NILFISK AX 651 Combi EDS Installation Manual

™

Adphibian AX 651 Combi EDS

Instructions for Use Instrucciones de uso

Advance Models: 56317000 Nilﬁ sk Models: 56317003

A-English B-Español

12/07 Form No. 56041711

TABLE OF CONTENTS

Page

Introduction .....................................................................................................................A-4

Parts and Service ...........................................................................................................A-4

Nameplate ......................................................................................................................A-4

Unpacking the Machine ..................................................................................................A-4

Cautions and Warnings ..................................................................................................A-5

Consignes de prudence et de sécurité ...........................................................................A-6

Know Your Machine ............................................................................................... A-7 - A-8

Control Panel ....................................................................................................... A-9 - A-10

Preparing the Machine for Use

Batteries ....................................................................................................................... A-11

Installing the Brushes ...................................................................................................A-12

Filling the Solution Tank ................................................................................................A-12

Pre-Spraying the Carpet ...............................................................................................A-13

Plan for Cleaning .......................................................................................................... A-13

Squeegee Installation ................................................................................................... A-13

Detergent (AXP/EDS) System .................................................................................A-14-15

ENGLISH / A-3

Operating the Machine

Extracting Operation .....................................................................................................A-16

Scrubbing Operation .....................................................................................................A-16

Using Attachments ........................................................................................................ A-17

After Use .......................................................................................................................A-18

Maintenance Schedule ................................................................................................. A-18

Servicing the Vacuum Motors .......................................................................................A-18

Lubricating the Machine ...............................................................................................A-18

Maintenance

Charging the Batteries (Wet) ........................................................................................A-19

Checking the Battery Water Level ................................................................................ A-19

Charging the Batteries (Gel) .........................................................................................A-19

Vacuum Shoe Maintenance ..........................................................................................A-20

Spray Nozzle Maintenance ........................................................................................... A-20

Power Brush Maintenance ...........................................................................................A-20

Servicing the Squeegee ...............................................................................................A-21

Adjusting the Squeegee ...............................................................................................A-21

Servicing the Recovery Tank Switch ............................................................................A-22

Troubleshooting

Circuit Breaker Tripping ................................................................................................A-23

Poor Water Pickup ........................................................................................................ A-23

Squeegee Streaks ........................................................................................................ A-23

No Solution Flow ..........................................................................................................A-23

Scrub Deck Raises While Scrubbing ............................................................................A-23

No Detergent Flow (AXP/EDS) ..................................................................................... A-23

Technical Speciﬁ cations ............................................................................................... A-24

Adphibian™ / AX 651 Combi EDS - 56041711 - A-3

A-4 / ENGLISH

INTRODUCTION

This manual will help you get the most from your Nilﬁ sk-Advance automatic scrubber / carpet extractor. Read it thoroughly before operating the machine.

Note: Bold numbers and letters in parentheses indicate an item illustrated on pages 7-10 unless otherwise noted.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Nilﬁ sk-Advance Service Center, who employs factory trained service personnel, and maintains an inventory of Nilﬁ sk-Advance original replacement parts and accessories.

Call the NILFISK-ADVANCE DEALER named below for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

(Dealer, afﬁ x service sticker here.)

NAMEPLATE

The Model Number and Serial Number of your machine are shown on the Nameplate on the machine. This information is needed when ordering repair parts for the machine. Use the space below to note the Model Number and Serial Number of your machine for future reference.

Model Number ___________________________________________

Serial Number ___________________________________________

UNCRATE THE MACHINE

When the machine is delivered, carefully inspect the shipping packaging and the machine for damage. If damage is evident, save the shipping carton (if applicable) so that it can be inspected. Contact the Nilﬁ sk-Advance Customer Service Department immediately to ﬁ le a freight damage claim. Refer to the unpacking instruction sheet included with the machine to remove the machine from the pallet.

A-4 - 56041711 - Adphibian™ / AX 651 Combi EDS

ENGLISH / A-5

CAUTIONS AND WARNINGS SYMBOLS

Nilﬁ sk-Advance uses the symbols below to signal potentially dangerous conditions. Read this information carefully and take the necessary steps to protect personnel and property.

