Night & Day Pelican Twin Bunk Bed Assembly Manual
A s s e m b l y I n s t r u c t i o n s
Pelican Twin Bunk Bed
!
SAFETY WARNING
Follow th e information on the warnings app earing on the upper bunk end structure and on
1.
the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
2.
the likelihood of entrapment or falls.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
3.
Do not allow children under 6 years of age to use the upper bunk.
4.
Periodically check and en sure that the guardrail, ladd er, and other components are in t heir
5.
proper position, free from damage, and that all connectors are tight.
Do not allow horsep lay on or under the bed and prohibit jumping on the bed.
6.
Always use the ladder for entering and leaving the upper bunk.
7.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
8.
Use of a night light may provide added safety precaution for a child using the upper bunk.
9.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
10.
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
11.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
12.
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
N&D 0307
Keep these instruc tions for future reference.
13.
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" width and 74"-75" long on upper bunk (twin size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is at
least 5" (127mm) below upper edge of guardrails.
Replacement Parts:
Replaceme nt parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Page 1 of 8
TM
A s s e m b l y I n s t r u c t i o n s
Pelican Twin Bunk Bed
N&D 0307
Parts in Box 1
1A
Upper Bunk
(Left Hand)
Lower Bunk x 1 Lower Bunk x 1
Parts in Box 3
x 1
Upper Bunk
(Right Hand)
Note: No Holes!
x 1
Hardware in this Bo x .
1B
Parts in Box 2
Upper Stretcher
Upper Stretcher x 1
Bottom Stretcher x 2
(with extra holes)
Ladder x 1
x 1
Rear Guard Rail x 1
Front Guard Rail x 1
Brackets x 4
Tools required for assembly:
•
Allen Key (supplied)
•
30mm Bolts x 2Wood Dowels x 25 Barrel Nuts x 19
Phillips Screwdriver
(not supplied)
Page 2 of 8
Set of Slats x 2
40mm Threaded
Wood Bolts x 8
100mm Bolts x 19 80mm Bolts x 16 Metal Tubes x 4
30mm Wood
Screws x 36
16mm Wood
Screws x 2
Long Allen Key x 1
Fit Wood Dowels to the
2A
Stretchers.
Stretcher
A s s e m b l y I n s t r u c t i o n s
Pelican Twin Bunk Bed
Attach Stretchers to Lo wer F rame .
2B
Using 100mm Bolts and Barrel Nuts provided with the Lower Frame,
attach the Lo we r F ram e to the Stre tc hers as shown .
N&D 0905
Middle
holes
Please Note:
Use 2 People!
Wooden Dowels
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
Be sure the holes are free of wood chips
and saw dust.
100mm
Bolts
Barrel Nuts
Stretcher
Lower Frame
Barrel Nuts
Barrel Nuts
100mm
Bolts
Lower Frame
100mm
Bolts
Page 3 of 8
Loading...