Page 1
I N S T A L L A T I O N G U I D E
PHD60 PHD42 PHD30
F O R U S E W I T H P L A S M A O R O T H E R F L A T - P A N E L D I S P L A Y
M U LT I -WAY, H I GH- D E FIN I T IO N , WAL L - M OU N T LO U D SPE A K ER S
Page 2
Thank you for choosing the PHD60/42/30 High-Definition, Left/Center/Right Channel,
Loudspeaker from Niles. With proper installation and operation, you should enjoy years of
trouble-free use.
Niles manufactures the industry’s most complete line of custom installation components and
accessories for audio/video systems. To see the complete Niles product assortment, visit us on
the Internet at: www.nilesaudio.com
TABLE OF CONTENTS
Introduction 1
Features and Benefits 2
Installation Considerations 4
Loudspeaker Placement 5
Installing the Wall-Mount Brackets 7
Finishing the Installation 9
Operation 13
Specifications 14
Notes 15
Limited Warranty 16
Warranty Registration Card 17
CONGRATULATIONS!
Page 3
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
INTRODUCTION
The Niles PHD60/42/30 High-Definition, Left/Center/Right Channel, Loudspeaker is expressly
designed for superior sonic quality in front left-, center-, or front right-channel applications. It
employs advanced technology components that extract the subtle nuances in recorded music or
the thunderous action sound in a movie. The PHD60/42/30 is the perfect choice wherever quality
of sound is the most important consideration.
1
PHD60 PHD42 PHD30
Page 4
2
FEATURES AND BENEFITS
THREE MODELS DESIGNED FOR USE WITH PLASMA OR
OTHER FLAT-PANEL DISPLAYS
The largest model, the PHD60, is designed for use with plasma or other flat-panel displays of
60-inches or more. The PHD42 complements 42-inch and over displays, while the PHD30 works
with 30-inches or larger displays. Except for differences in the transducer complement and
performance, all three models feature similar technologies, For example: the PHD60 and 42 feature
a 3-way loudspeaker design, while the PHD30 features a 2-way design. All offer voice matching
sound quality and exceptional detail over a wide listening area.
5-1/4-INCH TCC WOOFERS WITH CONE-FORWARD™
DESIGN AND BUTYL-RUBBER SUSPENSION
The PHD60/42/30 features newly-developed woofer-cone material that combines injection-molded
polypropylene with talc, carbon, and ceramic (TCC) stiffening agents. As a result, the cone offers
extreme stiffness and light weight for accurate, dynamic response. Our patent-pending Cone
Forward™ design positions the woofer cone at the front of the baffle for natural-sounding bass
and clear, open midrange response. Additionally, the use of a butyl-rubber suspension offers
substantial benefits, including increased movement without mechanical limitations, and improved
midrange damping for better detail and clarity.
1-1/2-INCH FLUID-COOLED TETERON HYPERBOLICDOME MIDRANGE DRIVER
The PHD60 and PHD42 also feature a Fluid-Cooled Teteron Hyperbolic-Dome Midrange Driver that
provides high sound pressures to reproduce critical mid frequencies with exceptional accuracy.
1-INCH FLUID-COOLED TETERON TRI-LAMINATE TWEETER
The PHD60/42/30’s Fluid-Cooled Teteron Tweeter employs a tri-laminate design consisting of
an inner textile layer, which forms the dome, a high damping layer to eliminate unwanted
resonances, and an outside layer of urethane to add stiffness and prevent breakup modes. The
result is a transparently clear, sweet, natural-sounding tweeter, which still maintains extended
frequency response.
Page 5
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
3
ADJUSTABLE, DISPERSION-CONTROLLING MIDRANGE/
TWEETER POD ENABLES PRECISE IMAGING
The PHD60 and PDH42 each feature a unique Midrange/Tweeter pod that can be rotated and
pivoted to enable precise imaging regardless of placement. The pod accommodates vertical or
horizontal installations and can be set by the installer after each loudspeaker is mounted. Included
are variable treble and midrange level controls for additional response contouring.
