Nilfisk-Advance POSEIDON 2, Poseidon 2-20, Poseidon 2-22 T, Poseidon 2-22 XT, Poseidon 2-25 XT Operating Instructions Manual

Operating
instructions

POSEIDON 2

128330683 c (05.2014)
DA-NO-SV-FI-EN-DE-FR-NL-IT-ES-PT-EL

Copyright © 2014 Nilfisk-ALTO, Division of Nilfisk-Advance A/S

Instruktionsbog ............................................... 3 - 16

Instruksjonsbok ............................................... 17 - 31

Instruktionsbok ............................................... 32 - 46

Käyttöohje ...................................................... 47 - 61

Instruction manual ......................................... 62 - 75

Betriebsanleitung ........................................... 76 - 92

Manuel d'Instructions ..................................... 93 - 108

Gebruikershandleiding ................................... 109 - 123

Manuale di istruzioni ..................................... 124 - 138

Manual de Instrucciones ................................ 139 - 154

Manual de Instruções ..................................... 155 - 169

γχειριδιο οδηγιων ............................................. 170 - 186

62 Original Instructions

Poseidon 2

Index

1 Safety precautions and warnings ...........................................62

2 Description .............................................................................64

3 Before you start using your pressure washer .........................65

4 Operating your pressure washer ............................................66

5 Fields of application and working methods ............................70

6 After using your pressure washer ...........................................71

7 Maintenance ...........................................................................72

8 Trouble Shooting ....................................................................73

9 Further information .................................................................74

10 Main Technical Data ...............................................................74

11 EC Declaration of Conformity .................................................75

1 Safety Precautions and Warnings

Before starting up
your high-pres­sure washer for
the fi rst time, this

instruction manual
must be read through carefully.
Save the instructions for later
use.

Safety instructions
marked with this
symbol must be
observed to pre-

vent danger to persons.

This symbol is

used to mark

safety instruc-

tions that must

be observed to

prevent damage to the

machine and its performance.

This symbol
indicates tips

and instructions
to simplify work and to ensure a
safe operation.



WARNING!

Inhalation of aerosols can be
hazardous to health. Where
applicable use a device in order
to avoid or reduce aerosols
production, e.g., a shield cover­ing the nozzle. For protection
against aerosols use a res­piratory mask of class FFP 2 or
higher.

Do not let children or people
who have not read the instruc­tion manual ope rate the ma­chine.

This appliance is not intended
for use by children or other
persons without assistance or

supervision if their physical,
sensory or mental capabili­ties prevent them from using it
safely. Children should be su­pervised to ensure that they do
not play with the appliance.

Before starting up your ma­chine please check it carefully
for any defects. If you fi nd any,
do not start up your machine
and contact your Nilfi sk-ALTO
distributor.

Especially check:

 The insulation of the electric

cable should be faultless
and without any cracks. If the
electric cable is damaged,

an authorized Nilfi sk-ALTO
distributor should replace it.

WARNING!

 High pressure jets can be

dangerous. Never direct the
water jet at persons, animals,
live electrical equipment or
the machine itself.

 Never try to clean clothes or

footwear on yourself or other
persons.

 Hold the spray lance fi rmly

with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope­ration.

 The operator and anyone in

the immediate vicinity of the

Symbols used to mark in­structions

63

Poseidon 2

Original Instructions

site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles during opera­tion.

 This appliance has been de-

signed for use with cleaning
agents supplied or recom­mended by the manufacturer.
The use of other cleaning

agents or chemicals may

adversely affect the safety of

the appliance.

 To ensure the appliance

safety only use original spare
parts from the manufacturer
or approved by the manufac­turer.

 High pressure hoses, fi ttings

and couplings are important
for the safety of the appli­ance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.

 Do not use the appliance

if a supply cord or impor­tant parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trig­ger gun.

 Remove the plug from the

socket outlet during cleaning
or maintenance.

 Appropriate ear protection

must be used.

 Never use the machine in

an environment where there
could be a danger of explo­sion. If any doubt arises,
please contact the local
authorities.

