Nilfisk-Advance SC DELTA Instruction Manual

SC DELTA

Instructions for use

107309173 C (09. 2018)

SC DELTA

Operating instructions .................................................................................................... 7

Bedienungsanweisungen ............................................................................................. 15

Instructions de fonctionnement ................................................................................... 23

Instruccciones de funcionamiento .............................................................................. 32

SC DELTA

Min 400 mm Min. 200 mm

Min 500 mm

A.1

A.2

120 mm

Min. 1000 mm

SC DELTA

A.3

A.4

A.3.1

1 1/4" BSP

DKO 28 NUT M36x2 mm

A.5

Inlet

Outlet hose

A.6

SC DELTA

B.1.1

B.1.2

B.1.3

123

B.3

SC DELTA

B.5

C.1 C.2

SC DELTA

Operating Instructions

This high pressure washer has been developed for professional use within:

- agriculture, light industry, transport, building and construction, service

Only use the high pressure washer for purposes described in this manual.

Regarding the following sections:

A - Installation B - Operation C - Maintenance

please refer to pictures in front of the manual.

A - Installation

Before starting

DO READ SAFETY INSTRUCTIONS BEFORE USE!

The SC DELTA is a ﬂ exible pump station capable of supplying several simultaneous users with pressurized cold / hot water through a pipeline. The SC DELTA has been pre-adjusted for a certain line pressure which is also the maximum working pressure.

Operating elements:

1. Water connection with ﬁ lter

1.a Hot (option)

2. Main switch

3. Display

4. Connection of pipe system

5. Electric cable, mounting

6. Adjustable feet (m12)

7. Cabinet

8. E-box

9. Type plate

10. Inspection plug, water tank

11. Filter, water tank

A.1 Temperature conditions

The machine should be installed in a frost-free room. This applies to pump as well as pipelines incl. of outlet points. Con cern ing outdoor outlet points it should be possible to close and emp ty that part of the line which is exposed to frost.

The machine generates heat. Please ensure suﬃ cient ventilation so that the ambient temperature does not exceed 40°C.

1 pump generates around 1 kW heat - 6 pumps 6 kW.

A.2 Condition of distance

In consideration of the cooling system of the machine and the accessibility of service, there must be free wall space on both sides of the machine. To the right 200 mm at a min i mum and to the left 400 mm at a min i mum.

For service there must be at least 1000 mm in front of the machine and 500 mm above the machine.

A.3 Water connection

The water connection is made through a ﬂ exible hose connected to the water inlet(s) (1) of the machine.

The connection can be made to a water supply network or an internal water sup ply. A shut-oﬀ cock should be mounted on the water supply network in the immediate vicini ty of the ma chine. Max. water pressure: 10 bar Min. water pressure: 2 bar Max. water inlet temp.: See label on machine by the water inlet. See A.3.1 for dimensions.

On the back side of the machine there are 2 hoses attached to the water tank. These are overﬂ ow hoses in case of a malfunction in the water tank. The two hoses must not be blocked.

If there is a risk of running sands or other impurities in the inlet water, a sand ﬁ lter (50 micron) should be mounted beyond the internal ﬁ lter of the machine (for further connection data see section Tech ni cal Speciﬁ cations).

Clean the water inlet ﬁ lter once a month or as needed. See C.2.

Note: If option/accessory cold/hot inlet mix is mounted, the temperature out of the machine temperature on the cold inlet (blue point) on the machine.

cannot be lower than the

A.4 Mains power connection

The power system of the SC DELTA is designed in confor- mity with the common European standard:

EN 60204-1:2006+A1:2009: Electrical equipment of machines, Part 1: General requirements.

Power should be connected through a ﬂ exible rubber cable holding copper conductors for 3 phases and earth (PE). The minimum dimensions of the cable are determined by the power consumption of the current system (cf. data sheet), but common to all systems is the following:

Max pre-fuse: 125 A Max core section of cable: 35 mm Min core section of cable: 25 mm

A.4.1 Installation of the main power supply

• Installation of the machine should be carried out by authorized engineer

Equipment to protect the user against electrical shock, should be installed and designed to fulﬁ l the authority requirement for the actual location of the machine, this protection can be done with fuses or Residual Current Device.

Note: High leakage current because of inverter. The power supply cable, minimum 4G25mm², must be con-

nected to the machine through the cable gland in the back of the E-box (1). The wires L1 – L2 – L3 are connected to the main switch –S1, connection points 2 – 4 – 6 on the switch, Earth wire is connected to the main earth terminal placed next to the main switch.

