Niles AC-8DSS installation Manual
INSTALLATION & OPERATION GUIDE
™
Intelligent Power Management Systems.
AC-8DSS
AC-8DSS
8 OUTLET POWER MANAGEMENT SYSTEM
B LENDING H IGH F IDELITY AND A RCHITECTURE
®
IMPORTANT SAFETY PRECAUTIONS
Your iPOWER™product represents the latest in power management and protection technology.
However, like any electronic device, an inappropriately or improperly installed device may not perform as intended. By following a few common sense precautions, your iPOWER
you a lifetime of worry-free performance.
The following safety precautions apply to all iPOWER™products.
READ AND OBSERVE THE FOLLOWING SAFETY PRECAUTIONS AT ALL TIMES.
™
product will give
WARNING! Power Source:
3 prong adapter. iPOWER
Use only with a 3-prong standard AC outlet or a GROUNDED 2 to
™
products cannot provide power protection without a grounded AC
source. Never use a 3 to 1 adapter plug — this will disable all protection from your iPOWER
unit and will void the Limited Lifetime Warranty and Connected Equipment Guarantee.
All rooftop devices connected to your iPOWER
™
products should be grounded according to
the National Electrical Code (NEC). Do not place any rooftop device where it can come into
contact with power lines or any power circuit.
WARNING! Operating Voltage: Any equipment plugged into an iPOWER™product must have
a 120V, 60Hz rating.
WARNING! Power Rating: Check the power consumption (watts) of each device that will be
powered by an iPOWER
™
product. Be sure that the total of all devices being connected does
not exceed 1800 watts.
WARNING! Water and Moisture: Do not use any iPOWER™product in an area where it may get
wet, such as near a bathtub, sink, laundry facility, in a wet basement, or near a swimming pool.
WARNING! Ventilation: While iPOWER™products do not generate a significant amount of heat,
they should not be placed directly on a bed, rug, or sofa that may obstruct the unit’s natural heat
dissipation abilities.
™
IMPORTANT SAFETY PRECAUTIONS
CAUTION! Heat: iPOWER™products should not be placed on or in close proximity to heat sources
such as radiators, heat registers, stoves, or on top of other devices (including amplifiers and receivers)
that produce heat.
WARNING! Power Cord Protection: Power cords and remote trigger cables should be routed
so that they are not likely to be walked on, chewed by pets, or pinched by objects placed on
them. Pay special attention to the place where the cord meets the plug and where the cord
enters the device.
WARNING! Object And Liquid Entry: Care should be taken that no objects or liquids fall
onto or into the device. Do not use alcohol on the device.
WARNING! Damage Requiring Service: Customers should not attempt to repair iPOWER
products. These devices should be serviced by an authorized service technician when:
• The power supply cord or the plug has been damaged
• Objects have fallen, or liquid has been spilled, into the device
• The device has been exposed to rain
• The device shows a marked change in performance or does not appear to function normally
• The device has been dropped, or the enclosure has been damaged
™
CONGRATULATIONS!
Thank you for purchasing a Niles iPOWER™Intelligent Power Management System.
Niles iPOWER
are the most advanced and complete power management devices available.
With iPOWER
™
products are the result of years of research and development and
™
in your system, you have complete confidence knowing that your
audio/video components have a clean power supply free of noise and distortion.
The result—your home entertainment system will perform as is designers intended,
while being fully protected from electrical noise and potentially damaging spikes
and surges.
In addition to power protection and performance enhancement, the iPOWER
™
AC-8DSS offers triggering options which allow for control of your system’s start-up
and shut-down procedures. With a little planning, your AC-8DSS can put control of
your home entertainment system at your fingertips.
Niles manufactures the industry's most complete line of custom installation components and accessories for audio/video systems. For a free full-line catalog write:
Niles, Catalog Request, P.O. Box 160818, Miami, Florida 33116-0818 or visit our
web site at www.nilesaudio.com
.