 It is not allowed to clean

asbestos- containing surfaces
with high pressure.

 Do not spray fl ammable

liquids.

 Always switch off the mains

disconnecting switch when
leaving the machine unat­tended.

This high pressure washer

must not be used at tempera­tures below 0°C.

WARNING!

Inadequate extension cables
can be dangerous. If an exten­sion cord is used, it shall be
suitable for outdoor use, and

the connection has to be kept
dry and off the ground. It is
recommended that this is ac­complished by means of a ca­ble reel which keeps the socket
at least 60 mm above the
ground. Cables on reels should
always be completely unwound
to prevent the cable from over­heating.

Extension cables should com­ply with the below-mentioned
requirements for length and
cable dimensions.

1.0 mm² max. 12.5 m

1.5 mm² max. 20 m

2.5 mm² max. 30 m

Only 100-120 V machines:

2.0 mm² máx. 12.5 m

2.5 mm² máx. 20 m

 If the electric cable is

damaged, it must be re­placed by the manufacturer
or his service agent or simi­larly qualifi ed person in order
to avoid a hazard.

Mains power connection

The following should be ob­served when connecting the
high pressure washer to the
electric installation:
 Only connect the machine to

an installation with earth con­nection.

 The electric installation shall

be made by a certifi ed elec­trician and comply with IEC
60364-1.

 It is strongly recommended

that the electric supply to this
machine should include a re­sidual current device (GFCI).

Water connection

Connection to the public mains
according to regulations.

Machine not suit-

able for connec­tion to the potable
water mains.

This high pressure washer is
only allowed to be connected
with the drinking water mains,
when an appropriate backfl ow
preventer has been installed,
Type BA according to EN 1717.
The length of the hose between
the backfl ow preventer and the
high pressure washer must be
at least 10 metres to absorb
possible pressure peaks (min
diameter ½ inch).
Operation by suction (for
example from a rainwater ves­sel) is carried out without back­fl ow preventer.
As soon as water has fl own
through the BA valve, this water
is not considered to be drinking
water any more.

IMPORTANT! Only use wa­ter without any impurities. If

there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi­tional fi lter should be mounted
(max. 50 micron).

Safety devices

Locking device on spray handle
(7a) (see illustration at the end

of this manual):
The spray handle features a
locking device. When the button
is activated, the spray handle
cannot be ope rated.

Thermal sensor:

A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen­sor has cooled.

Pressure safety device

An integrated hydraulic safety
valve protects the system from
excessive pressure.

64 Original Instructions

Poseidon 2

2 Description

This high-pressure washer has
been developed for semiprofes­sional routine cleaning:

- Professional craftsman jobs,
cleaning of vehicles, boat,
caravan and minor cleaning
jobs within building and con­struction

Section 5 describes the use of

the high-pressure washer for
various cleaning jobs.

Only use the high-pressure
washer for purposes described
in this manual.

The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.

2.1 Application

2.2 Operation elements
and model survey

See illustration at the end of
this manual.

1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection

(only machines without

hose reel)
4 High pressure hose
5 Electric cable
6 Button for regulation of

pressure and water volume
7 Ergo 2000 spray handle

with lock (7a)
8 Flexopower Plus spray

lance
9 Turbohammer Plus spray

lance

10 Detachable detergent con-

tainer
11 Nozzle cleaning tool
12 Dosing of detergents
13 Hose reel
14 Hose hook (only machines

without hose reel)
15 Model tag
16 Button for telescopic handle
17 Telescopic handle
18 Turnable cable hook

Specifi cations: See model tag
(15) of machine.

We reserve the right to alter the
specifi cations.

65

Poseidon 2

Original Instructions

3 Before you start using your
pressure washer

3.1 Mounting of holders for
spray lance

Mount the holders for spray
lance on the machine.

3.2 Mounting of hose hook

(only models without

hose reel)

Mount the hose hook (14) on
the handle (2 screws).

