreis)
21 Abdeckung des Batterie/Steuerungsfaches
22 Stützstange
23 Sitzverstellung
Steuerpult
24 Hauptstromschalter
25 Hauptstromanzeigelampe (grün - O.K. / rot - Störung)
26 Stundenzähler / Störungsanzeige - Kissenantrieb
27 Zustandsanzeigelampe der Drehzahlüberwachung (grün -
Funktion)
28 Überlastungsanzeigelampe - Antriebsmotor
29 Überlastungsanzeigelampe - Hubmotor
30 Überlastungsanzeigelampe - Kissenmotor
31 Batterie-Anzeigelampen
32 Anzeigelampe für gesenktes Kissen (grün - gesenkt & Kissen
“Ein” / gelb - gesenkt & Kissen “Aus”)
33 Schalter zum Heben und Senken des Kissens
34 Anzeigelampe für angehobenes Kissen (grün - angehoben & in
Funktion / rot - angehoben und außer Funktion)
6
9
12
15
19
21
23
1
2
3
4
6
18
20
MACHEN SIE SICH MIT IHRER MASCHINE VERTRAUT
FORM NO. 56041404 - Whirlamatic™ 2700 / BHS 7014 - B-5
DEUTSCH / B-5
5
6
6
7
8
10
11
13
14
16
17
22
27
28
29
30
31
32
33
34
24
25
26
MACHEN SIE SICH MIT IHRER MASCHINE VERTRAUT
STEUERPULT
Loading...