A.4.2 First activation of the main switch with con-

nected main power supply

Before the main switch is turned on, open the E-box and check the below points.

7Original Instructions

Ground fault circuit interrupter

SC DELTA

SUPPLY NETWORK

L2 L3PE

max 125 A

max 35

SC DELTA control system

• Measure the level of the input voltage and compare it to the machine speciﬁ cations.

• Turn on the circuit breakers -F1, -F2 and -F3.

• Turn on the overload protection units for the MPU´s and the frequency inverter -F4 to -F10.

• Close the E-box and turn the two locks to locked position by using the supplied key.

A.5 High pressure connection

IMPORTANT: When connecting to a pipeline always use

the ﬂ exible hose connection from the outlet of the machine. The outlet of the machine can be connected to a pipeline

with ﬁ xed outlet points.

A.6 Venting

Start the machine and open all high pressure cocks on the pipeline until all air has escaped. Start with the re motest high pressure cock.

Please note that the cock should be closed for a short time before opening it again. The latter is done in order to prevent the leakage stop from being activated when venting long pipelines.

Note! The machine may be protected with an antifreeze from the factory. If antifreeze in the machine - catch the ﬁ rst litres until the ﬂ uid is clear water. Collect the water in a container for re-use.

The pump station and outlet points should be placed so that the lines become as short as possible.

• The line should be arranged with as few bends as possible.

• Sometimes it may pay to split the line close to the pump station so the lengths conducting large volumes of water become as short as possible. A centre location of the pump station in relation to the outlet points would also lead to smaller pipe dimensions.

• Pipe lines should be placed on walls of tile or concrete, otherwise great care should be taken (reinforcement plates etc.)

• Pipe lines should be placed so that damage is prevented (collision, frost, extreme attacks of corrosion, etc.)

• Pipe lines should be ﬁ tted in a visual location everywhere or so that they may easily be inspected. Lines should not be incorporated in walls or ﬂ oors. When leading through walls be careful not to enclosed. (Special lead-in bushes are available)

• The outlet points should be placed as close to the operation point as possible and so that a hose length preferably of 20 m is used.

It is recommended to let a service tech ni cian authorized by Nilﬁ sk prepare the pipeline.

B - Operation

B.1 Connections

B.1.1 High pressure hose on pipe system

The Nilﬁ sk high pressure hose with imprinted max. working pressure and temperature should be attached to the outlet connection of the pipe system by the quick coupling (1).

Danger of scalding!

Never dismount high pressure hoses at water temperatures above 50°C.

IMPORTANT: Prior to dismounting of the high pressure hose the machine should be stopped and the shut-oﬀ cock closed. Then activate the trigger of the spray handle to relieve the high pres sure hose of pressure.

B.1.2 Spray handle - accessories

1. Pull forward the quick coupling trigger (1) of the spray handle.

2. Insert the nipple of the spray lance (2) in the quick coupling and release the trigger.

8 Original Instructions

SC DELTA

3. Pull forward the spray lance or any other accessory to ensure correct mounting before starting the machine.

NOTE! Clean nipple of any impurities each time the spray lance has been dismounted.

B.1.3 Application of detergents (external, only 160

bar machines)

If you want to apply detergents or disinfectants these should be dosed to the water through an injector. In conjunction with the injector it may be ad van ta geous to use a wall rack on which spray lances, 2 pcs. of 25 l containers as well as 10 m high pressure hose can be placed.

Below you will ﬁ nd various types of outlet points with injectors.

1. Outlet point with detachable injector

To be attached to the quick coupling of the high pressure cock. To be used for dosing of low-foaming detergents or disin-

fectants. Dosage 1-8%.

2. Outlet point with detachable foam injector

To be attached to the quick coupling of the high pressure cock. To be used in conjunction with foam lance for application of

high-foaming de ter gents or disinfectants. Dosage 1-5%.

3. Outlet point with cleaning trolley and foam injector

To be attached to the quick coupling of the high pressure cock. To be used in the same way as “Outlet point with detachable

foam injector”. Makes it possible to place 4 spray lances, 2 pcs. of 25 l

containers as well as 20 m high pressure hose.

B.2 Start

B.2.1 First activation of the main switch with con-

nected main power supply

By turning the main switch to ON position the control system will start the self-validation procedure and start up the display, please note that there is a start-up delay on the display.