Note: the hose hook can be
mounted on the front as well as
on the back. Front position is to
be used if the product is used
together with a special wall
hook for wall storage.

3.3 Mounting of hose reel
handle (only models with
hose reel)

1. Click the hose reel handle
on to the trolley handle (no
screws).

66 Original Instructions

Poseidon 2

3.4 Mounting of quick
coupling

1. Screw the quick coupling
tight on to the water inlet (2).

Note: The inlet fi lter must al­ways be fi tted in the water inlet
pipe to fi lter out major impuri­ties as these will damage the
pump valves.

Caution: Failure

to fi t the fi lter will

invalidate the

guarantee.



3.5 Mounting of high
pressure hose

Attach the high pressure hose
(4) to the spray handle (7).

4 Operating your pressure washer

4.1 Connection of high pres­sure hose

Machines without hose reel: At­tach the high pressure hose (4)
to the high pressure connection
of the machine (3).

Only max. 7 m additional exten­sion hose can be added.

Machines with hose reel: Un­wind the high pressure hose
completely.

67

Poseidon 2

Original Instructions

4.2 Mounting of spray

lance

1. Pull the blue quick-release
grip (A) of the spray gun
backwards.

2. Insert the nipple of the spray
lance (B) into the quick-re­lease connection and release
it.

3. Pull the spray lance (or other
accessory) forwards to check
that it is securely attached to
the spray gun.

4.3 Water connection An ordinary 1/2" garden hose of
min. 10 m and max. 25 m will

be suitable.

NOTE: Connec­tion to the public
mains according
to regulations.

IMPORTANT! Only use wa­ter without any impurities. If

there is a risk of silt, sand or
sediment in the inlet water (i.e.
from your own well), an addi­tional fi lter should be mounted.

1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrat­ing the machine.

Note: Check
that the fi lter is

fi tted in the water
inlet pipe and that it is clean
and free from debris.

2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 60°C).

3. Turn on the water.

4.4 Telescopic handle

The machine features a tele­scopic handle. To raise or lower
the handle, press the button
(16) and move the handle up­wards or downwards. When a
click is heard, the handle is in
right position.

NOTE!

Always remove any dirt from
the nipple before connecting
the spray lance to the spray
handle.

A

B

68 Original Instructions

Poseidon 2

hose in a tank or bucket. To
avoid water spillage, crimp
the water inlet hose down in
the water and then connect
the hose to the machine with
the quick coupling and fi nally
uncrimp the water inlet hose.

2. Dismount spray handle,
lance and nozzle.

3. Turn the start/stop switch to
position "I" and let the water
run, until the air has escaped
from the water hose and the
pump.

4. Mount spray handle and
thereafter lance.

4.6 Start the machine (when
connected to open con­tainers (suction mode))

4.5 Start and stop of the ma­chine (when connected
to a water supply)

The spray lance is affected
by a thrust during opera­tion - therefore always hold it
fi rmly with both hands. IMPOR-

TANT: Point the nozzle at the
ground.

1. Check that the machine is in
upright position.

NOTE: Do not place the ma-

chine in tall grass!

2. Release the trigger lock.

3. Activate the trigger of the
spray handle and let the wa­ter run until all air has es­caped from the high pressure
hose.

4. Turn the start/stop switch (1)
to position "I".

5. Activate the trigger of the
spray handle.

Always adjust the distance and
thus the pressure of the nozzle

to the surface, which is to be
cleaned.

Do not cover the
machine during
operation.

Note: If the machine is left or
not used for 5 minutes, it must
be switched off on the start/stop
switch "O" (1):

1. Turn the start/stop switch to
position "O".

2. Disconnect the electrical plug
from the socket.

3. Shut off the water supply and
activate the trigger to relieve
the machine of pressure.

4. Lock the spray handle.

When releasing the trigger of
the spray handle, the machine
automatically stops. The ma­chine will start again when you
re-activate the spray handle.

The washer can take in water
from a rain water tank as an
example. The hose for the water
supply must not be too long,
approx. 5 m.

