Night Guard Home Surveillance System C3-RS-727A LCD User Manual
1
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
C3-RS-727A LCD
PROFESSIONAL 2-WAY LCD REMOTE CAR
STARTER & ALARM SYSTEM
With
Built in Temperature sensor
And Two-way Serial Port Data Link
Compatible
Please see page 23 of this manual for more details
OPERATION MANUAL
Please register your pr oduct at:
www.autopageusa.com
2
Automatic Re
-
Arm
TABLE OF CONTENTS:
A BATTERY REPLACEMENT
B THE REMOTE LCD ICONS WITH FUNCTION
C PROGRAMMING OF THE LCD REMOTE TRANSMITTER
1. Screen Lamp ON
2. Power Save Mode
3. Clear The Flash Icon and Melody Sound
4. Stop The Melody Sound.
5. Button Lock
6. Vibration / Melody Mode
7. Enable / Disable Bi Sound While Pressing Button:
8. Low Battery Indication.
9. Set Up Fixed Count Down Timer
10. Out Of The Range Check
D CLOCK & TIMER SETTING
1. Clock Setting.
2. Alert Alarm Timer Setting
3. Count Down Timer Setting
4. Time Set-Up For “Daily Timer Start”
REMOTE TRANSMITTER OPERATION
A. REMOTE TRANSMITTER OPERATION
B LCD DISPLAY TRANSMITTER OPERATION
C LED DISPLAY
D CHIRP INDICATOR
E PARKING LIGHT
F ALARM OPERATION CONDITION
G ACTIVE ARMING – ARM & LOCK
Defective Sensor Reminder
Silent Arming / Disarming
Shock Sensor By -Pass
Hidden Alarm Function
H PASSIVE ARMING
Passive Arming with Passive Door Locking
Passive Arming By-Pass
I ACTIVE DISARMING – UNLOCK & DISARM
Tamper Disarming
Pathway Illumination
Two Steps Door Unlock
J DISARMING WITHOUT A TRANSMITTER
Overrides the Alarm without Password Pin Code
Overrides the Alarm With Password Pin Code
K VALET MODE
Enter Valet Mode
Exit Valet Mode
L CAR LOCATOR
LCD REMOTE TRANSMITTER:
4
5
7
7
7
7
7
8
8
8
8
8
9
9
9
10
10
10
11
11
11
11
11
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
14
14
14
14
14
3
M PANIC FUNCTION
Noise Abatement Circuit
N TRIGGER THE SYSTEM
Clear The Trigger Icons and Melody Sound
Stop The Melody Sound Only
O ANTI CAR - JACKING
Active Anti Car Jacking
Passive Anti Car Jacking
Trigger The Anti Car Jacking Mode
Override The System To Turn Off Anti Car Jacking
P SYSTEM’S TRIGGER CHECK
Q SYSTEM’S STATUS CHECK
R DRIVER PAGING (OPTION)
S DOME LIGHT CONVENIENCE DELAY & SUPERVISION
T IGNITION CONTROL THE DOOR LOCK/UNLOCK
U TRUNK RELEASE (CHANNEL 3) OUTPUT
V CHANNEL 4 TIMER CONTROL OUTPUT
W POWER ON MEMORY
X SECOND VEHICLE SECURITY SYSTEM OPERATION
Programming 2nd car transmitter
For Standard Remote Transmitter
For 2-Way LCD Display Transmitter
REMOTE START OPERATION:
A TO REMOTE START THE VEHICLE
Safe Start (Child safety mode)
B TO OPERATE VEHICLE WHILE RUNNING ON REMOTE START
C TEMPORARY STOP FEATURE
D TURBO CHARGE MODE
E TIMER / TEMPERATURE START
3 (2) Hours Timer Start With Temperature-Control Off
3 (2) Hours Timer Start With Temperature-Control
Daily Timer Start
Exit the Timer Start
F TEMPERATURE CHECK
G TO TURN OFF THE REMOTE START
H SHUT-DOWN INPUT FOR REMOTE STARTER
I DISABLING THE REMOTE START SYSTEM
Congratulations on your purchase of the RS 727A LCD remote start vehicle security
system. We sincerely hope the purchase of the RS727A remote start security system
gives peace of mind to you.