In the self-validation mode, the water tank is ﬁ lled up with water and all the protection circuits are checked. The green circle around the start button will ﬂ ash.

If the water tank is not ﬁ lled up in 4 minutes, the system will stop and the water supply needs to be checked. The water level in the water tank is shown on the display.

machine will stop and turn the green circle oﬀ . When the start button is activated the machine will start up

Motor Pump Unit (MPU) to reach the wanted pressure, it is shown on the display which MPU that is activated, the speciﬁ c MPU-symbol (FIG.1 #8) lights up green. MPU´s will automatically be turned on/oﬀ when output water ﬂ ow is changed, and the frequency inverter will adjust the line pressure to the selected pressure. Actual line pressure is shown on the display (FIG.1 #2).

B.2.3 Line pressure adjustment

The line pressure from the machine can be adjusted. To adjust the pressure, push on the pressure value by the pressure adjustment tab on the display (FIG.1 #13) for 20 sec. then use the +/- tab to adjust to the wanted pressure and press OK to save the value or press cancel to undo the change. NOTE: If the pressure change is permanent, adjustment of the mechanic bypass valve is necessary.

B.2.4 Water tank

The water level will automatically be maintained by the control system, the inlet valve symbol will light up blue on the display when the inlet valve is activated. The actual water temperature is shown on the display (FIG.1 #1).

If the Cold/Hot option is mounted on the machine the water temperature is adjusted to the selected temperature, two valves are shown on the display, one for Cold inlet water and one for Hot inlet water, when the Cold valve is activated it lights up blue and when the hot valve is activated it lights up red. To adjust the temperature, push on the temperature value by the temperature adjustment tab on the display (FIG.1 #12) for 10 sec. and use the +/- tab to adjust to the wanted temperature and press OK to save the value or press cancel to undo the change.

B.2.5 Bypass system

When the output water ﬂ ow is reduced, the bypass system will activate. When the bypass system is activated, the water will return to the water tank, the actually volume is shown on the display (FIG.1 #14), the bar light up and show the water volume, if 1/3 of the bar is blue on a 6 MPU machine, the water from two MPU´s is returning to the water tank.

If more than one pump is active all the redundant pumps will stop after 8 seconds, if the outlet is completely closed the last pump will stop after 20 sec.

The machine is still active and starts up again when the line pressure drops below the start pressure.

B.2.6 Errors and warnings.

When the water tank is ﬁ lled with water and the system is ready to start, the green circle will stop ﬂ ashing.

B.2.2 Start/stop

Press the start button on the display (FIG.1 #3) and the green circle around the button will light up.

Press the stop button on the display (FIG.1 #4) and the

There are two types of failures in the control system on the machine:

• Error: Inverter error, Critical water level, All MPU deactivated, Inlet water ﬂ ow low, low output pressure, High temperature water tank, remote or display communication failure. These errors will stop the machine immediately because it is critical for the machine or connected systems.

• Warnings: MPU oil level low, MPU thermic high temp, MPU overload protection activated, abnormal water level

9Original Instructions

SC DELTA

in water tank, Slave #1 or #2 communication failure. These warnings won´t stop the machine.

The actual warning will be shown on the Display, to reset press the aﬀ ected MPU or the water tank where the warning

B.2.7 Display

is active and the system will validate that the warnings is gone and set the system to normal status again.

The reset is done without stopping the machine totally.

FIG. 1

Symbol Ref # Function Signal Action

MPU

- Actual water temp.

- Reset water temp. error

- Actual line pressure

- Reset output pressure low limit (option)

- Start machine Flash green - control system in

- Stop machine

- Reset warning / error

Red - water temperature error - Check inlet water tempera-

Red - output pressure low limit error (option)

self-validation mode. Green - machine active

Flash red - system warning

Red - system error

Red - actual MPU# temperature warning

- Check water ﬂ ow

- Check available pumps

Check below points:

- MPU oil level

- MPU internal heat sensor

- MPU overload protection

- WBT below normal level

- Inverter failure

- Water level error

- Check air intake MPU

ture - if OK, contact Service

MPU

10 Original Instructions

Red - oil level low actual MPU# - Check oil level

SC DELTA

Symbol Ref # Function Signal Action

MPU

- Reset warning on actual MPU

Red - overload protection activated for actual MPU#

Flash red - MPU deactivated on the overload protection unit

Green - MPU activated

- Check power supply

- Before reset please make

sure that the problem is solved

Water tank

Temp.