Make sure that the water tank is
not placed on a lower level than
the machine.

Use an external fi lter if the wa­ter contains impurities.

1. Make sure that the water
hose is fi lled completely with
water before connecting to
the machine. Place the entire

High pressure

Low pressure

4.7 Pressure regulation on
the Flexopower Plus-

spray lance

The pressure can be regulated
on the Flexopower Plus spray
lance.

69

Poseidon 2

Original Instructions

4.8 Operation with detergents Application of detergents is

NOT possible if an extension

hose is applied.

1. Fill the container with a de­tergent.

2. Mount the Flexopower Plus
spray lance and adjust it to
low pressure (see section

4.7).

3. Adjust the dosing regulator
(12) to the re quired vol ume

of detergent (0-5%).

4. Apply the detergent from
below and up wards.

5. Let the detergent act for the
time stated on the packing of
the detergent and fl ush with
pure water.

External detergent container

1. Remove the cover with suc­tion hose from the detergent
container.

2. Mount the cover with suction
hose on the external deter­gent container.

The cover has a standard thread
and fi ts common detergent con­tainers. If your container does
not have a standard thread,
detach the fi lter from the suc­tion hose and remove the cover.
Remount the fi lter in the suction
hose.

Extra detergent hose can be
pulled out of the machine.

4.9 Regulation of pressure /
water volume

Working pressure and water
volume can be regulated on the
machine by turning the button
for regulation of pressure / wa­ter volume (6).

70 Original Instructions

Poseidon 2

5 Fields of application and working
methods

5.1 General Effi cient high pressure cleaning is achieved by following a few

guidelines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly cho­sen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.

5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the

chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface be­ing cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be da maged.

5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical

effect may be required. Special wash brushes offer this supplemen­tary effect that removes stubborn dirt, traffi c fi lm or the like.

71

Poseidon 2

Original Instructions



6 After using your pressure washer

6.2 Winding up of electric
cable and high pressure
hose

up carefully.

1. Wind up the electric cable on
the dedicated hooks. Built-in

clip for good holding.

The lower hook can be

turned to release the electric
cable.

2. The high pressure washer
comes in two models: A) with
hook for storage of high pres­sure hose (14) - B) with a
hose reel (13).

6.1 Storing the washer The machine should be sto-

red in a frost-free room!

Pump, hose and accessories
should always be emptied of
water prior to storing as follows:

1. Stop the machine (turn the

start/stop switch (1) to posi­tion “O” and detach water
hose and accessory.

2. Restart the machine and

activate the trigger. Let the
machine run until no more
water runs through the spray
handle.

3. Stop the machine and un-

plug. Wind the electric cable
round the hooks placed on
the side of the machine.

4. Separate spray handle and

spray lance.

5. Machines without hose reel:
Detach high pres sure hose,
coil it up and place it on the
hose storage.

Machines with hose reel: Coil

the high pressure hose up on
the hose reel.

6. Place spray handle, nozzles
and other ac ces so ries in the
holders of the machine.

Should the machine by mistake
be frozen, let it thaw and check
it for damage.

NEVER START-UP A FROZEN
MACHINE.

Frost damages are not
covered by the guarantee!

6.3 Storage of accessories

The standard accessories
(spray handle, spray lance
(A) and nozzle cleaning tool)
can be stored on the pressure
washer.

To avoid accidents, the electric
cable and the high pressure
hose should always be wound

A

72 Original Instructions

Poseidon 2

WARNING! Always disconnect
the electrical plug from the
socket prior to maintenance or
cleaning.
To ensure a long and problem
free working life, please take
the following advice:

 Wash off water hose, high

pressure hose, spray lance
and accessories before
mounting.

 Clean the connectors of dust

and sand.

 Clean the nozzles.

Any repair should always be
made in an authorized work­shop with original spare parts.

7 Maintenance

7.1 Cleaning of water inlet
fi lter

Clean the water inlet fi lter regu­larly once a month or more fre­quently according to use. Care­fully loosen the fi lter with a pair
of pliers and clean it. Check that
it is intact before re-mounting it.