NILES’ HD HIGH-DEFINITION VOICE MATCHING
Ensures compatibility with other Niles HD High-Definition in-wall, on-wall, and ceiling-mount
models to accommodate a wide range of system designs.
ADVANCED BASS-REFLEX DESIGN FOR ENHANCED
DYNAMIC IMPACT
The PHD60/42/30’s bass-reflex design enhances low-frequency response and dynamic impact.
Moreover, the rigid extruded aluminum enclosure helps deliver accurate bass response with
low distortion.
LOOKS GREAT AND EASY TO INSTALL
The PHD60/42/30’s contemporary finish matches popular flat-panel displays, and its integrated
wall mount brackets make installation quick and easy.
DOLBY® DIGITAL READY
The PHD60/42/30 is specifically designed for Home Theater Sound. They are designed to
complement and provide for the accurate reproduction of Dolby Digital Encoded Sources.
Page 6
TECH TIP
Wire size is expressed by its AWG (American
Wire Gauge) number – the lower the number,
the larger the wire. For example, 12 AWG is
physically larger than 14 AWG.
INSTALLATION CONSIDERATIONS
WALL MOUNTING
The Niles PHD60/42/30 loudspeaker is equipped with an included wall-mount bracket for quick
and easy installation on a wall. Ideally, a PHD60/42/30 should be placed so that its bracket can
be installed on underlying wall studs. If stud mounting is impractical, dry-wall anchors (rated for
at least 40 pounds) can be used to mount the loudspeaker between studs (see INSTALLING THE
WALL-MOUNT BRACKETS on page 7).
RECOMMENDED AMPLIFIER POWER
For satisfactory performance, we recommend using a home theater receiver (or amplifier) with
a power rating of 10 to 250 watts for the PHD60,10 to 200 watts for the PHD42, and 10 to 150
watts for the PHD30. Most loudspeakers are not damaged by large amplifiers, but rather by small
amplifiers. If your system is playing loud music, a small amplifier will run out of power very quickly
and can create damaging “clipping” distortions. A more powerful amplifier will play at the same
volume without distorting. See OPERATION on page 13 for more information about amplifier
clipping distortion.
LOUDSPEAKER WIRE
Use 2-conductor loudspeaker wire when connecting loudspeakers to your receiver or amplifier.
For most applications, we recommend using 16- or 18-gauge wire. For wiring runs longer than
80 feet, we recommend 14-gauge wire. The spring-loaded terminals of the PHD60/42/30 will
accommodate up to 12-gauge wire directly. Larger sizes can be accommodated via
pin connectors.
When running wire inside walls or ceilings, always use (CL-2 or CL-3) rated cable. In some areas,
conduit is also required. For a trouble-free installation, low-voltage wire such as loudspeaker wire
must be run in accordance with the National Electrical Code and any applicable provisions of the
local building code. If you are unsure of the correct installation techniques, wire jacket, or type of
conduit to use, consult a professional audio/video installer, building contractor, or the local building
and inspection department.
4
Page 7
Figure 1.
Recommended PHD60
loudspeaker placement
for front left and right
channels is shown
here. Placement of the
PHD42/30 is similar.
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
5
(CONTINUED ON NEXT PAGE)
LOUDSPEAKER PLACEMENT
The Niles PHD60/42/30 loudspeaker is designed for use in front left-, center-, or front rightchannel applications. Any model can be wall-mounted using its included wall-mount bracket.
For rear-channel applications, we recommend using a Niles HD FX or CM6HDfx loudspeaker.
PLACING PHD60/42/30’S AS THE FRONT LEFT AND
RIGHT LOUDSPEAKERS
In a home theater, the intelligibility of dialog and action reproduced by the front speakers is
paramount! The position of the loudspeakers plays a very important role in how clear the sound is
and how a stereo image is created.