DANGER!

Is used to warn of immediate hazards that will cause severe personal injury or death.

WARNING!

Is used to call attention to a situation that could cause severe personal injury.

CAUTION!

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.

Read all instructions before using.

GENERAL SAFETY INSTRUCTIONS

Speciﬁ c Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.

WARNING!

• This machine should only be used by properly trained and authorized persons.

• While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills. Clean only while ascending

(driving up) the ramp.

• Keep sparks, ﬂ ame and smoking materials away from batteries. Explosive gases are vented during normal operation.

• Charging the batteries produces highly explosive hydrogen gas. Charge batteries only in well-ventilated areas, away from open ﬂ ame. Do not

smoke while charging the batteries.

• Remove all jewelry when working near electrical components.

• Turn the key switch off (O) and disconnect the batteries before servicing electrical components.

• Never work under a machine without safety blocks or stands to support the machine.

• Do not dispense ﬂ ammable cleaning agents, operate the machine on or near these agents, or operate in areas where ﬂ ammable liquids exist.

• Do not clean this machine with a pressure washer.

• Do not operate this machine on ramps or inclines of more than a 2 percent gradient.

• Only use the brushes provided with the appliance or those speciﬁ ed in the instruction manual. The use of other brushes may impair safety.

CAUTION!

• This machine is not approved for use on public paths or roads.

• This machine is not suitable for picking up hazardous dust.

• When operating this machine, ensure that third parties, particularly children, are not endangered.

• Before performing any service function, carefully read all instructions pertaining to that function.

• Do not leave the machine unattended without ﬁ rst turning the key switch off (O), removing the key and securing the machine.

• Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels.

• Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.

• Use caution when moving this machine in below freezing temperature conditions. Any water in the solution, recovery or detergent tanks or in

the hose lines could freeze, causing damage to valves and ﬁ ttings. Flush with windshield washer ﬂ uid.

• The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries should be safely done in

accordance with your local environmental regulations.

• Do not use on surfaces having a gradient exceeding that marked on the machine.

• All doors and covers are to be positioned as indicated in the instruction manual before using the machine.

• Refer to the battery charger OEM product manual for additional speciﬁ c battery charger warnings.

SAVE THESE INSTRUCTIONS

Adphibian™ / AX 651 Combi EDS - 56041711 - A-5

A-6 / ENGLISH

CONSIGNES DE PRUDENCE ET DE SECURITE SYMBOLES

Les symboles reproduits ci-dessous sont utilisés par Nilﬁ sk-Advance pour attirer l’attention de l’opérateur sur des situations potentiellement dangereuses. Il est donc conseillé de lire attentivement ces indications et de prendre les mesures adéquates en vue de protéger le personnel et le matériel.

DANGER!

Ce symbole est utilisé pour mettre l’opérateur en garde contre les risques immédiats pouvant provoquer des dommages corporels graves, voire entraîner la mort.

ATTENTION!

Ce symbole est utilisé pour attirer l’attention sur une situation susceptible d’entraîner des dommages corporels graves.

PRUDENCE!

Ce symbole est utilisé pour attirer l’attention de l’opérateur sur une situation qui pourrait entraîner des dommages corporels minimes, ou des dommages à la machine ou à d’autres équipements.

Lire toutes les instructions avant d’utiliser l’appareil.

CONSIGNES GENERALES DE SECURITE

Les consignes spéciﬁ ques de prudence et de sécurité mentionnées ici ont pour but de vous informer de la survenance de tout risque de dommages matériels ou corporels.

ATTENTION!

• Cette machine ne pourra être utilisée que par du personnel parfaitement entraîné et dûment autorisé.

• Evitez les arrêts subits lorsque la machine est chargée et se trouve sur des rampes ou des plans inclinés. Evitez les virages serrés. Adoptez une vitesse

réduite lorsque la machine est en descente. Ne nettoyez que lorsque la machine monte la pente.

• Eloignez les batteries de toutes ﬂ ammes, étincelles ou substance fumigène. Les gaz explosifs sont ventilés pendant le fonctionnement normal.

