Assembly Instructions
Parts Packed in this Box.
1A
Please Note: The parts shown below are Full size.
The other sizes differ only in overall length.
Stretchers x 2 pieces
Futon Body Assembly
Chair • Love seat • Full • Queen
TM
Full and Queen size only:
1B
Strong Back assembly.
Strong Back x 1 piece
TM
BronzeS H O E F I T T I N G S
ND 1004
Snapper Snapper
Back Deck
Seat Deck
Queen size only: Extra parts in this box.
1C
Short Legs
x 2 pieces
featuring the Rubber
Back Deck Top Roller (Code A2)
Back Deck Bottom Roller (Code A1)
Seat Deck Pin (Code A3)
S H O E F I T T I N G S
US Patent #6,715,166
Other Patents Pending
50mm Bolts
x 2 pieces
TM
TM
40mm Bolts
x 4 pieces
Use the Short Bolts (40mm)
To attach the Strong
Back to the Back
Deck.
Allen Key
x 1 piece
Page 1 of 5
Assembly Instructions
Attach Stretchers to Arms
Chair • Love seat • Full • Queen
Prepare Arms for Assembly.
2A 2B
TM
BronzeS H O E F I T T I N G S
ND 1004
Attach Arms to Stretchers.
NOTE: The hardware for these steps is
included .in the ARM box.
Fasten Stretcher Brackets to the Arms:
Dowel Hole
Hole for Bolt
Hole for Cleat
Leg
A. Insert the Stretcher Bracket Cleat into the
hole provided.
B. IMPORTANT: Don't fully tighten Bracket until
Stretchers are all in place for easy alignment.
Stretcher
Bracket
16mm Bolt
Allen Key
Fit Wooden Dowels to
Stretchers:
Middle
hole
Wooden Dowel
Stretcher
Tap dowels all the way into the middle
hole at each end of the Stretchers.
Cleat
Using Bolts and Barrel Nuts provided with the Arms,
attach the Arms LOOSELY to the Stretchers as shown..
It is important that these bolts are left LOOSE!
Rear stretcher ( no plates )
Bolts
Barrel Nuts
The Front Stretcher has metal plates which should face upwards.
Allen Key Leave bolts LOOSE!
Wooden
Bolts
Dowel
BOLT AND BARREL NUT
ASSEMBLY SYSTEM
Insert Barrel Nuts as shownusing a
screwdriver. This will help you position
the Nut in line with the Bolt.
Do not force the Bolt
as you may strip the
thread. Be sure the
thread is properly started.
Allen Key
Bolt
Bolt
THIS END
FRONT
Bolts
Do not tighten
the Bolts at
this stage!
Be sure the holes are
free of wood chips
and saw dust.
Barrel Nut
Screwdriver
Page 2 of 5
Assembly Instructions
Fit the Back Deck into Position:
3A
Fit the Back Deck
Chair • Love seat • Full • Queen
Your arm style may vary
For Queen size frame only:
3C
Attach the short legs.
TM
BronzeS H O E F I T T I N G S
ND1004
All four joints must
be left LOOSE.
Insert the Back Deck lying
flat. Insert one end first, then
gently lower the other end into position.
Remember that the Bolts on the Arm should be LOOSE.
Be careful not to scratch the Arms with the Plastic
Runners when you lower the ends of the Back Deck.
Tighten all the Bolts.
3B
Tighten all the Bolts.
CAREFUL !
These can
Scratch the
Arms
Please Note:
Use 2 People!
Using the extra 50mm bolts, attach
the Queen short legs to the back deck.
The exposed part of the metal nut
in the leg should be oriented away
from the bolt for proper assembly.
50mm Bolt
Queen
short leg
When you have the Back Deck fitted
lying flat, tighten all the Bolts.
Page 3 of 5
Tighten all the Bolts.
Assembly Instructions
Hook the Seat Deck onto the Snapper.
4A
Fit the Seat Deck
Chair • Love seat • Full • Queen
Lift the Seat Deck in vertically, so the Pins
meet with the Rubber Snapper. The head of
the Snapper should fit between both Pins.
Just remember:
•The Top Pin - fits over the top,
•The Lower Pin - goes underneath.
Top Pin
- over the top
Pull the Seat over the "Snap Point."
4B
You will need to Pull Hard.
TM
BronzeS H O E F I T T I N G S
ND 1004
Put your
foot here
Please Note:
Use 2 People!
Push down on the Seat, and the
4C
Back will Lift.
Push the Seat
down further and the
Back will rise until it is
in the "Lounge Position"
Rubber
Snapper
Bottom Pin
- underneath
This is the Lounge Position.
4D
Push
Push the Seat
with your knee, to
convert to the Sofa Position
Notch
With the Top Pin
inside the notch on
the Rubber Snapper, put
your foot on the Back Deck
and pull the Seat over the "Snap Point"
This is the Sofa Position.
4E
Add Mattress and
Enjoy! See separate page
for Operating Instructions.
Page 4 of 5
Assembly Instructions
5A
Lift from the front,
using both Handles.
Disassembly: Removing the Seat
Chair • Love seat • Full • Queen
Lift the Seat all the way.
5B 5C
Lift all the way until the
Top Pin drops into the
notch on the Rubber Snapper.
Rubber
Snapper
TM
BronzeS H O E F I T T I N G S
ND 1004
Push the Seat over the "Snap Point."From the Bed position, lift the Seat.
You will need to Push Hard.
Top Pin
Notch
From the Back, lift out the Top Pin and ease the Seat Deck forward.
5D
Lift and ease the Deck forward
Lift up so the Top Pin is out of
its notch in the Rubber Snapper.
Ease the Back Deck forward,
keeping it orientated vertically.
Rubber
Snapper
Please Note:
Use 2 People!
Page 5 of 5
Lift the Seat clear of the frame.
5E
Be careful when lifting the
Seat Deck out, not to scratch
the Arms with the Rollers.
Loading...