Nilfisk-Advance C 120.3, C 125.3, C 130.1 X-TRA User Manual

Nil sk C 120.3
Nil sk C 125.3
Nil sk C 130.1 X-TRA

User Manual

Copyright © 2012 Nilfisk, Division of Nilfisk-Advance A/S

Nilfisk C 120.3 / C 125.3 / C 130.1

3

Original Instructions

Index

1 Safety precautions and warnings .............................................3

2 Description ...............................................................................5

3 Before you start using your pressure washer ...........................6

4 Operating your pressure washer ..............................................7

5 Fields of Application and working methods ..............................9

6 After using your pressure washer ...........................................11

7 Maintenance ...........................................................................13

8 Trouble Shooting ....................................................................15

9 Further information .................................................................16

10 Main Technical Data ...............................................................19

11 EC Declaration of Conformity .................................................20

1 Safety Precautions and Warnings

Symbols used to mark in­structions

Before starting
up your high­pressure washer
for the fi rst time,

this instruction
manual must be read through
carefully. Save the instructions
for later use.

Safety instructions
marked with this
symbol must be
observed to pre-

vent danger to persons.

This symbol is

used to mark safety

instructions that
must be ob-

served to prevent
damage to the machine and its
per formance.

This symbol
indicates tips

and instructions
to simplify work and to ensure a
safe operation.

Do not let children or people
who have not read the instruc­tion manual ope rate the ma­chine.

This appliance is not intended
for use by children or other
persons without assistance or
supervision if their physical,
sensory or mental capabili­ties prevent them from using it
safely. Children should be su­pervised to ensure that they do
not play with the appliance.

Before starting up your machine
please check it carefully for any
defects. If you fi nd any, do not
start up your machine and con­tact your Nilfi sk distributor.

Especially check:

 The insulation of the electric

cable should be faultless
and without any cracks. If the
electric cable is damaged, an
authorized Nilfi sk distributor
should replace it.

WARNING!

 High pressure jets can be

dangerous. Never direct the
water jet at persons, pets,
live electrical equipment or
the machine itself.

 Never try to clean clothes or

footwear on yourself or other
persons.

 Hold the spray lance fi rmly

with both hands. The spray
lance is affected by a thrust
of up to 16.4 N during ope–
ration.

 The operator and anyone in

the immediate vicinity of the
site of cleaning should take
action to protect themselves
from being struck by debris
dislodged during operation.
Wear goggles and protection
clothes during operation.

 This appliance has been de-

signed for use with cleaning
agents supplied or recom­mended by the manufacturer.
The use of other cleaning
agents or chemicals may
adversely affect the safety of
the appliance.

 To ensure the appliance

safety only use original spare
parts from the manufacturer
or approved by the manufac­turer.

 High pressure hoses, fi ttings



Nilfisk C 120.3 / C 125.3 / C 130.1

4

Original Instructions

and couplings are important
for the safety of the appli­ance. Only use hoses, fi ttings
and couplings recommended
by the manufacturer.

 Do not use the appliance

if a supply cord or impor­tant parts of appliance are
damaged, e.g. safety device ,
high pressure hose and trig­ger gun.

 Remove the plug from the

socket outlet during cleaning
or maintenance and when
replacing parts or converting
the machine to another func­tion.

 Appropriate ear protection

has to be used.

 Never use the machine in

an environment where there
could be a danger of explo­sion. If any doubt arises,
please contact the local
authorities.

 It is not allowed to clean

asbestos- containing surfaces
with high pressure.

 Do not spray fl ammable liq-

uids.

 Always switch off the mains

disconnecting switch when
leaving the machine unat­tended.

This high pressure washer

must not be used at tempera­tures below 0°C.

WARNING!

Inadequate extension cables
can be dangerous. If an exten­sion cable is used, it shall be
suitable for outdoor use, and
the connection has to be kept
dry and off the ground. It is rec­ommended that this is accom­plished by means of a cable
reel which keeps the socket at
least 60 mm above the ground.
Cables on extension lead
drums should always be com­pletely unwound to prevent the
cable from overheating.

Extension cables must comply
with the below-mentioned re­quirements for length and cable

dimensions.

1.0 mm² max. 12.5 m

1.5 mm² max. 20 m

2.5 mm² max. 30 m

 If the electric cable is

damaged, it must be re­placed by the manufacturer
or his service agent or simi­larly qualifi ed person in order
to avoid a hazard.

Mains power connection

The following should be ob­served when connecting the
high pressure washer to the
electric installation:
 Only connect the machine to

an installation with earth con­nection.

 The electric installation shall

be made by a certifi ed elec­trician and comply with IEC

364.