Pressure

Backﬂ ow

bar

- Hour counter actual MPU

- Service functions Flash blue - 20 hours or less to

- Reset low water level warning Water tank square symbol:

- Adjust water tank temperature

- Press the value (60°C) for 10 sec. to open the adjustment window (option/accessory)

- Adjust the line pressure.

- Press the value (100) for 20 sec. to open the adjustment window

Highlighted square when reset is possible

Flash red - warning on inverter MPU (oil, temp., overload)

Red - inverter failure

next service Blue - service needed

Blue - normal water level Yellow - warning water level Red - Critical water level

Water inlet Valves: Blue - Cold water inlet open Red - Hot water inlet open

Blue - the bar will be coloured to show the amount of water that ﬂ ows back to the water brake tank. If 1/3 of the bar is blue on a 6 MPU machine, it means that 2 MPUs are bypassing water.

Red - failure on the 1. Slave machine. Only with master/ slave machines

Red - failure on the 2. Slave machine. Only with master/ slave machines

- Check MPU where the failure is down

- Contact service

- Check water supply

- Check water ﬁ lter

- Check water supply

- Check water ﬁ lter

- Check the UI Display on the

1. Slave machine to see the actual failure

- Check the UI Display on the

2. Slave machine to see the actual failure

11Original Instructions

SC DELTA

B.3 Operation - automatic start/stop

Always hold the spray lance with both hands!

The machine is automatically activated when the trigger (1) of the spray handle is activated.

When the trigger is released, the machine automatically stops after 20 seconds.

When the machine is not in use, the trigger should be locked with locking device (2).

B.4 Stop

Danger of scalding!

Never detach high pressure hoses at a water temperature above 50°C.

Never detach the high pressure hose while the machine is in operation.

1. To stop the machine, push the red stop button (#4) and turn the main switch (2) to position - 0 -.

B.5 Frost protection

The machine should be installed in a frost-free room. This applies to pump as well as pipelines incl. of outlet points. Concerning outdoor outlet points it should be possible to empty that part of the line which is exposed to frost.

IMPORTANT: For safety reasons, hoses, spray lances and other accessories should always be thawed prior to use.

C - Maintenance

It applies to the most exposed components that a minimum of maintenance ensures a prolonged and prob lem-free operation. Therefore it will be a good idea to make a habit of the following:

Maintenance Schedule

Every six months

or 500 operating

hours

As required

Checking pump oil level

Weekly



After the ﬁ rst 50 operating hours

Changing pump oil

Cleaning water ﬁ lter

Prior to attaching the water hose and the high pressure hose, the quick couplings should be cleaned of dust and sand.

Prior to attaching the spray lance or other accessories to the spray handle, the machine should be started and the quick coupling cleaned of dust and sand.



C.1 Oil

Check the oil level in the oil glas. If the oil level gets too low, the pump will automatically

shut down and #6 will light up. In the case of repeated low oil level (oil waste) please

contact a Nilﬁ sk service technician.

PROTECT THE ENVIRONMENT

Waste oil and oil sludge must be removed as laid down in the instructions.

C.2 Water ﬁ lter

To avoid debris entering the high pressure pump, a water ﬁ lter (ﬁ ne) is ﬁ tted at the wa ter inlet. Dependent on the purity of the water, this ﬁ l ter will have to be cleaned at regular in ter vals.



C.3 Cleaning of high pressure nozzle

A clogging up in the nozzle causes bad cleaning, and a cleaning of the nozzle is immediately required.

1. Stop the machine and detach the spray lance.

2. Clean the nozzle.

IMPORTANT: ONLY use the cleaning tool when the spray

lance is detached.

3. Flush the spray lance backwards with water.

4. If the pressure is still too high, repeat items 1-3.

C.4 Disposable waste

This high pressure washer consists of parts which can aﬀ ect the environment when thrown away. Parts that can pollute are as follows:

Oil, painted/zinc-coated parts, plastics/plastic-coated parts. Therefore, it is important to follow the laws concerning the

removal of polluting and dangerous materials when replacing spare parts or disposing of high pressure washer.

It is recommended that you bring the rejected parts to waste disposal areas or recycling plants that are approved for the destruction of these types of materials.

The ﬁ lter can be removed when the plug (pos. 1) has been un screwed.

There is also a ﬁ lter in the tank (pos. 11). This ﬁ lter can be removed by dismounting the two screws (torx 20).