The PHD60/42/30’s are designed specifically for use with plasma or flat-panel displays in a home
theater system. The placement process is quick and easy:
• At the proposed site, make sure the sound will not be blocked or reflected off furniture
or other objects. The listener should have a direct line of sight with the front of each
loudspeaker. The ideal listening position (e.g., favorite chair or couch) should be
centered with the middle of plasma or flat-panel display
• Place the speakers with the ports on the bottom on either side of display, as shown
in Figure 1 (also see INSTALLING THE WALL-MOUNT BRACKETS on page 7). In
applications where there is a center channel, you may choose to space the left and
right main speakers farther apart for a “bigger than life” sound with Dolby
®
encoded
movies and TV shows.
Aim midrange and
tweeter towards
listener
Critical
Listening
Position
Aim midrange and
tweeter towards
listener
Plasma TV
Page 8
Figure 2.
Recommended PHD60
loudspeaker placement
for the center channel is
shown here. Placement of
the PHD42/30 is similar.
Figure 3. Recommended PHD60 center-channel
placement with grille removed behind a perforated
projection screen is shown here. Placement of the
PHD42/30 is similar.
PLACING PHD60/42/30’S AS THE FRONT LEFT AND RIGHT
LOUDSPEAKERS
(CONTINUED)
• As for placement height, place front left and right speakers vertically on either side
of the display, so that their tweeters are not more than 24 inches above or below the
center-channel loudspeaker’s tweeter (see Figure 2 below).
PLACING A PHD60/42/30 AS THE CENTER-CHANNEL
LOUDSPEAKER
The center-channel loudspeaker is the workhorse in a home theater system. It handles all of the
critical dialog and is vitally important in creating the illusion of sounds emanating directly from the
picture. Here are some tips for obtaining optimum center-channel performance:
• In a typical installation, place the PHD60/42/30 horizontally, directly above or below the
plasma or flat-panel display. Make sure the loudspeaker is not placed too high or low
relative to the left and right speakers, as shown in Figure 2
.
• For installations where a perforated projection
screen will be used, place the PHD60/42/30
with grille removed, either horizontally or
vertically, behind the screen at ear level,
as shown in
Figure 3.
6
Not Greater
than 24"
Not Greater
than 24"
Perforated Screen
Page 9
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
7
(CONTINUED ON NEXT PAGE)
INSTALLING THE WALL-MOUNT BRACKETS
TOOLS AND PARTS
We recommend using the following tools and parts to install the PHD60/42/30 wall-mount brackets:
• Electric drill and drill bits
• Philips screwdrivers or driver bit set
• Stud finder
• Eight wood screws with (optional) dry-wall anchors rated for at least 40 pounds
• Pencil
• Level
• Protective eyewear
PRECAUTIONS
Before starting the installation, please observe the following precautions:
• Turn off all system power before making any connections.
• Always wear protective eyewear when using tools.
• Make sure hands are clean before installation.
• Wear gloves when working with fiberglass insulation.
INSTALLATION
1. At each proposed site, use a stud finder to locate studs (which should be on 16-inch
centers) for possible use in the installation. If the studs do not line up with a desired
placement location, the PHD60/42/30 wall-mount bracket can still be mounted on a dry
wall with appropriate dry-wall screws and anchors.
IMPORTANT: DO NOT USE PLASTIC EXPANSION OR THREADED WALL ANCHORS FOR DRY
WALL INSTALLATION. CONSULT YOUR LOCAL NILES DEALER OR HOME HARDWARE STORE
FOR RECOMMENDATIONS FOR YOUR HOME THEATER APPLICATION.
Page 10
Figure 4. The PHD mounting template is shown in
horizontal and vertical positions (with TOP side up).
INSTALLATION (CONTINUED)
2. For each loudspeaker, orient and tape the enclosed mounting template to the wall
at the desired placement location, as shown in Figure 4. Use a level to verify tilt
is zero. Be sure to account for any moldings that may interfere with the loudspeaker
cabinet upon installation.
3. Follow the directions included on the template. Drill four small mounting holes at the
designated locations noted on the template. If you also plan to run loudspeaker wire
in the wall, you’ll need to create a cutout for it within the noted wire boundary (see
Figure 4). When drilling is complete, remove each mounting template.
