Nikko Co RP7200H Users manual

KMNA-060009
NM0-010605
RECHARGING
"WARNING! USE UNDER THE DIRECT SUPERVISION OF AN ADULT."
The newly purchased Ni-Cd pack is not charged. Charge before operating.
1. Join the connector of the charger to the connector of the Ni-Cd battery pack.
2. Plug the charger into an electrical outlet.
3. Recharge for about 4-5 hours.
4. When the recharging is over, plug out the charger from the electrical outlet and detach the connectors.
Press
Battery’s
Connector
Charger
Charger’s connector
When playing for the first time after purchase, or after a long interval, the battery power may be weak. Even after recharging, the playing time can be relatively short. The battery will gradually regain power after 2 or 3 repetitions of usage and recharging.
Ni-Cd battery pack
Household
CAUTION
Do not charge Battery Pack immediately after use. Wait until it has cooled before charging. Avoid short circuits. Short circuits will cause overheating, burning of the cords and other damages to the
battery Pack and Charger. The Ni-Cd Battery Charger should be used for charging one Battery Pack. Do not use the Charger for
charging. Do not charge near fires, where the temperature is extremely high, or where it is wet or damp. The charger will become slightly heated while charging. Allow sufficient free space around the Charger. If the power of the battery pack is weak in spite of proper charging, the batteries may be worn out from
repeated use. Replace it with a new Ni-Cd battery pack. Dispose of use Ni-Cd battery packs correctly. Disconnect the supply before making or breaking connections to the battery. Only use batteries or accumulators of the recommended type or a similar type.
WARNING AGAINST RECHARGING NON-RECHARGEABLE BATTERIES.
Please use this battery charger only for the charge of the rechargeable battery pack. The Ni-Cd battery pack should be charged under the supervision of an adult.
VEHICLE
TOP VIEW
BOTTOM VIEW
outlet
2
PREPARATION FOR STARTING OPERATION
1. ATTACHING ANTENNA TUBE
Pass the antenna wire through the antenna tube, then insert the tube into the antenna tube holder.
If the antenna tube cannot be successfully inserted into the antenna tube holder, try holding the root of the antenna wire with fingers of one hand and extending the wire with fingers of the other hand.
* Note: Be careful not to pull antenna wire too strong.
2. INSTALLING TRANSMITTER ANTENNA
Place the transmitter antenna into the antenna holder to screw it in clock-wise.
Do not extend the antenna when installing. It’s dangerous. If the antenna is not screwed in securely, the vehicle may move erratically. Screw the antenna securely.
Antenna wire
Antenna tube
Antenna tube holder
Transmitter antenna
3. INSTALLING THE BATTERIES
TRANSMITTER
To remove the battery lid, press the point marked “OPEN” and pull the lid downward.
One 9 volt (006P) battery
Install battery make sure that (+) and (-) poles are positioned properly.
* Dispose the used batteries separately from other trash.
3
ON
OFF
4
USING THE CONTROLLER
O
FF
ON
(1)
Extend transmitter antenna to its full length. The vehicle can be controlled from a long distance by holding the transmitter higher with the antenna straight up.
(4) Start operating the vehicle.
FF
O
(5) Turn “OFF” the vehicle.
N
O
(2) (3) Turn “ON” the vehicle.
Turn on the transmitter by operating the control stick. (The power indicator will light up.)
Forward / Reverse
control stick
FORWARD
STOP
(NEUTRAL)
REVERSE
CAUTION:
(6) Remove all the batteries from the vehicle and the transmitter.
Steering
control stick
LEFT / STRAIGHT / RIGHT
Red LED
power indicator
ADJUSTING WORKING LIGHT FUNCTION
5
TO ADJUST STEERING ALIGNMENT
Adjust the steering alignment when the vehicle does not run straight forward.
Turn the steering alignment lever towards “L” if the vehicle runs towards right.
L R L R
Turn the steering alignment lever towards “R” if the vehicle runs towards left.
678
Loading...