Pull the ﬁ lter up and out of the water tank. Clean the ﬁ lter and remount it.

12 Original Instructions

SC DELTA

Troubleshooting

You have chosen the best quality and therefore deserve the best service. To avoid unnecessary dis ap point ments, you should check the following before contacting the nearest Nilﬁ sk service organisation:

Symptom Reason Action Machine/pump will not start > A fuse has blown

> Power/plug not connected > Thermal switches in motor activated

(red lamp ﬂ ashes) #5

> Thermal relay switched oﬀ (red lamp

ﬂ ashes) #5

> Oil shortage in pump

Fuses blow > Installation does not correspond to the

ampere consumption of the machine

Working pressure too low > Nozzle worn

> Wrong spray lance > Too many users on the system > Reduction valve of spray lance not

adjusted to max. pressure.

> Nozzle partly clogged up

Working pressure not steady > Water temperature too high

> Insuﬃ cient water supply to pumps

> Air in the system > Water ﬁ lters clogged up

No working pressure > Nozzle clogged up

> No inlet water

> High pressure cock of outlet point open.

Machine/pumps start and stop > Leaky hose/ pipeline/spray handle • Repair leak.

Pump stops > Oil shortage in pump. Lamp ﬂ ashes #6 • Top up with oil.

• Change the fuse.

• Connect power/plug.

• Let the motor cool. Start the machine and check that the working pressure is not too high and that the mains voltage corresponds to the speciﬁ cations.

• Reﬁ ll with oil.

• Change to an installation corresponding to the ampere consumption of the machine at a minimum. Replace the fuse.

• Replace the nozzle.

• Replace the spray lance.

•

Turn reduction valve completely counter-

clockwise.

• Clean the nozzle (see section C.3).

• Lower the temperature of the inlet water to max. temperature (see Technical Speciﬁ cations).

• Check water inlet ﬁ lter + ﬁ lter in water tank. If that does not solve the problem, the water supply for the machine is insuﬃ cient.

• Vent the system (see section A.7).

• Clean ﬁ lters (see sect. C.2)

• Clean nozzle (see sect. D.3)

• Check that the shut oﬀ cock of the water inlet is open. Check that the water supply meets the requirements (see section A.4)

• Close all high pressure cocks not in use.

Should other malfunctions occur than those mentioned above, please contact your nearest Nilﬁ sk service organisation. Machine failure - see B2.6 and B2.7.

13Original Instructions

SC DELTA

Warranty

Your Nilﬁ sk product is guaranteed for 12 months from date of purchase (purchase receipt must be presented) on the following conditions:

• that defects are attributable to ﬂ aws or defects in materials or workmanship. (Usual wear and tear as well as misuse are not covered by the guarantee).

• that repairs have not been carried out or attempted by other than Nilﬁ sk-trained service staﬀ .

• that only original accessories have been applied.

• that the product has not been exposed to abuse such as knocks, bumps or frost.

• that the instructions in the manual have been carefully observed.

A warranty repair comprises the replacement of defective parts, but it does not cover freight and packaging charges. Besides we refer to national Sale of Goods Act.

Any illegitimate guarantee repair will be invoiced. (I.e. malfunctions due to causes mentioned in section “Troubleshooting” of the instruction manual).

14 Original Instructions

Specifications

SC DELTA

160/4500-3

SC DELTA

160/6000-4

SC DELTA

160/6000-4

SC DELTA

160/9000-6

SC DELTA

160/9000-6

SC DELTA

100/7500-3

SC DELTA

100/10000-4

SC DELTA

100/15000-6

IEC

max

V/ph/Hz 400V/3ph/50Hz

A 4864589587486495

kW 27 35 55 27 35 55

bar (MPa)

l/h

IEC

bar (MPa)

max

l/h 4500 6000 9000 7500 10000 15000

°C (°F) 70 (158)

bar (MPa)

max

bar (MPa)

min

EU EU EXPT EU EXPT EU EU EU

440V/3ph/

60Hz

400V/3ph/

50Hz

440V/3ph/

60Hz

400V/3ph/50Hz

160 (16) 100 (10)

4400 5800 8600 7000 9500 14500

250 (25) 150 (15)

10 (1)

2 (0.2)

(IEC 60335-2-69)

(ISO 5349 ah)

mm 970x1050x1800

kg 349 408 526 348 408 526

dB(A)+/-2 84 85 87 84 85 87

dB(A)+/-2 100 101 103 100 101 103

m/s

<1.5+/-1

N 27-122

0.81 (x3)

0.81 (x4) 0.81 (x6)

0.81 (x3)

0.81 (x4)

0.81 (x6)

Castrol Alphasyn T150

Min. 0350 0700

EN: Country variant. DE: Ländervarianten. FR: Selon le pays. ES: Depende del

país.