4. Use the stamped (TOP) label to orient each mounting bracket and run loudspeaker
wire through its opening for later connection. Fasten each bracket to the wall with
appropriate mounting hardware.
8
Bracket Template
Page 11
Figure 5. Connecting
a loudspeaker wire to the
PHD60/42/30 terminals.
Figure 6. Installing a PHD60/42/30 loudspeaker
onto its mounting bracket.
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
9
FINISHING THE INSTALLATION
CONNECTING THE LOUDSPEAKER
1. At each loudspeaker, separate the loudspeaker wire so that at least 2 inches of each
conductor are free. Strip away 1/4 inch of insulation from each loudspeaker wire.
2. On each set of loudspeaker connectors, press down the spring-loaded lever, insert the
appropriate conductor, and then release the lever, as shown in Figure 5. Gently tug
on the loudspeaker wire to make sure it is held in place. If not, repeat this procedure
until it is. Make sure that only the bare wire is clamped in the connector.
NOTE: OBSERVE CORRECT POLARITY: POSITIVE (+) GOES INTO THE RED TERMINAL AND
NEGATIVE (–) GOES INTO THE BLACK TERMINAL. IF YOU ARE UNSURE OF WIRE POLARITY, SEE
THE SECTION CHECKING LOUDSPEAKER PHASE ON PAGE 11.
3. If a mounting bracket was installed
on the wall, align each loudspeaker
with the two mounting holes (on its
bracket) and let it slide down into the
keyslot on the bracket to fasten it to
the wall, as shown in
Figure 6.
(CONTINUED ON NEXT PAGE)
Page 12
Figure 7. Each PHD60/42 includes an adjustable Tweeter/Midrange Pod that can be rotated up
to 90 degrees for proper loudspeaker orientation and pivoted for precise imaging.
CONNECTING THE LOUDSPEAKER (CONTINUED)
4. Connect the other end of the loudspeaker wires to the home theater receiver (or
amplifier) in the same way as steps 1 and 2.
5. Turn on the home theater receiver and calibrate all loudspeakers in the system
according to the receiver manufacturer’s instructions.
PHD60/42: SETTING THE TWEETER/MIDRANGE POD
Each PHD60/42 features an adjustable Tweeter/Midrange Pod on the front baffle for proper
loudspeaker orientation and precise imaging, as shown in Figure 7. Adjust the pod as follows:
• For a vertical installation, no adjustments are required. The Tweeter/Midrage pod is
optimally set at the factory for this placement.
• For a horizontal installation (e.g., center-channel application), perform the following
steps to rotate the Tweeter/Midrage pod:
1. Using the enclosed Allen wrench, remove the four (4) Allen-head screws,
(see Figure 7).
2. Gently pull the pod away from the enclosure and rotate it 90° in either direction (see
Figure 7). Be careful not to disconnect any attached wires during rotation.
3. Place the pod back into the enclosure and reinstall the four (4) Allen-head screws.
• If desired, after vertical or horizontal installation, set the imaging by pressing the pod’s
edge to aim the drivers at the listening position (see Figure 7).
10
Page 13
Figure 8. Each PHD60/42 includes variable
TREBLE and MIDRANGE controls with up to 3 dB of
boost or cut in the response.
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
PHD60/42: ACOUSTIC FINE TUNING
Each PHD60/42 also features variable TREBLE and MIDRANGE controls on the front baffle for
acoustic fine-tuning after placement, as shown in Figure 8. Adjust these controls as follows:
• Initially set both TREBLE and MIDRANGE control to 0 dB.
• If a PHD60/42 is placed in a room with highly reflective surfaces like glass or tile or
the reproduced sound is too bright, decrease the TREBLE setting by as much as –3 dB
to lower the high-frequency response. If the room has heavy drapes or is wallpapered,
try increasing the TREBLE setting by as much as +3 dB to brighten the
high-frequency response.
• Listen to dialog being reproduced on the PHD60/42. If you want it more pronounced,
increase the MIDRANGE setting by as much as +3 dB to enhance the mid-frequency
response. If the dialog is too pronounced, decrease the MIDRANGE setting by as much
as –3 dB to lower the mid-frequency response.