• De plus, du gaz hydrogène explosif s’échappe des batteries lorsqu’elles sont en charge. Ne procédez au chargement des batteries que dans une zone bien

ventilée, loin de toute ﬂ amme. Ne fumez pas à proximité des batteries lorsqu’elles sont en charge.

• Otez tous vos bijoux lorsque vous travaillez à proximité de composants électriques.

• Positionnez la clé de contact sur off (O) et déconnectez les batteries avant de procéder à l’entretien des composants électriques.

• Ne travaillez jamais sous une machine sans y avoir placé, au préalable, des blocs de sécurité ou des étais destinés à soutenir la machine

• Ne déversez pas d’agents nettoyants inﬂ ammables, ne faites pas fonctionner la machine à proximité de ces agents ou d’autres liquides inﬂ ammables.

• Ne nettoyez pas cette machine avec un nettoyeur à pression.

• Ne faites pas fonctionner la machine sur des rampes ou pentes de plus de 2 pour cent.

• Utilisez uniquement les brosses fournies avec l’appareil ou celles spéciﬁ ées dans le manuel d’instructions. L’utilisation d’autres brosses peut mettre la sécurité

en péril.

PRUDENCE!

• Cette machine n’est pas conçue pour une utilisation sur les chemins ou voies publiques.

• Cette machine n’est pas conçue pour le ramassage des poussières dangereuses.

• Lors de l’utilisation de cette machine, assurez-vous que des tiers, et notamment des enfants, ne courent pas le moindre risque.

• Avant de procéder à toute opération d’entretien, veuillez lire attentivement toutes les instructions qui s’y rapportent.

• Ne laissez pas la machine sans surveillance sans avoir, au préalable, coupé le contact, enlevé la clé de contact (O) et tiré le frein à main.

• Positionnez la clé de contact sur off (O) avant de remplacer les brosses ou d’ouvrir tout panneau d’accès.

• Prenez toutes les mesures nécessaires pour éviter que les cheveux, les bijoux ou les vêtements amples ne soient entraînés dans les parties mobiles de la

machine.

• Faites attention lorsque vous déplacez cette machine dans un endroit où la température peut descendre sous 0°. L’eau contenue dans les réservoirs de

détergent, de récupération ou de solution ou dans les conduites risquerait de geler et par là même d’endommager les valves et raccords de la machine. Rincez avec un liquide de lave-glace.

• Prenez soin d’enlever les batteries de la machine avant de mettre cette dernière au rebut. Pour ce qui est de l’élimination des batteries, conformez-vous aux

réglementations locales en matière d’environnement.

• N’utilisez pas sur des surfaces dont la pente dépasse celle mentionnée sur la machine.

• Toutes les portes et couvercles doivent être dans la position mentionnée dans le manuel d’instruction avant de mettre la machine en service.

• Consultez le manuel du fabricant du chargeur de batterie pour plus de consignes de sécurité spéciﬁ ques sur le chargeur de batterie.

CONSERVEZ SOIGNEUSEMENT CES INSTRUCTIONS

A-6 - 56041711 - Adphibian™ / AX 651 Combi EDS

ENGLISH / A-7

KNOW YOUR MACHINE

As you read this manual, you will occasionally run across a bold number or letter in parentheses - example: (2). These callouts refer to an item shown on the next 4 pages unless otherwise noted. Refer back to these pages whenever necessary to pinpoint the location of an item mentioned in the text. NOTE: Refer to the service manual for detailed explanations of each item illustrated on the next 4 pages.

1 Solution Fill Cap 2 Bottle Holders 3 Recovery Tank Dome Lid 4 Recovery Tank 5 Detergent (AXP/EDS) Cartridge Access Cover 6 Detergent (AXP/EDS) Cartridge 7 Scrub Deck Rollers 8 Scrub Deck 9 Idler Assembly

10 Extraction Shoes 11 Drive Wheel 12 Vacuum Motor Inlet Screens 13 Solution Tank 14 Onboard Battery Charger 15 LIFT Low Moisture Spray Nozzle 16 Restoration Spray Nozzle 17 Battery Pack Connector 18 Squeegee Assembly