EN: Possible voltage. DE: Mögliche Spannung. FR: Tension autorisée. ES: Ten-

V/ph/Hz

sión admitida.

Pmax

8 Q

IEC

bar

(MPa)

l/h

bar

(MPa)

max

l/h

EN: Fuse. DE: Sicherung. FR: Fusible. ES: Fusible. EN: Power rating. DE: Nennleistung. FR: Puissance nominale. ES: Potencia nomi-

nal. EN: Working pressure. DE: Arbeitsdruk. FR: Pression de service. ES: Presión de

trabajo.

EN: Water flow. DE: Wasserdurchsatz. FR: Débit d‘eau. ES: Flujo de agua. EN: Max. water pressure. DE: Max Wasserdruck. FR: Pression d‘eau maximale.

ES: Presión máxima de entrada del agua.

EN: Water flow DE: Wasserdurchsatz. FR: Débit d‘eau. ES: Flujo de agua. EN: Max water inlet temperature, Intake-Pressure operation. DE: Max Wasserein-

max

°C (°F)

bar

max

(MPa)

bar

min

(MPa)

lasstemperatur - Druckbetrieb. FR: Température max. de l‘entrée d‘eau en mode admission/pression. ES: Temperatura y presión máxima de entrada del agua. EN: Max. water inlet pressure. DE: Max. Wassereinlassdruck. FR: d‘eau en mode admission/pression. ES: Presión máxima de entrada del agua.

EN: Min. water inlet pressure. DE: Min. Wassereinlassdruck. FR: d‘eau en mode admission/pression Min. ES: Presión mínima de entrada del agua.

EN: Max dry suction height. DE: Max. Trockensaughöhe. FR: Hauteur d‘aspiration à sec max. ES: Altura máxima de succión en seco.

EN: Dimensions LxWxH. DE: Masse LxBxH. FR: Dimensions l x p x h. ES: Dimen-

siones l x a x al.

(IEC 60335-2-69)

(ISO 5349 ah)

dB(A)

+/-2

dB(A)

+/-2

m/s2

EN: Weight. DE: Gewicht. FR: Poids du nettoyeur. ES: Peso del limpiador.

EN: Sound pressure level LPA. DE: Schalldruckpegel. FR: Niveau de pression acoustique. ES: Nivel de presión sonora.

EN: Sound power level LWA. DE: Schallleistungspegel. FR: Niveau de puissance acoustique. ES: Potencia acústica.

EN: Vibration. DE: Vibrationen FR: Vibration ES: Vibración

EN: Recoil forces, lance. DE: Rückstoßkraft, Sprührohr. FR: Forces de recul, lan- ce. ES: Fuerzas de retroceso, lanza. EN: Oil quantity. DE: Ölmenge. FR: Quantité d‘huile. ES: Cantidad de aceite.

EN: Oil type. DE: Öltyp. FR: Type d‘huile. ES: Tipo de aceite.

EN: Nozzle size. DE: Düsengrösse. FR: Taille de la buse. ES: Tamaño de la boquilla

EN: Specifications and details are subject to change without prior notice. DE: Technische Daten und Details des Ge-

räts können sich ohne vorherige Ankündigung ändern. FR: Ces spécifications et détails sont susceptibles d’être modifiés sans préavis. ES: Las especificaciones y los datos están sujetos a cambios sin previo aviso.

HEAD QUARTER

DENMARK

Nilﬁ sk A/S Kornmarksvej 1 DK-2605 Broendby Tel.: (+45) 4323 8100

www.nilﬁ sk.com

SALES COMPANIES

ARGENTINA

Nilﬁ sk Argentina Herrera 1855 Piso 4° B Oﬁ c 405 Ciudad de Buenos Aires Tel.: (+54) 11 6091 1576

www.nilﬁ sk.com.ar

AUSTRALIA

Nilﬁ sk Pty Ltd Unit 1/13 Bessemer Street Blacktown NSW 2148 Tel.: (+61) 2 98348100 www.nilﬁ sk.com.au