CHECKING LOUDSPEAKER PHASE
Loudspeaker wire has two conductors. On both your loudspeaker and amplifier, one conductor
is attached to the negative (–) terminals, while the other is attached to the positive (+) terminals.
Usually, the wire is marked for your convenience, but the marking can be done in the following
different ways:
• Stripe on one wire
• Ribbed area you can feel on one conductor
• Different colors of metal wire on each conductor
• Fabric strand or string wound into one of the conductors
11
(CONTINUED ON NEXT PAGE)
Page 14
CHECKING LOUDSPEAKER PHASE (CONTINUED)
Of course, there are some wires that appear completely identical. So be careful, or you might make
a connection mistake. If you do, one loudspeaker will be playing “out-of-phase” with the other
loudspeaker. A pair of out-of-phase loudspeakers works against each other, and the sound of the
two playing together will be lacking in bass and sound “phasey.” If you suspect the sound is not
right, and you cannot see any markings on the wire, try this simple test:
1. Stand halfway between the loudspeakers.
2. Play some music with the amplifier or receiver set to Mono.
3. Listen to the richness of the bass and the loudness of the sound.
4. Turn off the amplifier and reverse the connections on one amplifier channel only.
5. Repeat the listening test with the same volume control setting. When the sound has a
richer bass and is slightly louder, the loudspeakers are working together or “in-phase.”
INSTALLING THE GRILLE
If desired, at each loudspeaker, carefully fit the grille to its cabinet. Starting with one corner, gently
press the grille frame around the loudspeaker’s edge, pushing it in at each of the recessed holes.
12
Page 15
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
OPERATION
LISTENING AT HIGHER VOLUMES
Achieving a reasonable volume of sound in a large room requires more amplifier power than it
does in a small room. It is possible to turn the volume up so high that the amplifier runs out of
power. This creates “clipping” distortion, which will make treble sound very harsh and unmusical.
When you hear harsh-sounding treble from any good loudspeaker, turn the volume down
immediately! Those harsh sounds are masking much more powerful ultra-high-frequency sound
spikes, which will quickly damage any fine loudspeaker. You are much less likely to damage a
loudspeaker driven by a large amplifier because it will be very loud before any clipping
distortion is produced.
CLEANING
To clean the enclosure, use a dampened soft cloth or paper towel. To clean the grille, use a gentle
vacuum cleaner.
13
Page 16
14
SPECIFICATIONS
PHD60
Driver Complement
• Four 5-1/4" TCC Woofers
• 1-1/2" Teteron Midrange
with fluid cooling
• 1" Teteron Tweeter with
fluid cooling
Design Principle
• Bass-reflex design
• 3-way crossover for
optimum phase and
frequency response
• Adjustable, dispersioncontrolling, midrange/
tweeter pod
Recommended Amplifier
Power
10 to 250 watts per channel
Nominal Impedance
4 ohms
Frequency Response
55 Hz to 21 kHz, +/- 3 dB
Sensitivity
90 dB with 2.83 V pink noise
input, measured at 1 meter
on axis
Dimensions (with Wall
Bracket)
34.7" H x 6.2" W x 5.6" D
Weight
40 lb
Wiring Requirements
We recommend using 16- to
18-gauge loudspeaker wire
for runs up to 80 feet and
14-gauge loudspeaker wire
for runs up to 200 feet. The
connectors will accommodate
12- to 22-gauge wire.
PHD42
Driver Complement
• Four 5-1/4" TCC Woofers
• 1-1/2" Teteron Midrange
with fluid cooling
• 1" Teteron Tweeter with
fluid cooling
Design Principle
• Bass-reflex design
• 3-way crossover for
optimum phase and
frequency response
• Adjustable, dispersioncontrolling, midrange/
tweeter pod
Recommended Amplifier
Power
10 to 200 watts per channel
Nominal Impedance
4 ohms
Frequency Response
63 Hz to 21 kHz, +/- 3 dB
Sensitivity
89 dB with 2.83 V pink noise
input, measured at 1 meter
on axis
Dimensions (with Wall
Bracket)
24.8" H x 6.2" W x 5.6" D
Weight
30 lb
Wiring Requirements
We recommend using 16- to
18-gauge loudspeaker wire
for runs up to 80 feet and
14-gauge loudspeaker wire
for runs up to 200 feet. The
connectors will accommodate
12- to 22-gauge wire.