 It is recommended that the

electric supply to this ap­pliance should include a
residual current device that
will interrupt the supply if the
leakage current to earth ex­ceeds 30 mA for 30 ms.

Water connection

Connection to the public mains
according to regulations.

Machine not suit­able for connec­tion to the potable
water mains

This high pressure washer is
only allowed to be connected
with the drinking water mains,
when an appropriate backfl ow
preventer has been installed,
Type BA according to EN

1717. The backfl ow preventer
can be ordered under number

106411177. The length of the
hose between the backfl ow
preventer and the high pres-

sure washer must be at least
10 metres to absorb possible
pressure peaks (min diameter
½ inch).
Operation by suction (for ex­ample from a rainwater vessel)
is carried out without backfl ow
preventer. Recommended suc­tion set: 126411387.
As soon as water has fl own
through the BA valve, this water
is not considered to be drinking
water any more.

IMPORTANT! Only use wa­ter without any impurities. If

there is a risk of running sands
in the inlet water (i.e. from your
own well), an additional fi lter
should be mounted.

Safety devices

Locking device on spray gun
(7a) (see foldout at the end of

this manual):
The spray gun features a lock­ing device. When the pawl is
activated, the spray gun cannot
be ope rated.

Thermal sensor:

A thermal sensor protects the
motor against overloading. The
machine will restart after a few
minutes when the thermal sen­sor has cooled.

Pressure safety device

An integrated hydraulic safety
valve protects the system from
excessive pressure.

Nilfisk C 120.3 / C 125.3 / C 130.1

5

Original Instructions

2 Description

2.1 Application This high-pressure washer has

been developed for domestic
use within:

- Car, motorbike, boat, cara­van, trailer, patio/drive/fl ag­stones, woodwork, brickwork,
barbecue, garden furniture,
lawn mower

Section 5 describes the use of

the high-pressure washer for
vaious cleaning jobs.

Only use the high-pressure
washer for purposes described
in this manual.

The safety precautions must be
observed to prevent damage
to the machine, the surface to
be cleaned or severe personal
injuries.

2.2 Operation elements
and model survey

See illustration at the end of
this manual.

1 Start/stop switch
2 Water inlet (with fi lter)
3 High pressure connection
4 High pressure hose
5 Electric cable
6 Click & Clean spray lance
7 Spray gun with lock
8 Click & Clean Tornado® PR

nozzle

9 Click & Clean Powerspeed®

nozzle
10 Click & Clean foam sprayer
11 Nozzle cleaning tool
12 Trolley Handle
13 Hose reel (not standard)
14 Hose hook
15 Model tag
16 Warning sign
17 Cable hook

Specifi cations: See model tag
(15) of machine.

We reserve the right to alter the
specifi cations.

Nilfisk C 120.3 / C 125.3 / C 130.1

6

Original Instructions

3 Before you start using your
pressure washer



3.1 Mounting of trolley
handle and hose hook

1. Mount the trolley handle (12)
on the machine.

2. Mount the hose hook (14) on
the handle.

3.2 Mounting of trolley hand­le and hose reel (models
with hose reel)

1. Mount the trolley handle (12)
on the machine.

2. Mount the hose reel (13) on
the handle

3.3 Mounting of cable book
(C 130.1 X-TRA)

Click cable hooks (17) on to the
machine.

3.4 Mounting of quick
coupling

1. Screw the quick coupling
tight on to the water inlet (2).

Note: The inlet fi lter

must always be fi t-

ted in the water

inlet pipe to fi lter

out sand, lime stone

and other impurities as
these will damage the pump
valves.
Caution: Failure to fi t the fi lter
will invalidate the guarantee.

Nilfisk C 120.3 / C 125.3 / C 130.1

7

Original Instructions

3.5 Mounting of high pres­sure hose

Attach the high pressure hose
(4) to the spray gun (7).

Detach the high pressure hose
by pressing the pawl (A).

4 Operating your pressure washer

4.1 Connection of high pres­sure hose

1. Mount the high pressure
hose on the outlet (3).

6

7

4.2 Mounting of spray
lance and Click & Clean

nozzles

1. Push the spray lance (6) into
the spray gun (7) and screw
it on.

Note: The
spray lance (6)

has a built-in low
pressure nozzle that can be
used for fl ushing away dirt.

2. Attach the nozzle.

Warning: When

attaching the Click &

Clean nozzles, the

pawl on the side

of the spray lance

should come out again.

Note: The Tor-

nado® PR nozzle

and the foam

sprayer feature a swivel lock,
which must be positioned in the
hole in the Click & Clean spray
lance.

Press the pawl to detach the
Click & Clean nozzle.