Adphibian™ / AX 651 Combi EDS - 56041711 - A-7

A-8 / ENGLISH

KNOW YOUR MACHINE

19 Operator Control Handle 20 Drive Paddle 21 Speed Control Knob 22 Solution Drain Hose / Level Indicator 23 10 Amp-Control Circuit Circuit Breaker 24 30 Amp-Drive Motor Circuit Breaker 25 Recovery Tank Drain Hose 26 Rear Caster 27 Accessory Port 28 Solution Filter 29 Debris Hopper 30A Vacuum Recovery Hose (Extract position) 30B Vacuum Recovery Hose (Scrub position)

31 Solution Shut-Off Valve 32 Recovery Drain Hose Cap 33 Control Panel 34 Vacuum Shut Off Switch 35 Squeegee Adjustment Knob 36 Squeegee Raise Lower/Lever 37 Squeegee Blade Latch 38 Squeegee Blade Tension Strap 39 Squeegee Blade Alignment Pins 40 Squeegee Mount Thumb Nut

A-8 - 56041711 - Adphibian™ / AX 651 Combi EDS

CONTROL PANEL - 1

ENGLISH / A-9

A Key Switch B Detergent System C Solution/ Pre-Spray Switch D Display Panel D1 AXP/EDS Indicator D2 Hourmeter/Battery Indicator D3 Fault Indicator D4 AXP/EDS Detergent Ratio Indicator D5 LIFT Low Moisture Extract Mode Indicator D6 Restoration Extract Mode Indicator D7 Fast Prespray Mode

Extract Mode

D11

D8 Heavy Prespray Mode D9 Recovery Tank Full Indicator D10 Battery Low Indicator D11 Extract Mode Indicator E Vacuum Switch F Speed Control Fault Code Indicator G Wand Switch H Scrub OFF Switch (Red) J Scrub ON Switch (Green) K Floor Mode Switch (Orange)

EXTRACT

D10

Adphibian™ / AX 651 Combi EDS - 56041711 - A-9

A-10 / ENGLISH

CONTROL PANEL - 2

A Key Switch B Detergent System C Solution/ Pre-Spray Switch D Display Panel D1 AXP/EDS Indicator D2 Hourmeter/Battery Indicator D3 Fault Indicator D4 AXP/EDS Detergent Ratio Indicator D9 Recovery Tank Full Indicator D10 Battery Low Indicator D12 Scrub Mode Indicator

Scrub Mode

D12

SCRUB

D13 Solution OFF Indicator D14 Light Scrub Pressure Indicator D15 Solution Active Indicator D16 Heavy Scrub Pressure Indicator E Vacuum Switch F Speed Control Fault Code Indicator G Wand Switch H Scrub OFF Switch (Red) J Scrub ON Switch (Green) K Floor Mode Switch (Orange)

D10

D13

D14

D15

D16

A-10 - 56041711 - Adphibian™ / AX 651 Combi EDS

ENGLISH / A-11

BATTERIES

If your machine shipped with batteries installed do the following:

• Check that the batteries are connected to the machine (17).

• Turn ON the Key Switch (A) and check the Battery Indicator (D2). If the gauge is completely ﬁ lled, the batteries are ready for use. If the

gauge is less than full, the batteries should be charged before use. See the “Charging The Batteries” section.

• IMPORTANT!: YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER, REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE (SEE CHART).

If your machine shipped without batteries installed do the following:

• Consult your Authorized Nilﬁ sk-Advance dealer for recommended batteries.

• Install the batteries by following the instructions below.

• DO NOT install two 12 volt batteries in your machine. This affects the stability of the machine.

• IMPORTANT!: YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER, REFER TO THE OEM PRODUCT MANUAL FOR INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE (SEE CHART).

AH/Rate MFG Algorithm

255 Discover 43 251 US 72 180 DEKA(gel) 6

201 / 195 US / Trojan 11 / 3

235 US / Trojan 11 / 3

WARNING!

Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or eyes. Explosive hydrogen gas is vented from the batteries through openings in the battery caps. This gas can be ignited by any electrical arc, spark or ﬂ ame. Do not install any lead-acid battery in a sealed container or enclosure. Hydrogen gas from overcharging must be allowed to escape.