AUSTRIA

Nilﬁ sk GmbH Metzgerstrasse 68 5101 Bergheim bei Salzburg Tel.: (+43) 662 456 400 90 www.nilﬁ sk.at

BELGIUM

Nilﬁ sk n.v-s.a. Riverside Business Park Boulevard Internationalelaan 55 Bâtiment C3/C4 Gebouw Bruxelles 1070 Tel.: (+32) 24 67 60 50 www.nilﬁ sk.be

BRAZIL

Nilﬁ sk do Brasil Av. Eng. Luis Carlos Berrini, 550 40 Andar, Sala 03 SP - 04571-000 Sao Paulo Tel.: (+11) 3959-0300 / 3945-4744 www.nilﬁ sk.com.br

CANADA

Nilﬁ sk Canada Company 240 Superior Boulevard Mississauga, Ontario L5T 2L2 Tel.: (+1) 800-668-8400 www.nilﬁ sk.ca

CHILE

Nilﬁ sk S.A. (Comercial KCS Ltda) Salar de Llamara 822 8320000 Santiago Tel.: (+56) 2684 5000 www.nilﬁ sk.cl

CHINA

Nilﬁ sk 4189 Yindu Road Xinzhuang Industrial Park 201108 Shanghai Tel.: (+86) 21 3323 2000 www.nilﬁ sk.cn

CZECH REPUBLIC

Nilﬁ sk s.r.o. VGP Park Horní Počernice Do Čertous 1/2658 193 00 Praha 9 Tel.: (+420) 244 090 912 www.nilﬁ sk.cz

DENMARK

Nilﬁ sk Danmark A/S Industrivej 1 Hadsund, DK-9560 Tel.: 72 18 21 20 www.nilﬁ sk.dk

FINLAND

Nilﬁ sk Oy Ab Koskelontie 23 E 02920 Espoo Tel.: (+358) 207 890 600 www.nilﬁ sk.ﬁ

FRANCE

Nilﬁ sk SAS 26 Avenue de la Baltique Villebon sur Yvette 91978 Courtabouef Cedex Tel.: (+33) 169 59 87 00 www.nilﬁ sk.fr

GERMANY

Nilﬁ sk GmbH Guido-Oberdorfer-Straße 2-10 89287 Bellenberg Tel.: (+49) (0)7306/72-444 www.nilﬁ sk.de

GREECE

Nilﬁ sk A.E. Αναπαύσεως 29

Κορωπί Τ.Κ. 194 00

Tel.: (30) 210 9119 600 www.nilﬁ sk.gr

HOLLAND

Nilﬁ sk B.V. Versterkerstraat 5 1322 AN Almere Tel.: (+31) 036 5460760 www.nilﬁ sk.nl

HONG KONG

Nilﬁ sk Ltd. 2001 HK Worsted Mills Industrial Building 31-39, Wo Tong Tsui St. Kwai Chung, N.T. Tel.: (+852) 2427 5951 www.nilﬁ sk.com

HUNGARY

Nilﬁ sk Kft. II. Rákóczi Ferenc út 10 2310 Szigetszentmiklós-Lakihegy Tel.: (+36) 24 475 550 www.nilﬁ sk.hu

INDIA

Nilﬁ sk India Limited Pramukh Plaza, ‘B’ Wing, 4th ﬂ oor, Unit No. 403 Cardinal Gracious Road, Chakala Andheri (East) Mumbai 400 099 Tel.: (+91) 22 6118 8188 www.nilﬁ sk.in

IRELAND

Nilﬁ sk 1 Stokes Place St. Stephen’s Green Dublin 2 Tel.: (+35) 3 12 94 38 38 www.nilﬁ sk.ie

ITALY

Nilﬁ sk SpA Strada Comunale della Braglia, 18 26862 Guardamiglio (LO) Tel.: (+39) (0) 377 414021 www.nilﬁ sk.it

JAPAN

Nilﬁ sk Inc. 1-6-6 Kita-shinyokohama, Kouhoku-ku Yokohama, 223-0059 Tel.: (+81) 45548 2571 www.nilﬁ sk.com

MALAYSIA

Nilﬁ sk Sdn Bhd Sd 33, Jalan KIP 10 Taman Perindustrian KIP Sri Damansara 52200 Kuala Lumpur Tel.: (60) 3603 627 43 120 www.nilﬁ sk.com