The RS727A LCD is a state-of-the-art two -way communication system. Please take
the time to read over this manual to thoroug hly familiarize your self with the many
features and options of the RS727A.
14
15
15
15
15
16
16
16
16
16
16
16
16
17
17
17
17
18
18
18
18
18
19
19
19
19
20
20
20
20
20
21
21
21
21
4
Auto Page, Inc. has over 25 years of experience in the vehicle security industry in the
United States and is a wholly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
Iwata has been an industry leader for over 50 years, establishing a reputation for
ingenuity in its engineering capability and innovative communication products. Auto
Page and Iwata maintain a long tradition of providing the best value to their customers.
TRANSMITTERS
The RS727A comes with two transmitters. The XT72LCD is a 2-way transmitter and
receiver, also referred to as a transceiver. The XT-65 is a mini-size 1-way transmitter.
Both operate on the AM band with a code -rolling feature that will prevent any illegal use
of a code -grabber attempting to record and steal the codes of your transmitter.
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT-73LCD: This transmitter uses a standard 1.5-volt AAA battery. Information on
changing the battery can be f ound on page 5 of this manual.
XT-65: This transmitter uses one (1) 3-volt lithium ion battery (#CR2032) that is
placed with the (+) side facing upward. To replace the battery, you will need to use a
small flat blade screwdriver and a small Philips screwdriver. Remove the small
Philips head screw. Then locate the small notch on the lower right side of the
transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the
top case from the bottom case. It should snap apart after breaking the seal. Before
removing the battery note the direction of the positive (+) terminal. Place the new
battery in exactly the same manner, being careful not to bend or damage the contact
terminal. Snap the cases back together and then test the transmitter to insure it arms
and disarms the alarm. Reinstall the Philips screw to finalize the battery replacement.
XT-65 Extended Range Sliding Cover remote
CR2032 3-Volt Battery
5
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personn el that the vehicle can be started automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. The vehicle windows must be rolled up.
7. Should the unit malfunction, disconnect the fuse until the problem is corrected.
8. The use and operations of this system is the sole responsibility of the operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle running on
public streets.
10. It is not safe to remote start the vehicle if the vehicle is parked on a steep incline.
LCD REMOTE CONTROL TRANSMITTER:
Note: If the system is interfered by stronger radio
frequency around, sources of high voltage electric
power or such Obstacles like tall buildings and so
on, the transmission range may get shorter as the
system uses low out put powered frequency.
6
A. BATTERY REPLACEMENT:
s
econds before using (See Timer Setting).
r are within range of the
3-hour.
A 1.5V type AAA Alkaline battery powers the
Remote Transmitter. When the power of the
battery weakens a icon shall be
displayed on the LCD screen. When the old
battery is replaced to new one, there will be
beep sounds indicate the power is up and the
clock on the LCD screen returns to AM12:00
after displaying all the icons.
Correct the time by pressing for 3
Note : Press the button two times when the battery compartment is
empty, then insert the new battery
B. THE REMOTE LCD ICONS WITH FUNCTION:
Door Lock
Your vehicle doors are
locked
Armed Mode
Your vehicle is in armed
mode
Remote Transmission
You are transmitting the
signal to control unit
Door Open Warning
Doors are illegally opened
(Zone 3)
Door Unlock
Your vehicle doors are
unlocked and the system is
Disarmed
Valet Mode
All the function shall be
temporarily on hold.