Nilfisk C 120.3 / C 125.3 / C 130.1

8

Original Instructions

4.3 Water connection An ordinary 1/2" garden hose of
min. 10 m and max. 25 m will

be suitable.

NOTE: Connec­tion to the public
mains according
to regulations.

IMPORTANT!
Only use water
without any

impurities. If there is a risk

of running sands in the inlet
water (i.e. from your own well),
an additional fi lter should be
mounted.

1. Let the water run through the
water hose before connecting
it to the machine to prevent
sand and dirt from penetrat­ing the machine.

Note: Check that the fi lter is

fi tted in the water inlet pipe
and that it is not clogged up.

2. Connect the water hose to
the water supply by means
of the quick connector (inlet
water, max. pressure: 10 bar,
max. temperature: 40°C).

3. Turn on the water.

4.4 Start and stop of the
machine (when con-

nected to a water supply)

The spray lance is affected
by a thrust during operation ­therefore always hold it fi rmly
with both hands. IMPORTANT:

Point the nozzle at the
ground.

1. Check that the machine is in
upright position.

NOTE: Do not place the

machine in high grass!

2. Release the trigger lock.

3. Activate the trigger of the
spray gun and let the water
run until all air has escaped
from the water hose.

4. Turn the start/stop switch (1)
to position"I".

5. Activate the trigger of the
spray gun.

Always adjust the distance and
thus the pressure of the nozzle
to the surface, which is to be
cleaned.

Do not cover the machine
during operation.

Note: If the ma­chine is left or not

used for 5 min­utes, it must be switched off on
the start/stop switch "O" (1):

1. Turn the start/stop switch (1)

to position"O".

2. Disconnect the electrical plug

from the socket.

3. Shut off the water supply and

activate the trigger to relieve
the machine of pressure.

4. Lock the spray gun.

When releasing the trigger of
the spray gun, the machine
automatically stops. The ma­chine will start again when you
re-activate the spray gun.

Nilfisk C 120.3 / C 125.3 / C 130.1

9

Original Instructions

4.5 Start the machine (when
connected to open con­tainers (suction mode))

The washer can take in water
from a rain water tank as an
example. The hose for the wa­ter supply must not be too long,
approx. 5 m.

Make sure that the water tank
is not placed on a lower level
than the machine.

1. Place the other end of the
water hose in the water tank.
Use an external fi lter if the
water contains impurities.

2. Turn the start/stop switch (1)
to position"I".

3. Activate the trigger of the
spray gun and let the water
run, until the air has escaped
from the water hose and the
pump.

4. Mount spray lance and
nozzle.

4.6 Pressure regulation on
the TORNADO

®

PR-

nozzle

The pressure can be regulated
on the TORNADO® PR nozzle.

Lavtryk

Højtryk

High pressure

Low pressure

5 Fields of application and working
methods

5.1 General Effi cient high presure cleaning is achieved by following a few guide-

lines, combined with your own personal experience of specifi c
cleaning tasks. Accessories and detergents, when correctly cho­sen, can increase the effi ciency of your pressure washer. Here is
some basic information about cleaning.

5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the

chemical product is in direct contact with the dirt. Detergents are
applied from bottom to top, for example on a car bodywork, in order
to avoid "super clean" areas, where the detergent collects in higher
concentration and streams downwards. Let the detergent work for
several minutes before rinsing but never let it dry on the surface be­ing cleaned. Note: It is important that the detergents do not dry up.
Otherwise the surfac that has to be cleaned can be da maged.

5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical

effect may be required. Special wash brushes offer this supplemen­tary effect that cuts through dirt (especially by car washing).

Nilfisk C 120.3 / C 125.3 / C 130.1

10

Original Instructions

5.2 Typical fi elds of application

Below you will fi nd a description of a lot of cleaning tasks which can be solved by a pressure washer
from Nilfi sk in association with accessories and detergents.

Task Accessories ‘Click

& Clean’

Cleaning method

Car Car nozzle,

auto brush,
underchassis

nozzle,

Foam sprayer,

Car Combi Cleaner

1. Apply Car Combi Cleaner with the foam sprayer. Always
start from the bottom and work upwards. Let Car Combi

Cleaner act for at least 5 min.

2. Wash the car with the car nozzle, which has been optimized for
quick and gentle cleaning of enamelled surfaces (the jet is wider
and not so sharp). Start at the front of the car and work back­wards to avoid water from penetrating by the door mouldings.

3. Use the brush for removal of traffi c fi lm which is not removed by the
nozzle. If the car is very dirty, apply Car Combi Clean er again.