When Servicing Batteries...

• Remove all jewelry

• Do not smoke

• Wear safety glasses, rubber gloves and a rubber apron

• Work in a well-ventilated area

• Do not allow tools to touch more than one battery terminal at a time

• ALWAYS disconnect the negative (ground) cable ﬁ rst when replacing batteries to

prevent sparks.

• ALWAYS connect the negative cable last when installing batteries.

FIGURE 1

CAUTION!

Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly. Nilﬁ sk-Advance, a qualiﬁ ed electrician, or the battery manufacturer should install batteries.

1 Remove the batteries from their shipping crate and carefully inspect them for cracks or other damage. If damage is evident, contact the carrier

that delivered them or the battery manufacturer to ﬁ le a damage claim.

2 Turn the Master Key Switch (A) OFF and remove the key. 3 Tip the recovery tank to the side, locked position. Remove the battery cables from inside the battery compartment. 4 Your machine comes from the factory with enough battery cables to install four 6 volt batteries. Carefully lift the batteries into the battery

compartment and arrange them exactly as shown in FIGURE 1. Secure the batteries as close to the back of the machine as possible.

5 Install the battery cables as shown. Position the cables so the battery caps can be easily removed for battery service. 6 Carefully tighten the nut in each battery terminal until the terminal will not turn. Do not over-tighten the terminals, or they will be very difﬁ cult to

remove for future service.

7 Coat the terminals with spray-on battery terminal coating (available at most auto parts stores). 8 Put one of the black rubber boots over each of the terminals and connect the Battery Pack Connector (17).

Adphibian™ / AX 651 Combi EDS - 56041711 - A-11

A-12 / ENGLISH

INSTALLING THE BRUSHES

CAUTION!

Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels.

1 Make sure the Brush Deck is in the RAISED position. Make sure the Key Switch (A) is off (O). 2 See Figure 2. To access the brushes loosen the black knobs (one on each side) on top of the Idler Assemblies (9) and remove the idler

assemblies. Slide the brush into the housing, lift slightly, push and turn until it seats. Re-install the idler assemblies.

FIGURE 2

FILLING THE SOLUTION TANK

Fill the solution tank with a maximum of 20 gallons (76 Liters) of cleaning solution. Do not ﬁ ll the solution tank above 7.5 cm (3 inches) from the bottom of the Solution Fill (1). Use the Solution Level Indicator (22) to monitor the solution level while ﬁ lling. The solution should be a mixture of water and the proper cleaning chemical for the job. Always follow the dilution instructions on the chemical container label. NOTE: Machines can either be used conventionally with detergent mixed in the solution tank or the AXP/EDS detergent dispensing system can be used. When using the AXP/EDS detergent dispensing do not mix detergent in the tank, plain water should be used.

CAUTION!

Use low-sudsing, non-ﬂ ammable liquid detergents designed for machine application. Water temperature should not exceed 130 degrees Fahrenheit (54.4 degrees Celsius).

A-12 - 56041711 - Adphibian™ / AX 651 Combi EDS

ENGLISH / A-13

BEFORE USING THE ADPHIBIAN™ / AX 651 COMBI EDS FOR EXTRACTING

Thoroughly vacuum the carpet to be cleaned before using the Adphibian/AX 651 Combi EDS automatic carpet extractor.

PRE-SPRAYING THE CARPET

The Adphibian/AX 651 Combi EDS in extract mode has a pre-spray feature. Pre-spray spots and heavy trafﬁ c areas before extracting. For extremely dirty ﬂ oors, a one-pass scrubbing operation may not be satisfactory and a “pre-spray” operation may be required. This operation is the same as a one-pass scrubbing except on the ﬁ rst pass the vacuum shoes are in the up position and the vacuum motors are off. This allows the cleaning solution/detergent to remain on the ﬂ oor to work longer. The ﬁ nal pass is made over the same area, with the vacuum shoes lowered and vacuum motors on to pick up the accumulated solution.