The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out various impurities,
as they will damage the pump
valves.

CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.

7.2 Cleaning of nozzle A clogging up in the nozzle

causes a pump pressure which
is too high. This is why cleaning
is required immediately.

1. Stop the machine and dis­connect the nozzle.

2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!

3. Flush the nozzle backwards
with water.

7.3 Cleaning of machine
vents

The machine should be kept
clean so as to let cooling air

7.4 Greasing of couplings

To ensure easy connection and
that o-rings do not dry up, the

pass freely through the ma­chine vents.

couplings should be greased
regularly.

73

Poseidon 2

Original Instructions

8 Trouble-shooting

Please ensure that you check the following before contacting the Nilfi sk-ALTO service organization:

Symptom Cause Recommended action

Machine refuses to start Machine not plugged in Plug in machine.

Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.

Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Valves dirty, worn out Clean and replace or refer to local Nilfi sk-
or stuck ALTO distributor
Pump seals worn out Clean and replace or refer to local Nilfi sk-
ALTO distributor.

Motor busses Low voltage or Activate the trigger of the spray handle.
low temperature

Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)

Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.

Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until
regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.

Machine often starts Contact your nearest Nilfi sk-ALTO Service
and stops by itself Centre.

Spray handle is leaking Replace seat/ball/O-ring in the valve of the
spray handle.

Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen

No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)

Pump pressure drops Button for regulation of Adjust the button to correct working pres-
pressure / water volume not sure.
correctly adjusted

In case problems other than the above occur, please contact your local Nilfi sk-ALTO distributor.

74 Original Instructions

Poseidon 2

9 Further information

9.1 Recycling the washer Make the old cleaner unusable

immediately.

1. Unplug the cleaner and cut
the electric cable.

Do not discard electrical appli­ances with household waste.

As specifi ed in WEEE Directive
2012/19/EC on old electrical

and electronic appliances, used
electrical goods must be col­lected separately and recycled
ecologically.

In case you have any ques­tions, please refer to local laws
and regulations or contact your
Nilfi sk-ALTO dealer for further
information.

9.2 Warranty conditions Our general conditions of busi-

ness are applicable with regard
to the guarantee.

Subject to change as a result of
technical advances.

10 Main Technical Data

Type Poseidon

2-20

Poseidon

2-22 T

Poseidon

2-22 XT

Poseidon

2-25 XT

Poseidon

2-29

Poseidon

2-29 XT

Rated pressure

bar/MPa

69/6.9 120/12 120/12 140/14 160/16 160/16

Cleaning impact

kg/force

2 2.2 2.2 2.5 2.9 2.9

Water flow

Qmax/

QIEC

l/min

-/2.4

gallon

8.6/7.8 8.6/7.8 10.2/9.0 10.2/9.5 10.2/9.5

Voltage/phase/frequency/
current

V/-/Hz/A

120/1/

60/15

230/1/

50/10

230/1/

50/10

230/1/

50/12.6

230/1/

50/14.5

230/1/

50/14.5

Max. water temperature

°C

60 60 60 60 60 60

Cable m 5 5 5 5 5 5

Pump

Rev./

min

3400 2800 2800 2800 2800 2800

Nozzle size

1/8"

475 350 350 370 370 370

Sound pressure level

dB(A)

77.4 76.1 76.1 77.4 73.5 79.7

Guaranteed sound power
level

dB(A)

92 91 91 92 88 94

Vibration according to
ISO 5349-1

m/s

2

< 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5

Weight kg 28.1 27.1 27.1 28.1 28.1 28.1

75

Poseidon 2

Original Instructions

11 EU Declaration of Conformity

Declaration of Conformity

Product: High Pressure Washer
Type:

Nilfi sk-ALTO Poseidon 2-17
Nilfi sk-ALTO Poseidon 2-20, 2-29
Nilfi sk-ALTO Poseidon 2-22 XT, 2-25 XT, 2-29 XT