MEXICO

Nilﬁ sk de Mexico, S. de R.L. de C.V. Pirineos #515 Int. 60-70 Microparque Industrial WSantiago 76120 Queretaro Tel.: (+52) (442) 427 77 00 www.nilﬁ sk.com

NEW ZEALAND

Nilﬁ sk Limited Suite F, Building E 42 Tawa Drive 0632 Albany Auckland Tel.: (+64) 9 414 1996 Website: www.nilﬁ sk.com

NORWAY

Nilﬁ sk AS Bjørnerudveien 24 1266 Oslo Tel.: (+47) 22 75 17 80 www.nilﬁ sk.no

PERU

Nilﬁ sk S.A.C. Calle Boulevard 162, Of. 703, Lima 33Perú Lima Tel.: (511) 435-6840 www.nilﬁ sk.com

POLAND

Nilﬁ sk Sp. Z.O.O. Millenium Logistic Park ul. 3 Maja 8, Bud. B4 05-800 Pruszków Tel.: (+48) 22 738 3750 www.nilﬁ sk.pl

PORTUGAL

Nilﬁ sk Lda. Sintra Business Park Zona Industrial Da Abrunheira Ediﬁ cio 1, 1° A P2710-089 Sintra

Tel.: (+351) 21 911 2670 www.nilﬁ sk.pt

RUSSIA

Nilﬁ sk LLC Vyatskaya str. 27, bld. 7/1st 127015 Moscow Tel.: (+7) 495 783 9602 www.nilﬁ sk.ru

SINGAPORE

Den-Sin 22 Tuas Avenue 2 639453 Singapore Tel.: (+65) 6268 1006 www.densin.com

SLOVAKIA

Nilﬁ sk s.r.o. Bancíkovej 1/A SK-821 03 Bratislava Tel.: (+421) 910 222 928 www.nilﬁ sk.sk

SOUTH AFRICA

Nilﬁ sk (Pty) Ltd Kimbult Oﬃ ce Park 9 Zeiss Road Laser Park Honeydew Johannesburg Tel: +27118014600 www.nilﬁ sk.co.za

SOUTH KOREA

Nilﬁ sk Korea #204 2F Seoulsup Kolon Digital Tower 25 Seongsuil-ro 4-gil, Seongdong-gu Seoul. Tel.: (+ 82) 2 3474 4141 www.nilﬁ sk.co.kr

SPAIN

Nilﬁ sk S.A. Torre d’Ara, Passeig del Rengle, 5 Plta. 10 08302 Mataró Tel.: (34) 93 741 2400 www.nilﬁ sk.es

SWEDEN

Nilﬁ sk AB Taljegårdsgatan 4 431 53 Mölndal Tel.: (+46) 31 706 73 00 www.nilﬁ sk.se

SWITZERLAND

Nilﬁ sk AG Ringstrasse 19 Kircheberg/Industri Stelz 9500 Wil Tel.: (+41) 71 92 38 444 www.nilﬁ sk.ch

TAIWAN

Nilﬁ sk Ltd Taiwan Branch (H.K) No. 5, Wan Fang Road Taipei Tel.: (+88) 6227 00 22 68 www.nilﬁ sk.tw

THAILAND

Nilﬁ sk Co. Ltd. 89 Soi Chokechai-Ruammitr Viphavadee-Rangsit Road Ladyao, Jatuchak, Bangkok 10900 Tel.: (+66) 2275 5630 www.nilﬁ sk.co.th

TURKEY

Nilﬁ sk A.S. Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7 Ümraniye, 34775 Istanbul Tel.: +90 216 466 94 94 www.nilﬁ sk.com.tr

UNITED ARAB EMIRATES

Nilﬁ sk Middle East Branch SAIF-Zone P.O. Box 122298 Sharjah Tel.: (+971) (0) 655-78813 www.nilﬁ sk.com

UNITED KINGDOM

Nilﬁ sk Ltd. Nilﬁ sk House, Bowerbank Way Gilwilly Industrial Estate, Penrith Cumbria CA11 9BQ Tel: (+44) (0) 1768 868995 www.nilﬁ sk.co.uk

UNITED STATES

Nilﬁ sk, Inc. 9435 Winnetka Ave N, Brooklyn Park MN- 55445 www.nilﬁ sk.com

VIETNAM

Nilﬁ sk Vietnam No. 51 Doc Ngu Str. P. Vinh Phúc, Q.Ba Dinh Hanoi Tel.: (+84) 761 5642 www.nilﬁ sk.com

Nilfisk-Advance SC DELTA Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual