Night & Day Ginger Twin Loft Bunk Assembly Instruction
Page 1 of 7
N&D 0109
A s s e m b l y I n s t r u c t i o n s
Certified:
This bunk bed conforms to all applicable consumer product safety standards
16 CFR PARTS 1213, 1500, 1513 and ASTM F-1427
Replacement Parts:
Replacement parts, including additional guardrails may be obtained from any
Night & Day Furniture Dealer.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
SAFETY WARNING
!
SIZE OF MATTRESS AND FOUNDATION:
Use only mattress, which is 37 1/2" - 38 1/2" width and 74"-75" long on upper bunk (twin size.)
Ensure that the thickness of the mattress does not exceed 6" and that the mattress surface is at
least 5" (127mm) below upper edge of guardrails.
TM
Follow the information on the warnings appearing on the upper bunk end structure and on
the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both, to help prevent
the likelihood of entrapment or falls.
Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other components are in their
proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD–Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.
Ginger Twin Loft Bunk Bed
Page 2 of 7
N&D 0109
A s s e m b l y I n s t r u c t i o n s
Page 2 of 7
A s s e m b l y I n s t r u c t i o n s
Parts in Box 1 Parts in Box 3
Hardware in this Box.
1B
100mm Bolts
x 21
40mm Threaded
Wood Bolts x 16
Long Allen Key
x 1
30mm Wood
Screws x 16
16mm Wood
Screws x 2
Barrel Nuts
x 45
30mm Bolts
x 2
80mm Bolts
x 24
Wood Dowels
x 47
Note:
Tools required for assembly:
•Allen Key (provided)
•Philips Screwdriver (not provided)
Upper End Frame x 2
Lower End Frame
(Left Hand)
x 1
Note:
Extra Holes!
Lower End Frame
(Right Hand)
x 1
1A
Parts in Box 4
Parts in Box 2
Post L1
Left rear
Post R1
Right rear
Post L2
Left front Post R2 Right front
Set of Slats x 1
Ginger Twin Loft Bunk Bed
Ladder x 1
Front Guard Rail x 1
Rear Guard Rail x 1
Front Stretcher
(with extra holes)
x 1
Stretcher x 1
Long Frame x 1
Note: Extra Holes!
Page 3 of 7
N&D 0109
Ginger Twin Loft Bunk Bed
A s s e m b l y I n s t r u c t i o n s
Be sure the holes are free of wood chips
and saw dust.
Bolt and Barrel Nut Assembly.
Do not force the Bolt as you may strip the
thread. Be sure the thread is properly started.
100mm
Bolts
100mm
Bolts
100mm
Bolts
Barrel Nuts
Barrel Nuts
Barrel Nuts
Barrel Nuts
Long Frame
Stretcher--
*IMPORTANT NOTE:
Do not use the stretcher which
has extra holes. This is for the front
to attach the Front Gruard Rail.
Rear Guard Rail
Post L1
Post R1
100mm
Bolts
Assemble the Rear parts: Rear Guard Rail, Stretcher, Long Frame to Posts L1 & R1.
2A
Identify the Posts L1 & R1, as shown below and
lay them out on the floor. A carpeted floor is best
so as to not damage the wooden parts.
Tap wooden dowels into the dowel holes on
the ends of the Rear Guard Rail, Stretcher
and Long Frame. Use 100mm Bolts
and Barrel Nuts to join
them together.
Wooden
Dowels
Loading...