1
TABLE OF CONTENTS
INTRODUCTION 3
KEY TECHNOLOGIES 4
UNIT DETAILS 8
INSTALLATION OVERVIEW 9
PACKAGE CONTENTS 10
PLANNING YOUR SYSTEM 11
PLANNING YOUR AC CONNECTIONS 13
MAKING CONNECTIONS 14
TROUBLESHOOTING 16
SPECIFICATIONS 18
NOTES 19
TABLE OF CONTENTS
2
INTRODUCTION
INTRODUCTION
Never in the history of power protection has there been a product line that has
revolutionized the industry the way that Niles' iPOWER
Management Systems represent a breakthrough in three main areas:
filtration,
fastidious execution, iPOWER
and power management. Based on solid scientific principles, clever engineering, and
™
devices are built to the most stringent standards in the industry and
provide the maximum electrical protection and advanced performance enhancing technology.
iPOWER's i3™(instantaneous, impenetrable, and virtually indestructible) three-stage power protection circuitry stands head and shoulders above the industry in terms of delivering instantaneous
response time. Its clamping levels are among the lowest in the industry, providing unrivaled
electrical protection for its connected equipment. Its iQ
technology has the ability to reduce detail-obscuring “noise” on the AC power line, resulting in
performance that’s sure to please even the most demanding eyes and ears. In fact, iPOWER
be the first "audiophile-approved" power protection technology available at any price. Additionally,
its iDefinition
™
HDTV-ready coax circuitry provides protection while minimizing signal loss from
input to output so images are razor sharp and colors are vivid. Plus, with a full complement of true
line diagnostics, an intuitive, flexible triggering protocol, and user-friendly one button operation,
your AC-8DSS puts you in complete control of your system.
™
has. iPOWER™Intelligent Power
power protection, noise
™
Optimal Q Impulse Noise Filtering
™
may
8 Outlet Power Management System
Model AC-8DSS
3
KEY TECHNOLOGIES
i3™Three-Stage Circuit Topology — Power Protection for the Real World
iPOWER's i3™(instantaneous, impenetrable, and virtually indestructible) circuit topology represents
a breakthrough in power protection technology. A three-stage design comprised of Gas Tubes, Metal
Oxide Varistors (MOV's) and a proprietary Low-Impedance In-Line Filter, the i3
instantaneous protection.
Most MOV-based surge protection devices use a circuit topology that is sacrificial in nature. Like an
air bag in an automobile, they are designed to “blow up,” sacrificing their internal circuitry in order
to protect the connected equipment during a severe surge event. Sooner or later they fail in the line
of duty leaving connected equipment unprotected. As a radical departure from this philosophy, all
Niles iPOWER
design enables iPOWER
While UL’s
with i3
iPOWER
™
products with i3™protection technology are non-sacrificial in nature. This unique
™
to protect your equipment time and time again.
®
most rigorous standard for voltage let through is 330 volts, Niles iPOWER™products
™
protection technology have a consistent clamping level of less than 300V. In addition, all
™
products clamp at a mere 40V over peak standard line voltage (ANSI/IEEE C62.45
6000V 100 kHz Ring Wave Test), adding a level of protection rarely found in the industry.
iQ™Optimal Q Noise Filtration
All of the Power — None of the Noise. Computers, household appliances, and RF broadcasts can
introduce "noise" onto the AC power line, obscuring audio detail and video resolution. By their very
nature, conventional AC power line noise filtration circuits limit electrical current flow, stealing the
“punch” from high-current power amplifiers. The Niles iPOWER iQ™optimal Q impulse noise filtration circuitry simultaneously achieves both noise reduction and the proper power line loading
necessary for dynamic performance. Through careful research and with the deployment of
advanced electrical components, a sophisticated
design that varies the Q of the circuit topology was
created. With this design, iPOWER
an outstanding 50dB of common mode rejection and
60dB of differential mode rejection—without current
iQ™reduces up to 99.9% (60dB) of AC power line noise.
The above graphics simulate AC power line noise r
eduction.
choking. iPOWER™delivers both the performance
and the power.
™
circuitry delivers
™
products achieve
KEY TECHNOLOGIES
4
Loading...