Niigata seiki DEI-233S1, DEI-233S2 Instruction Manual

SWISS MADE

MODE SET

SWISS MADE

MODE SET

ＣＲ２０３２

＋

IP65 class waterproof rating
Small size
ABS and REL measurement modes
ABS mode: With Display Hold
REL mode: With one touch Preset recall
Direction of measurement (＋ / −) switchable
Preset function
Auto-off feature (approx. 4 hour

)

※REL mode only

Made in Switzerland

●

●

●

●

●

●

●

LCD Display

[

SET] Button

Stem
(

Mounting Shaft

)

Spindle

Contact Point

[

MODE] Button

Battery Cover

Model No. DEI-233S1/DEI-233S2 <combined>

Thank you for purchasing the Digital S-Line Indicator.
For proper operation, please read this manual thoroughly before use.

DIGITAL S-LINE INDICATOR（IP65）

Accessories

ＣＲ２０３２

CR2032

(

Lithium Cell

)

※Included for test

FEATURES

BATTERY REPLACEMENT

①Remove the (2x) battery screws using (+) PH#0

screwdriver. Place a small standard screwdriver in
the notch to gently pry open the cover and slide out
the battery.

②Insert the new battery following the polarity markings

on the cover.

③Replace Battery Cover and tighten screws to secure.

SPECIFICATIONS

YES

φ8mm

70g

5〜40℃

CR2032(Lithium cell)×1

DEI-233S1

0.001mm0.01mm

0.01mm

0.01mm/0.001mm
(

switchable

)

0.02mm

0.002mm

up to ±130mm

0-12.5mm

Less than 1.5N

0.005mm

DEI-233S2

Model No.

Measurement Range

Resolution

Displayed Resolution

Accuracy

Measurement Force

Repeatability

Preset

Measurement Dir. Switchable

Mounting Shaft Diameter

Operating Temp. Range

Power Supply

Weight

Battery

Battery Cover

Battery Cover

Notch

PARTS IDENTIFICATION

NOTICE

Use only CR2032 type battery.

See Reverse for “How to Use”→

TROUBLESHOOTING

Error Condition Corrective Action

Measured value is
wrong

Clean measuring surfaces with lens
tissue or similar.
Confirm and re-set 0-Point setting.

●

●

LCD does not
display
Displayed value is
unstable
Display is hard to
read

●

●

●

Cycle power by removing and
replacing battery.
Replace battery with new one.

●

●

※If problem persists, or if you have any questions, please contact distributor

or place of purchase.

※Please note, manufacturer is unable to respond to inquires or provide

service directly. Please contact distributor or place of purchase.

Read Error.
Reset the sensor by pressing the
[

MODE] or [SET] button.

※If message is displayed again, there

is possibility that the memory is
corrupted; Please contact distributor
or place of purchase.

“Err 0” is Displayed
on LCD

INSTRUCTION MANUAL

①Mount indicator securely, such as on optional Magnetic

Base, and make sure that the Spindle is perpendicular
to the measurement surface.

②Press [MODE] or [SET] to turn on power.
③Setting 0-Point.

＜REL Mode＞
 With gauge in contact with reference surface, press the

[

SET] button.

Display will read “0.00mm.”

＜ABS Mode＞
 With gauge in contact with reference surface, press the

[

MODE] button. When display reads “SEt”, press the

[

SET] button. (ref. “Function Setup - Preset Function”

)

Display will read “0.00mm.”

※If “0.00mm” is not displayed, please refer to “Function

Setup - Preset Value” to set value to 0.00mm, and then
perform steps ① to ③.

④With Gauge body held fixed, and the probe in contact

with the workpiece, the LCD will display the difference
between workpiece and reference plane.

●

●

●

●

●

●

●

●

●

This is a precision instrument, handle with care. Do not
drop or subject to excessive forces.
Keep away form high voltage and strong magnetic fields;
instrument damage may result.
Do not use or store in direct sunlight or locations with
high temperatures such as in a car, or near a stove or
heat source.
When taking measurements, hold gauge securely, such
as in magnetic base. (sold separately

)
Please do not disassemble or modify.
Remove dust and cutting chips after use and apply rust
preventative oil to metallic surfaces. Please keep out of
reach of children.
Do not use organic solvents to clean the body of the
instrument.
When not being used for a long period of time, please
remove battery.
Only use as directed. Improper use may cause accident
or injury.

※If no operation is performed after 5 seconds, display

will return to the measurement screen.

【ABS / REL Mode】

※This function not available.

【Preset Value】

Numerical value can be preset,
and later called up to
measurement screen.

ABS

【Measurement Direction】

【Measurement Screen】

Switchable between ABS or REL
modes.

＜ABS mode＞

●Press [SET] Button to hold the

displayed reading. Press once
and “H” icon will show, and value
will hold. Press again to release.

＜REL mode＞

●At any probe position, press the

[

SET] button to call up and
display the Preset Value.
(

see “Preset Value” below

)

【Preset Function】

Preset Value set can be called
up for display.
※For use in ABS, or REL mode.

【Resolution】

※DEI-233S2 only

I299-K 1604

Niigata seiki Co., Ltd.

6-15-22, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : [phone] Fax. : [phone]

MAIL [e-mail]
URL http://www.niigataseiki.co.jp

HOW TO USE

Press the [MODE] button to cycle through the functions in
the sequence shown below. When desired function is
displayed, press [SET] button to access the various settings.

FUNCTION SETUP

CAUTION

Press [MODE] to display ABS / REL,
then press [SET] to select.

To Set

Press [MODE] to move cursor, and
press [SET] to change value.

To Set

Press [MODE] to display “Inc” (+) /
“dEc” (-), then press [SET] to select.

To Set

Press [MODE] to display 0. 01 / 0. 001,
then press [SET] to select.

To Set

[

MODE] Button

[

MODE] Button

[

MODE] Button

[

MODE] Button

[

MODE] Button

[

MODE] Button

[

MODE] Button

【Power ON】

Press [MODE], or [SET] button to turn on power.

【Power OFF】

Press and hold the [SET] button to turn off power.
※Power will switch off automatically if idle after

approximately 4 hours.

(※REL Mode only

)

※When battery level is low, the 『 』 icon is displayed;

please replace battery.

POWER

B