4. Attach the undercarriage nozzle and clean undercarriage and
wheel arches.

5. Remove water from the surface of the car with the scraper
on the car brush. Make sure that all grains of sand etc. have
been removed before using the scraper. Wipe with a wash lea­ther where the scraper cannot reach.

Rims, alu-

minium

Rim brush,
auto nozzle,
atomizer,
Alu Cleaner

Apply Alu Cleaner with an automizer. Let it act for approx.

5 min. and wash with the rim brush. For steel rims, use Car Com­bi Cleaner. Use the foam sprayer and wash with rim brush.

Be careful! The high pressure jet may damage the tyres.

Flagstones,
concrete

fl oors and
other hard
surfaces

Powerspeed®
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner

Wash towards outlets or the like. On surfaces with moss or
algae you may start by applying Stone & Wood Cleaner with
the foam sprayer. Wash before the soap dries. Another
more effective and quicker method is to use the Patio
Cleaner. Thus you will also avoid splashes.

Garden

furniture,
wood

Wood Cleaner
Garden brush

Apply Wood Cleaner and wash before the soap dries.
NOTE: Use the garden brush to clean off the dirt.

Brickwork,
Wood work

Powerspeed®
nozzle,
Stone & Wood
Cleaner,
Patio Cleaner

Same method as for fl agstones, but be careful - bad joints and

wood may be damaged by high pressure. You may choose only
to use the Tornado® nozzle. Adjust the distance (pressure) to
the quality of the joints and the wood. Patio Cleaner can also be
used on vertical surfaces.

Gutter Underchassis spray

lance

Wash the gutter with the nozzle. Always wash towards

downpipes. Beware not to spray under the roofi ng.

Cleaning

of drain
pipes, out­lets, down
pipes etc.

Tube cleaner Push the tube cleaner approx. ½ m (to mark) into a tube or drain

and activate the trigger of the spray handle. The nozzle opening
turning backwards will pull the cleaner through the tube. The
nozzle will break down the „plug“ and fl ush the dirt backwards.

Rust, paint Water/sandblasting

equipment

Mount the water/sand blasting equipment and rust and paint

is effi ciently and quickly removed. Beware not to damage the
surface to be sandblasted.

Green-

house

Tornado® PR nozzle
brush, Stone &

Wood Cleaner

Wash with high pressure and maybe a brush. You may use Stone

& Wood Cleaner to remove moss and algae.

Garden

tools, lawn
mover

Tornado® PR noz-

zle, Powerspeed®
nozzle, multiangle
adaptor, Metal
Cleaner

Rinse the worst dirt off with the nozzle. Apply Metal Cleaner with

the foam sprayer and let it act for approx. 5 min. Wash with the
nozzle. You may use the multiangle adaptor for hard to get at
areas to avoid splashing.

Nilfisk C 120.3 / C 125.3 / C 130.1

11

Original Instructions



6 After using your pressure washer

6.2 Winding up of electric
cable and high pressure
hose

To avoid accidents, the electric
cable and the high pressure
hose should always be winded
carefully up.

Wind up the electric cable and
the high pressure hose on the
appropriate hooks. Built-in clip
for good holding.

The high pressure washer
comes in two models: A) with
hook for storage of high pres­sure hose (14) - B) with a hose
reel (13), where the hose is
pushed into the reel and after­wards winded up.

6.1 Storing the washer The machine should be sto-

red in a frost-free room!

Pump, hose and accessories
should always be emptied of
water prior to storing as follows:

1. Stop the machine (turn
the start/stop switch (1) to
position"O") and detach wa­ter hose and accessory.

2. Restart the machine and
activate the trigger. Let the
machine run until no more
water runs through the spray
gun.

3. Stop the machine, unplug
and wind up hose and cable.

4. Place spray handle, nozzles
and other accessories in the
holders of the machine.

Should the machine by mistake
be frozen, it will be necessary
to check it for damage.

NEVER START-UP A FROZEN
MACHINE.

Frost damages are not
covered by the guarantee!

C 130.1 X-TRA

C 120.3
C 125.3

C 120.3
C 125.3

C 130.1 X-TRA

Nilfisk C 120.3 / C 125.3 / C 130.1

12

Original Instructions

6.4 Wall storage

The pressure washer can be
stored on a wall on a special
wall hook (not standard).

Only mount the wall hook on a
sturdy wall. Adjust the length
of the screws and size of rawl­plugs to the type of wall.

On the wall hook garden/rim
brush (a) foam sprayer (b),
Click & Clean brush (c) and
Click & Clean nozzles (d) can
be stored.

Note: For this
product the wall
hook can only be

used as storage.

Important: The

bearing capacity
of the wall hook

is max. 30 kg.



A

C

B

D

6.3 Storage of accessories

The standard accessories
(spray gun, spray lance, noz­zles and foam sprayer) can be
stored on the pressure washer.

The nozzle cleaning tool can
also be stored on the product.

C 130.1 X-TRA

C 120.3
C 125.3

Nilfisk C 120.3 / C 125.3 / C 130.1

13

Original Instructions

WARNING! Always disconnect
the electrical plug from the
socket prior to maintenance or
cleaning.

To ensure a long and problem
free working life, please take
the following advice:

 Wash out water hose, high

pressure hose, spray lance
and accessories before
mounting.

 Clean the connectors of dust

and sand.

 Make sure that no sand or

dirt is blocking the movement
of the pawl on the Click &
Clean spray lance. Rinse ac­cording to requirement.

 Rinse the detergent spraying

attachment after use.

 Clean the nozzles.

Any repair should always be
made in an authorized work­shop with original spare parts.

7 Maintenance

7.1 Cleaning of water inlet
fi lter

Clean the water inlet fi lter
regularly once a month or more
frequently according to use.
Carefully loosen the fi lter with a
screwdriver and clean it. Check
that it is intact before re-mount­ing it.

The inlet fi lter must always be
fi tted inside the water inlet pipe
to fi lter out sand, limestone and
other impurities, as they will
damage the pump valves.

CAUTION: Failure to fi t the fi lter
will invalidate the guarantee.

7.2 Cleaning of nozzle A clogging up in the nozzle

causes a pump pressure which
is too high. This is why cleaning
is required immediately.

1. Stop the machine and dis­connect the nozzle.

2. Clean the nozzle. IMPOR-
TANT: The cleaning tool (11)
should only be used when
the nozzle is detached!

3. Flush the nozzle backwards
with water.

Nilfisk C 120.3 / C 125.3 / C 130.1

14

Original Instructions

7.3 Cleaning of machine
vents

The machine should be kept
clean so as to let cooling air
pass freely through the ma­chine vents.

7.4 Greasing of couplings

To ensure an easy connec­tion and that o-rings do not dry
up, the couplings should be
greased regularly.

Nilfisk C 120.3 / C 125.3 / C 130.1

15

Original Instructions

8 Trouble-shooting

To avoid unnecessary disappointments, you should check the following before contacting the Nilfi sk
service organization:

Symptom Cause Recommended action

Machine refuses to start Machine not plugged in Plug in machine.

Defective socket Try another socket.
Fuse has blown Replace fuse. Switch off other machines.
Defective extension cable Try without the extension cable.

Fluctuating pressure Pump sucking air Check that hoses and connections are air-
tight.
Valves dirty, worn out Clean and replace or refer to local Nilfi sk
or stuck distributor
Pump seals worn out Clean and replace or refer to local Nilfi sk
distributor.

Motor busses Low voltage or Activate the trigger of the spray gun.
low temperature

Machine stops Fuse has blown Replace fuse. Switch off other machines.
Incorrect mains voltage Check that the mains voltage corresponds
to specifi cation on the model tag.
Thermal sensor activated Leave the washer for 5 minutes to cool
down.
Nozzle partially blocked Clean the nozzle (see section 7.2)

Fuse blows Fuse too small Change to an installation higher than the
amp. consumption of the machine.
You may try without the extension cable.

Machine pulsating Air in inlet hose/pump Allow machine to run with open trigger until
regular working pressure resumes.
Inadequate supply of Check that the water supply corresponds to
mains water specifi cations required (see model tag)
NB! Avoid using long, thin hoses (min. 1/2")
Nozzle partially blocked Clean the nozzle (see section 7.2)
Water fi lter blocked Clean the fi lter (see section 7.1)
Hose kinked Straighten out hose.

Machine often starts Pump/spray gun is Contact your nearest Nilfi sk Service
and stops by itself leaking Centre.

Machine starts, but Pump/hoses or accessory Wait for pump/hoses or accessory to thaw.
no water comes out frozen

No water supply Connect inlet water.
Water fi lter blocked Clean the fi lter (see section 7.1)
Nozzle blocked Clean the nozzle (see section 7.2)

In case problems other than the above occur, please contact your local Nilfi sk distributor.

UK:

Customer Services at Penrith - 01768 868995

Nilfisk C 120.3 / C 125.3 / C 130.1

16

Original Instructions

9 Further information

9.1 Recycling the washer Make the old cleaner unusable

immediately.

1. Unplug the cleaner and cut
the electric cable.

Do not discard electrical appli­ances with household waste.

As specifi ed in European Direc­tive 2002/96/EC on old electri­cal and electronic appliances,
used electrical goods must
be collected separately and
recycled ecologically.

Contact your local authorities or
your nearest dealer for further
information.

9.2 Warranty conditions Nilfi sk guarantees high pres­sure washers for domestic use
for 2 years. If your high pres­sure washer or ac ces so ries are
handed in for repair, a copy of
the receipt must be enclosed.
Guarantee repairs are being
made on the following con di­t ions:
 that defects are attributable

to fl aws or defects in materi­als or workmanship. (wear
and tear as well as misuse
are not covered by the gu a r­an tee).

 that the directions of this

instruction manual have been
thoroughly observed.

 that repair has not been car-

ried out or attempted by oth­er than Nilfi sk-trained service
staff.

 that only original accessories

have been applied.

 that the product has not been

exposed to abuse such as
knocks, bumps or frost.

 that only water without any

impurities has been used.

 that the high pressure wash-

er has not been used for
rental nor used com mer cial ly
in any other way.

Repairs under this guarantee
include replacement of defec­tive parts, exclusive of packing
and postage/carriage. Besides,
we refer to your national law of
sale.

The machine should be for­warded to one of the service
centres of the Nilfi sk organisa­tion with description/spe ci fi ca­ ti on of the fault.

Repairs not covered by the
guarantee conditions will be
invoiced. (I.e. malfunctions due
to Causes men ti o ned in section
Troubleshooting Chart of the
instruction manual).

Nilfisk C 120.3 / C 125.3 / C 130.1

17

Original Instructions

9.3 Accessories

Only use original accessories.

Click & Clean
Car nozzle

Special nozzle for enameled surfaces. Optimal distance: 30

- 50 cm.

Click & Clean
Undershassis
nozzle

90° angled special nozzle for undercarriage and wheel arches.
Integrated guide shoes.

Click & Clean
Multiangle
adaptor

Adjusted in angles from 0° - 90° for better working posture and
cleaning of hard to get at places as for instance barrels or the
underside of the lawn mower. Fits all nozzles.

Click & Clean
Brushes

For cars and other surfaces. Available in more shapes.

Extension hose

7 m extension hose increasing the working range.

Underchassis
spray lance

Special spray lance for washing your car underneath.

Drain & Tube
cleaner

15 m long tube cleaner for the cleaning of tubes and drains.

Water-sand­blasting equip­ment

For removal of paint and rust. Sand available from do-it-your­self shops.

Patio Plus

Equipment for quick cleaning of patio/drive/fl agstones.

Garden brush

Rotary brush for cleaning of wooden surfaces.

Rim brush

Rotary brush for cleaning of wheel rims.

Wall hook

For suspension of your high pressure washer on the wall.

Rotary brush

For cleaning vehicles and other surfaces.

Water suction
kit

For removal of large amounts of water from e.g. garden
pounds.

Nilfisk C 120.3 / C 125.3 / C 130.1

18

Original Instructions

Detergents

Stone & Wood Cleaner

For fl agstones, brick- and woodwork. Suitable for moss and algae.

Plastic Cleaner

For plastic and synthetic materials such as garden furniture.

Metal Cleaner

For cleaning of metal such as garden tools.

Car Combi Cleaner

For cars etc. With rinsing wax.

Alu Cleaner

For surfaces of aluminium. Applied with an atomizer.

Oil & Grease Cleaner

For cleaning of grease and oil on motors for instance. Applied with
an atomizer.

Wood Cleaner

For cleaning of wooden surfaces incl. of wooden garden furniture.

Nilfisk C 120.3 / C 125.3 / C 130.1

19

Original Instructions

Type C 120.3 C 125.3 C 130.1

Electrical Specification

Rated voltage V 230 230 230

Rated frequency Hz 50 50 50

Rated power consumption kW 1,650 1,800 1,700

Current A 7.2 7.8 7.8

Protection class

Class I/
Class II

Class II Class II Class I

Protection degree IP xx IPX5 IPX5 IPX5

Hydraulic specification

Rated pressure MPa/bar 10/100 10.5/105 11.5/115

Max. pressure MPa/bar 12/120 12.5/125 13/130

Rated water flow l/min/l/h 5.8/350 5.8/350 6.3/380

Max. water flow l/min/l/h 8.6/520 8.6/520 7.3/440

Max. water inlet pressure Mpa/bar 1/10 1/10 1/10

Max. water inlet temperature °C 40 40 40

Max. water inlet temp. suction mode °C 20 20 20

Weight kg 8.9 9 15.8

Hand-arm vibration according to ISO 5349-1:

Standard nozzle m/s

2

< 2.5 ±1 < 2.5 ±1 < 2.5 ±1

Sound pressure level L

pA

in accordance with

ISO 3744

dB(A) 78 ±3 78 ±3 66.4 ±3

Guaranteed sound power level L

WA in

accordance with 2000/14/EC

dB(A) 92 92 84

10 Main Technical Data

Nilfisk C 120.3 / C 125.3 / C 130.1

20

Original Instructions

11 EU Declaration of Conformity

EU Declaration of Conformity

Product: High Pressure Washer
Type: Nilfi sk C 120.3, C 125.3, C 130.1

and accessory variants of above-mentioned types

Description: 230 V 1~, 50 Hz - IP X5
The design of the unit corre sponds to

the following pertinent regulations:

EC Machine Directive 2006/42/EC
EC Low-voltage Directive 2006/95/EC
EC EMC Directive 2004/108/EC

Applied harmonised standards: EN 60335-2-79
Applied national standards and techni-

cal specifi cations:

IEC 60335-2-79

Name and address of the person autho­rised to compile the technical fi le:

Anton Sørensen
General Manager, Technical Operations EAPC

Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby

Identity and signature of the person
empowered to draw up the declaration
on behalf of the manufacturer:

Anton Sørensen
General Manager, Technical Operations EAPC

Nilfi sk-Advance A/S
Sognevej 25
DK-2605 Brøndby

Place and date of the declaration Hadsund, October 1, 2011

11

Web: http://www.nilfi sk.com

HEAD QUARTER

DENMARK

Nilfi sk-Advance Group
Sognevej 25
DK-2605 Brøndby
Tel.: [phone]
E-mail: kundeservice.dk@nilfi sk.com

SALES COMPANIES

AUSTRIA

Geschäftsbereich der Nilfi sk Advance GmbH
Metzgerstrasse 68
A-5101 Bergheim/Salzburg
Tel.: [phone]
E-mail: info.at@nilfi sk.com
Web: http://www.consumer.nilfi sk.at

BELGIUM

Nilfi sk-Advance NV/SA.
Riverside Business Park
Boulevard Internationale 55
Bruxelles 1070
Tel.: [phone]
Web: http://www.nilfi sk.be

CHILE

Nilfi sk-Advance de Chile
San Alfonso 1462
Santiago
Tel.:[phone]
E-mail: Pablo.Noriega@nilfi sk.com

CHINA

Nilfi sk-Advance Cleaning Equipment (Shanghai) Ltd.
No. 4189 Yindu Road
Xinzhuang Industrial Park
Shanghai 201108
Tel: [phone]
E-mail: info.sha-cn@nilfi sk.com
Web: http://www.nilfi sk.cn

CZECH REPUBLIC

Nilfi sk-Advance s.r.o.
VGP Park Horní Pocernice
Budova H2, Do Certous 1
Praha 190 00
Tel.: [phone]
E-mail: info@nilfi sk.cz
Web: http://www.nilfi sk.cz

DENMARK

Nilfi sk-ALTO Danmark
Industrivej 1
9560 Hadsund
Tel.: [phone]
E-mail: salg.dk@nilfi sk-alto.com
Web: http://www.nilfi sk.dk

FINLAND

Nilfi sk-Advance Oy Ab
Koskelontie 23E
02920 Espoo
Tel.: [phone]
Web: http://www.nilfi sk.fi

FRANCE

Nilfi sk-Advance
26 Avenue de la Baltique
Villebon sur Yvette
91944 Courtaboeuf Cedex
Tel.: [phone]
E-mail: info.fr.@nilfi sk-advance.fr
Web: http://www.nilfi sk.fr

GERMANY

Nilfi sk-ALTO
Guido-Oberdorfer-Strasse 10
89287 Bellenberg
Tel.: [phone]
E-mail: info-consumer.de@nilfi sk.com
Web: http://www.nilfi sk.de

GREECE

Nilfi sk-Advance SA
8, Thoukididou str.
164 52 Argiroupoli
Tel.: [phone]

E-mail: info@nilfi sk.gr
Web: http://www.nilfi sk.gr

HOLLAND

Nilfi sk-Advance
Versterkerstraat 5
1322 AN Almere
Tel.: [phone]
E-mail: info.nl.@nilfi sk.com
Web: http://www.nilfi sk.nl

HONG KONG

Nilfi sk-Advance Ltd.
Room 2001 HK Worsted Mills
Industrial Building
31-39 Wo Tong Tsui Street
Kvai Chung, NT
Tel.: [phone]

HUNGARY

Nilfi sk-Advance Kereskedelmi Kft.
H-2310 Szigetszentmilós
Lakihegy, II. Rákóczi Ferenc út 10
Tel: [phone]
Web: http://www.nilfi sk.hu