Description: 120 V, 230 V, 1~, 50 Hz - IP X5
The design of the unit corre sponds to the follow-

ing pertinent regulations:

EC Machine Directive 2006/42/EC
EC Low-voltage Directive 2006/95/EC
EC EMV Directive 2004/108/EC

RoHS Directive 2011/65/EC
EC Noise Emission Directive 2000/14/EC

Applied harmonised standards: EN ISO 12100-1 (2004), EN ISO 12100-2 (2004)

EN 60335-2-79 (2006)
EN 55014-1 (2006), EN 55014-2 (2001), EN 61000-3-2
(2006)

Applied national standards and technical specifi -
cations:

BS EN 60335-2-79

Name and address of the person autho rised to
compile the technical fi le:

Anton Sørensen
General Manager, Technical Operations EAPC

Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby

Identity and signature of the person empowered
to draw up the declaration on behalf of the
manufacturer:

Anton Sørensen
General Manager, Technical Operations EAPC

Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby

Place and date of the declaration Hadsund, February 1, 2012

DENMARK

Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby
Tel.: [phone]
www.nilfi sk-advance.com

SALES COMPANIES

ARGENTINA

Nilfi sk-Advance srl.
Herrera 1855, 6 fl oor, Of. A-604
ZC 1293 – Ciudad Autónoma
de Buenos Aires – Argentina
www.nilfi sk-alto.com

AUSTRALIA

Nilfi sk-ALTO
Unit 1, 13 Bessemer Street Blacktown
NSW 2148 Australia
www.nilfi sk-alto.com.au

AUSTRIA

Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance GmbH
Metzgerstraße 68
A-5101 Bergheim/Salzburg
www.nilfi sk-alto.at

BELGIUM

Nilfi sk-Advance NV/SA
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070 Brussel
www.nilfi sk.be

CHILE

Nilfi sk-Advance S.A.
San Alfonso 1462, Santiago
www.nilfi sk.com

CHINA

Nilfi sk-Advance Cleaning Equipment
(Shanghai) Co Ltd.
No. 4189, Yindu Road
Xinzhuang Industrial Park
Shanghai 201108
www.nilfi sk.cn

CZECH REPUBLIC

Nilfi sk-Advance s.r.o.
Do Certous 1
VGP Park Horní Pocernice, Budova H2
CZ-190 00 Praha 9
www.nilfi sk.cz

DENMARK

Nilfi sk-ALTO Danmark
Industrivej 1
Hadsund, DK-9560
www.nilfi sk-alto.dk

FINLAND

Nilfi sk-Advance OY Ab
Koskelontie 23E
Espoo, FI-02920
www.nilfi sk.fi

FRANCE

Nilfi sk-Advance SAS
Division ALTO
BP 246
91944 Courtaboeuf Cedex
www.alto-fr.com

GERMANY

Nilfi sk-ALTO
Geschäftsbereich der Nilfi sk-Advance AG
Guido-Oberdorfer-Straße 10
89287 Bellenberg
www.nilfi sk-alto.de

GREECE

Nilfi sk-Advance A.E.
8, Thoukididou Str.
Argiroupoli,Athens, GR-164 52
www.nilfi sk.gr

HOLLAND

Nilfi sk-Advance B.V.
Versterkerstraat 5
1322 AN ALMERE
www.nilfi sk.nl

HONG KONG

Nilfi sk-Advance Ltd.
2001 HK Worsted Mills Ind’l Bldg.
31-39 Wo Tong Tsui St.
Hong Kong, Kwai Chung, N.T.
www.nilfi sk.com

HUNGARY

Nilfi sk-Advance Kereskedelmi Kft.
H-2310 Szigetszentmiklós-Lakihegy
II. Rákóczi Ferenc út 10.
www.nilfi sk.hu

INDIA

Nilfi sk-Advance India Limited
Pramukh Plaza, ‘B’ Wing, 4th fl oor, Unit No. 403
Cardinal Gracious Road, Chakala
Andheri (East), Mumbai 400 099
www.nilfi sk.com