In – Range Indicator
You
remote control
Trunk/Hood Trigger
Trunk or Hood is illegally
opened (Zone 2)
Shock Sensor Trigger
Trigger on Shock Sensor
(Zone 4)
Engine Starting
Your vehicle engine
starting by remote control
Timer Control Start
Start the Engine
automatically at the same
time next day or every
Time Monitor
Count Down Timer
Reminder when time is up
for parking
Warn Away trigger
Trigger on Shock Sensor
(Zone 1)
Engine Running
Your vehicle's engine is
running
Temperature Monitor
Indoor temperature of your
vehicle
Alert Alarm
You have set morning call
alarm
Power Save Mode
Save the battery power
7
Vibration Mode
1 melody sound to confirm enters
Mode
Remote Control vibrates
when the system is
triggered
Driver paging
Someone is paging you in
front of your vehicle
Button Lock
Disable the transmission
function temporarily
Low Battery
You have to replace the
battery of remote control.
C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER:
Transmitter Button Description Operation
(1 second)
(3 seconds) Timer Programming Mode.
(5 seconds) Power Save Mode
- -
- (2-second)
- (2-second)
- (2-second)
- (2-second)
LCD screen lamp turns on for 5
seconds.
Clear the Flash Icon and
Melody Sound on the LCD
Screen Transmitter
Button Lock ( ) enable /
disable
Melody / Vibration ( )
Program Count Down Timer
( ) (10-Minute / 20M / 30 M
/1Hour /1.5H / 2.0H)
Enable / Disable Bi Sound (Bi)
While Pressing Button
Press and hold for 1 second
1 melody sound to confirm enters.
Press and hold for 3 seconds
2-melody sounds to confirm enter .
Press and hold for 5 seconds
Press within 3 seconds
Press within 3 seconds and Hold
button for 2 seconds
Press within 3 seconds and Hold
button for 2 seconds
Press within 3 seconds cycling
*leave the buttons starting count
down then flashes
Press within 3 seconds and Hold
button for 2 seconds
1. Screen Lamp ON: Press and hold the button one second, one melody will
sound and the LCD screen lamp will turn on for 5 seconds.
2. Power Save Mode: While in the power save mode, the
LCD remote transmitter uses “0” current to save the
battery power.
Entry: Press & hold the button for 5 seconds, one
melody will sound and the icon on the LCD
screen indicates entry of the “power save mode”.
Exit: Press any button of the LCD remote transmitter to
8
exit the “Power Save Mode”.
show the LCD remote transmitter is on “Button Lock”
is useful when you are in a noisy place and it is difficult to
3. Clear the Flash Icon and Melody Sound: Pressing the button 3 times
within 3 seconds will clear the flash icon and the melody sound on the LCD screen
transmitter.
4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen
will alert the user through a melody sound and a flashing trigger icon. Press any
button on the LCD remote transmitter to stop melody sound only.
5. Button Lock: This is useful if you want to disable the
transmission function of the remote control temporarily to
prevent from any inadvertent pressing of buttons by others.
Press the button first, within 3 seconds press and hold
( ) button for 2 seconds to activate or cancel the button
lock function, the icon will displayed on the LCD screen to
6. Vibration / Melody Mode:
This
hear the beep sound from the remote control. In this mode,
the remote control vibrates itself if your security system is
triggered.
Press the button first, within 3 seconds press and hold
( ) button for 2 seconds to select the mode of vibration
or melody, the icon will displayed on the LCD screen to
show the LCD remote transmitter is on vibration mode.
7. Enable / Disable Bi Sound While Pressing Button :
It has a short “bi” sound while pressing the button of the LCD screen transmitter
If you want mute the “bi” sound mute always while press button. Press the
button first, within 3 seconds press and hold the (Bi) button for 2 seconds to
disable the “bi” sound.
8. Low Battery Indication:
When the power of the battery weakens, it has two short “bi” sound and flash
icon while pressing the button of the LCD screen transmitter.
9. Set Up Fixed Count Down Timer:
1. Press the button first, within 3 seconds press and hold the ( ) button
for 2 seconds, the LCD screen will show the icon and timer (i.e. 0:10),
Loading...