PHD30
Driver Complement
• Two 5-1/4" TCC Woofers
• 1" Teteron Tweeter with
fluid cooling
Design Principle
• Bass-reflex design
• 2-way crossover for
optimum phase and
frequency response
• Symmetrical driver
configuration for dispersion
control and precise imaging
Recommended Amplifier
Power
10 to 150 watts per channel
Nominal Impedance
4 ohms
Frequency Response
70 Hz to 21 kHz, +/- 3 dB
Sensitivity
89 dB with 2.83 V pink noise
input, measured at 1 meter
on axis
Dimensions (with Wall
Bracket)
19.6" H x 6.2" W x 5.6" D
Weight
20 lb
Wiring Requirements
We recommend using 16- to
18-gauge loudspeaker wire
for runs up to 80 feet and
14-gauge loudspeaker wire
for runs up to 200 feet. The
connectors will accommodate
12- to 22-gauge wire.
Page 17
NILES AUDIO CORPORATION – 1-800-BUY-HIFI
NOTES
15
Page 18
16
LIMITED WARRANTY
NILES AUDIO CORPORATION (“NILES”) WARRANTS ITS LOUDSPEAKER PRODUCTS TO THE ORIGINAL PURCHASER TO
BE FREE OF MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP FOR A PERIOD OF TWO YEARS FROM
DATE OF PURCHASE.
THIS WARRANTY IS SUBJECT TO THE FOLLOWING ADDITIONAL CONDITIONS AND LIMITATIONS. THE WARRANTY
IS VOID AND INAPPLICABLE IF NILES DEEMS THAT THE PRODUCT HAS BEEN USED OR HANDLED OTHER THAN IN
ACCORDANCE WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER, INCLUDING BUT NOT LIMITED TO
DAMAGE CAUSED BY ACCIDENT, MISHANDLING, IMPROPER INSTALLATION, ABUSE, NEGLIGENCE, OR NORMAL
WEAR AND TEAR, OR ANY DEFECT CAUSED BY REPAIR TO THE PRODUCT BY ANYONE OTHER THAN NILES OR AN
AUTHORIZED NILES DEALER.
TO OBTAIN WARRANTY SERVICE, TAKE THE UNIT TO THE NEAREST AUTHORIZED NILES DEALER, WHO WILL
TEST THE PRODUCT AND IF NECESSARY, FORWARD IT TO NILES FOR SERVICE. IF THERE ARE NO AUTHORIZED
NILES DEALERS IN YOUR AREA, YOU MUST WRITE TO NILES AND INCLUDE YOUR NAME, ADDRESS, MODEL AND
SERIAL NUMBER OF YOUR UNIT, ALONG WITH A BRIEF DESCRIPTION OF THE PROBLEM. A FACTORY RETURN
AUTHORIZATION NUMBER WILL BE SENT TO YOU. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING WRITTEN
AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM NILES.
IF THE ABOVE CONDITIONS ARE MET, THE PURCHASER’S SOLE REMEDY SHALL BE TO RETURN THE PRODUCT TO
NILES, IN WHICH CASE NILES WILL REPAIR OR REPLACE, AT ITS SOLE OPTION, THE DEFECTIVE PRODUCT WITHOUT
CHARGE FOR PARTS OR LABOR. NILES WILL RETURN A UNIT REPAIRED OR REPLACED UNDER WARRANTY BY
SHIPPING SAME BY ITS USUAL SHIPPING METHOD FROM THE FACTORY (ONLY) AT ITS EXPENSE WITHIN THE
UNITED STATES OF AMERICA. THERE ARE NO OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION, EITHER
EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH
RESPECT TO THE PRODUCT.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER/
PURCHASER. NILES SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO
THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
FOR THE NAME OF YOUR NEAREST AUTHORIZED NILES DEALER CONTACT:
NILES AUDIO CORPORATION, P.O. BOX 160818, MIAMI, FLORIDA 33116-0818.