IRELAND

Nilfi sk-Advance
1 Stokes Place
St. Stephen’s Green
Dublin 2, Ireland
www.nilfi sk-alto.ie

ITALY

Nilfi sk-Advance S.p.A.
Strada Comunale Della Braglia, 18
Guardamiglio, Lombardia, I-26862
www.nilfi sk.it

JAPAN

Nilfi sk-Advance Inc.
1-6-6 Kita-Shinyokohama
Kouhoku-Ku
Yokohama 223-0059
www.nilfi sk-advance.co.jp

KOREA

NIlfi sk-Advance Korea
471-4, Kumwon B/D 2F,
Gunja-Dong, Gwangjin-Gu, Seoul
www.nilfi sk-advance.kr

MALAYSIA

Nilfi sk-Advance Sdn Bhd
SD 33, Jalan KIP 10
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Malaysia
www.nilfi sk.com

MEXICO

Nilfi sk Advance de Mexico S. de R.L. de C.V.
Agustin M. Chavez 1, PB-004
Col. Centro Ciudad Santa Fe
C.P. 01210 México, D.F.
www.nilfi sk-advance.com.mx

NEW ZEALAND

Nilfi sk-Advance NZ Ltd
Danish House
6 Rockridge Avenue
Penrose Auckland NZ 1135
www.nilfi sk.com.au

NORWAY

Nilfi sk-Advance AS
Bjørnerudvejen 24
Oslo, N-1266
www.nilfi sk-alto.no

POLAND

Nilfi sk-Advance Sp. z.o.o
ul. 3-go Maja 8, Bud. B4
Pruszków, PL-05-800
www.nilfi sk-alto.pl

PORTUGAL

Nilfi sk-Advance, Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1o A
Sintra, P-2710-089
www.nilfi sk.pt

RUSSIA

Nilfi sk-Advance LLC
Vyatskaya str. 27, bld. 7, 1st fl oor
Moscow, 127015
www.nilfi sk.ru

SOUTH AFRICA

WAP South Africa (Pty) Ltd
12 Newton Street
1620 Spartan, Kempton Park
www.wap.co.za

SINGAPORE

Nilfi sk-Advance Pte Ltd
22 Tuas Avenue 2
Singapore 639453
www.nilfi sk.com

SPAIN

Nilfi sk-Advance, S.A.
Torre D’Ara
Passeig del Rengle, 5 Plta.10ª
Mataró, E-0830222
www.nilfi sk.es

SWEDEN

Nilfi sk-ALTO
Aminogatan 18
Mölndal, S-431 53
www.nilfi sk-alto.se

SWITZERLAND

NA Sondergger AG
Nilfi sk-ALTO Generalvertretung
Mühlestrasse 10
CH-9100 Herisau
www.nilfi sk-alto.ch

TAIWAN

Nilfi sk-Advance Ltd.
Taiwan Branch (H.K.)
No. 5, Wan Fang Road, Taipei
www.nilfi sk-advance.com.tw

THAILAND

Nilfi sk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Jomphol, Jatuchak
Bangkok 10900
www.nilfi sk.com

TURKEY

Nilfi sk-Advance A.S.
Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7
Ümraniye, Istanbul 34775
www.nilfi sk.com.tr

UNITED KINGDOM

Nilfi sk-ALTO
Bowerbank Way, Gilwilly Industrial Estate
Penrith, Cumbria
GB-CA11 9BQ
www.nilfi sk-alto.co.uk

UNITED ARAB EMIRATES

Nilfi sk-Advance Middle East Branch
SAIF-Zone, P. O. Box 122298
Sharjah
www.nilfi sk.com

USA

Nilfi sk-Advance
14600 21st Ave. North
Plymouth MN 55447-3408
www.nilfi sk-alto.us

VIETNAM

Nilfi sk-Advance Co., Ltd.
No.51 Doc Ngu Str. Lieu Giai Ward
Ba Dinh Dist. Hanoi
www.nilfi sk.com

HEAD QUARTER