1 The scrub system must be in the off position. 2 Press the orange Floor Mode Switch (K) until the display shows (D11) indicating Extract Mode has been selected. 3 Press the Solution/Pre-Spray Switch (C), the Display (D7) will indicate Fast Prespray Mode. The scrub deck will be lowered and the solution

and detergent systems will be enabled. The Extraction Shoes (10) will remain in the up position.

4 Push the Drive Paddle (20) forward to start the brushes and solution/detergent. 5 Press the Solution/Pre-Spray Switch (C) to exit the prespray mode. The brushes and solution/detergent ﬂ ow will be stopped. The scrub deck

will raise.

6 If more solution is desired, press the green Scrub ON Switch (J) (while in Fast Prespray Mode) to enter the Heavy Prespray Mode. The Display

(D8) will indicate the Heavy Prespray Mode has been selected. In this mode the machine moves slower and more solution is sprayed on the carpet.

PLAN FOR CLEANING

Before you begin extracting, look at the area to be cleaned and plan your work. Divide the space into sections. Overlap each pass 2 inches (5 cm).

SQUEEGEE INSTALLATION

1 See Figure 3. Slide the Squeegee Assembly (18) onto the squeegee mount bracket and tighten the Squeegee Mount Thumb Nuts (40). 2 Connect the Recovery Hose (30) to the squeegee inlet. 3 Lower the squeegee, move the machine ahead slightly and adjust the squeegee tilt using the Squeegee Adjustment Knob (35) so that the rear

squeegee blade touches the ﬂ oor evenly across its entire width and is bent over slightly as shown.

FIGURE 3

Adphibian™ / AX 651 Combi EDS - 56041711 - A-13

A-14 / ENGLISH

DETERGENT (AXP/EDS) SYSTEM PREPARATION AND USE

COMMON INSTRUCTIONS:

Pressing and releasing the Detergent Switch (B) while the solution system is active will cause the detergent system to alternately turn on and off. The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over ﬂ oor drain before purging because a small amount of detergent will be dispensed in the process.

To Purge When Changing Chemicals:

1 Disconnect and remove the detergent cartridge. 2 Turn the Key Switch (A) ON and press the Detergent Switch (B) and

the Solution/Pre-Spray Switch (C) down for at least 2 seconds. NOTE: Once activated the purge process takes 30 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.

To Purge Weekly:

1 Disconnect and remove the detergent cartridge. Install and connect a

Cartridge ﬁ lled with clean water

2 Turn the Key Switch (A) ON and press the Detergent Switch (B) and

When the Detergent Cartridge is almost empty a Display Panel (D1) indicator will come on. This “Low Detergent” indicator will remain on until you reset the system. Once this indicator comes on you should be able to simply pour an entire gallon bottle of detergent into the Cartridge to reﬁ ll without worrying about measuring. NOTE: Only reset the system when the cartridge is full. When switching cartridges, the “Low Detergent” indicator is only accurate if the replacement cartridge is at the same level as the cartridge being replaced.

To Reset:

1 Turn the Key Switch (A) ON and hold the Detergent Switch (B)

down for 2 seconds. See illustration on next page for Detergent System indicators.

NON-REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Remove the Cap (AA) and place the cartridge in the detergent box. Install the Dry Break Cap (BB) as shown.

REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS:

Fill the detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to ﬁ lling to avoid spilling detergent on the machine. It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The detergent cartridge has a Magnetic Slider (CC) on one end that needs to be set to the proper dilution ratio according to the dilution instructions on the manufacturer’s bottle. Slide the Magnet Slider (CC) to the appropriate location on Detergent Dilution Ratio Decal (DD). When installing a new cartridge, remove the Cap (AA) and place the cartridge in the detergent box. Install the Dry Break Cap (BB) as shown.

A-14 - 56041711 - Adphibian™ / AX 651 Combi EDS

DETERGENT (AXP/EDS) SYSTEM PREPARATION AND USE

ENGLISH / A-15

DETERGENT ON

FULL (RESET)

DETERGENT LOW

DETERGENT OFF

PURGE

Press (B) & (C) for 2 seconds to purge.

Press (B) for 2 seconds to reset.

Adphibian™ / AX 651 Combi EDS - 56041711 - A-15

+ 33 hidden pages