Please fill in your product information and retain for your records.
Model______________________ Serial No.___________________ Purchase Date_______
DETACH HERE AND RETURN TO: NILES AUDIO CORPORATION WARRANTY REGISTRATION DEPT. P.O. BOX 160818 MIAMI, FLORIDA 33116-0818
Page 19
Model Purchased _________________________________________________________
Serial Number ___________________________________________________________
Date Purchased (month/day/year) _____________________________________________
Dealer Name and Location __________________________________________________
______________________________________________________________________
❍
Dr.
❍
Miss
❍
Mr.
❍
Mrs.
❍
Ms.
Name__________________________________________________________________
Address________________________________________________________________
______________________________________________________________________
City_______________________________________State________________Zip ______
Telephone ( ) _________________________________________________
Please take a moment to fill out our warranty registration card. The information helps us to get to
know you better and develop the products you want
DETACH HERE AND RETURN TO: NILES AUDIO CORPORATION WARRANTY REGISTRATION DEPT. P.O. BOX 160818 MIAMI, FLORIDA 33116-0818
Age:
❍
Under 25
❍
25-34
❍
35-44
❍
45-54
❍
55 & over
Income:
❍
Under $24,999
❍
$25,000-$34,999
❍
$35,000-$44,999
❍
$45,000-$59,999
❍
$60,000-$74,999
❍
$75,000-$99,999
❍
Over $99,999
Occupation:
❍
Arts/Entertainment
❍
Business Owner
❍
Engineer
❍
Finance/Accounting
❍
General Office
❍
Management
❍
Professional
❍
Sales/Marketing
❍
Student
❍
Tradesperson
Musical tastes:
(Please check
all that apply)
❍
Alternative
❍
Classical
❍
Country
❍
Jazz
❍
New Age
❍
Popular
❍
R&B
❍
Rock
❍
Other _____________
How did you hear
about Niles?
❍
Architect/Developer
❍
Custom Installer
❍
Direct Mail
❍
Friend/Family
❍
In-Store Display
❍
Interior Designer
❍
Magazine Ad
❍
Mail-Order Catalog
❍
Newspaper Ad
❍
Product Brochure
❍
Product Review
❍
Retail Salesperson
What magazines
do you read?
1. ________________
2. ________________
3. ________________
Who will install
the product?
❍
Custom Installer
❍
Electrician
❍
Friend
❍
Myself
Which factor(s) influenced
the purchase of your Niles
product? (Please check
all that apply)
❍
Ease of Use
❍
Price/Value
❍
Product Features
❍
Quality/Durability
❍
Reputation
❍
Style/Appearance
❍
Warranty
Do you . . . ?
❍
Own a House. If yes,
how many square feet?
❍
Own a Town House/
Condominium/Co-op
❍
Rent an Apartment
❍
Rent a House
Are you interested in
receiving literature on
other Niles products?
❍
Yes
❍
No
Are there products/
capabilities that you would
like to see introduced?
WARRANTY REGISTRATION CARD
Page 20
N i l e s A u d i o C o r p o r a t i o n
1 2 3 3 1 S . W . 1 3 0 S t r e e t M i a m i , F l o r i d a 3 3 1 8 6
D e s i g n e d a n d E n g i n e e r e d i n U S A
M a d e i n C h i n a
©2005 N il es A ud io C or po ra ti on . All rig ht s re se rv ed . Ni le s, t he N il es l ogos and Bl en di ng
High Fi de li ty a nd A rc hi te ct ur e are reg is te re d tr ad em ar ks o f Ni les Audio C or po ra ti on . Al l ot he r tr ademarks a re
the p ro pe rt y of t he ir r es pe ct ive owner s. 1 0/ 05 D S0 04 13 BC N
B L E N D I N G H I G H F I D E L I T Y A N D A R C H I T E C T U R E
®
Loading...