INDIA

Nilfi sk-Advance India Limited
Pramukh Plaza, “B” Wing, 4th fl oor
Unit No. 403
Cardinal Gracious Road
Chakala, Andheri (East)
Mumbai - 400 099
Tel.: [phone]

IRELAND

Nilfi sk-Advance
1 Stokes Place
St. Stephen’s Green
Dublin 2
Tel.: [phone]

ITALY

Nilfi sk-Advance SpA
Strada Comunale della Braglia, 18
26862 Guardamiglio (LO)
Tel.: [phone]
Web: http://www.nilfi sk.it

JAPAN

Nilfi sk-Advance Inc.
1-6-6 Kita-shinyokohama, Kouhoku-ku
Yokohama, 223-0059
Tel.: [phone]

MALAYSIA

Nilfi sk-Advance Sdn Bhd
Sd 14, Jalan KIP 11
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Tel.: [phone]

MEXICO

Nilfi sk-Advance de Mexico, S. de R.L. de C.V.
Agustín M. Chavez No. 1, PB ofi cina 004
Col. Centro de Ciudad Santa Fe
01210 Mexico, D.F.
Tel: [phone] (switchboard)
E-mail: [e-mail]

NEW ZEALAND

Nilfi sk-Advance Limited
Danish House
6 Rockridge Avenue
Penrose, Auckland 1135
Tel.: [phone]
Web: http://nilfi sk.com.au

NORWAY

Nilfi sk-Advance AS
Bjørnerudveien 24
1266 Oslo
Tel.: [phone]
Web: http://www.nilfi sk.no

POLAND

Nilfi sk-Advance Sp. z.o.o.
Millenium Logistic Park
ul. 3-go Maja 8, Bud. B4
05-800 Pruszków
Tel.: [phone]
E-mail: biuro@nilfi sk.pl
Web: http://www.nilfi sk.pl

PORTUGAL

Nilfi sk-Advance
Sintra Business Park
Zona Industrial Da Abrunheira
Edifi cio 1, 1° A

P2710-089 Sintra
Tel.: [phone]
Web: http://www.nilfi sk.pt

RUSSIA

Нилфиск-Эдванс
127015 Москва

Вятская ул. 27, стр. 7
Россия

Tel.: [phone]

E-mail: info@nilfi sk.ru
Web: http://www.nilfi sk.ru

SOUTH KOREA

NIlfi sk-Advance Korea
471-4, Kumwon B/D 2F,
Gunja-Dong, Gwangjin-Gu,
Seoul
Tel: [phone]

SOUTH AFRICA

WAP South Africa (Pty) Ltd
12 Newton Street
1620 Spartan, Kempton Park
Tel.: [phone]
E-mail: [e-mail]

SPAIN

Nilfi sk-Advance S.A.
Torre D’Ara
Paseo del Rengle, 5 Pl. 10
08302 Mataró
Tel.: [phone]
E-mail: mkt.es@nilfi sk.com
Web: http://www.nilfi sk.es

SWEDEN

Nilfi sk-ALTO Sverige AB
Aminogatan 18
431 04Mölndal
Tel.: [phone]
E-mail: info.se@nilfi sk.com
Web: http://www.nilfi sk.se

SWITZERLAND

Nilfi sk-Advance AG
Ringstrasse 19
Kirchberg/Industrie Stelz
9500 Wil
Tel.: [phone]
Web: http://www.nilfi sk.ch

TAIWAN

Nilfi sk-Advance
Taiwan Branch (H.K.)
No. 5, Wan Fang Road
Taipei
Tel.: [phone]
Web: http://www.nilfi sk-advance.com.tw

THAILAND

Nilfi sk-Advance Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Ladyao, Jatuchak, Bangkok 10900
Tel.: [phone]

TURKEY

Nilfi sk-Advance A.S.
Serifali Mh. Bayraktar Bulv.
Sehit Sk. No: 7
Ümraniye
Istanbul
Tel.: [phone]
E-mail: info.tr@nilfi sk-advance.com
Web: http://www.nilfi sk.com.tr

UNITED KINGDOM

Nilfi sk (A Division of Nilfi sk-Advance Ltd.)
Bowerbank Way
Gilwilly Industrial Estate, Penrith
Cumbria CA11 9BQ
Tel: [phone]
Web: http://www.nilfi sk.co.uk

UNITED ARAB EMIRATES

Nilfi sk-Advance Middle East Branch
SAIF-Zone
P.O. Box 122298
Sharjah
Tel.: [phone]

VIETNAM

Nilfi sk-Advance Representative Offi ce
No. 51 Doc Ngu Str.
Ba Dinh Dist.
Hanoi
Tel.: [phone]
E-mail: nilfi [e-mail]