Page 1
EML7 LED High Output Emergency Light
INSTALLATION INSTRUCTIONS
Model: EML71UNVWH
WARNING
before beginning. All electrical connections must be in accordance with local codes, ordinances, and the National Electric Code. If
- Do not use outdoors.
- Do not let power supply cords touch hot surfaces.
- Do not mount near gas or electric heaters.
local codes.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- Do not use this equipment for other than its intended use.
- The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
- Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
- Operating temperature: 0°C - 40°C.
What’s In The Box
One (1) EML7
Installing the EML7
1
Preparation
• Carefully unpack the emergency light from its
packaging. Inspect product for defects due to
shipping.
• Become familiar with the wiring diagram before
beginning installation.
•
2
Mounting and Installation
Tools Needed
A Phillips screwdriver will be needed to install the
EML7. A drill is helpful to remove the knockouts and
mounting holes.
• Remove the center knockout and mounting holes on
the back plate by drilling or cutting out.
• Feed the power supply through the knockout.
• Mount the back plate to the junction box with
appropriate hardware.
• Connect the power supply (120/277 VAC) to the input
wires, using the provided wire nuts, according to the
wiring diagram in Figure 1
• Connect the battery to the LED board.
•
snap into place.
NOTE
Battery Testing: Allow 24 hours of charging before testing.
• Push In TEST Button - Fixture will switch to battery power and remain lit
• Release TEST Button - Fixture will switch back to AC power
NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com June 21, 2021 8:36 AM
Figure 1 - Wiring Diagram
Page 2
EML7 LED High Output Emergency Light
INSTALLATION INSTRUCTIONS
Model: EML71UNVWH
herein. Warranty does not cover improper installation, operation, alterations, power surges, overheating due to external conditions, or acts of nature including but not limited to lightning strikes.
will not exhibit cracking, peeling, excessive fading, or corrosion during the warranty period. Poles must be installed by a properly insured and licensed contractor, using the supplied anchor bolts and mounting templates. Using a
ALL NICOR WARRANTIES APPLY ONLY TO NICOR PRODUCTS THAT HAVE BEEN PURCHASED FROM AN AUTHORIZED NICOR DISTRIBUTOR; WHO PURCHASED THE PRODUCT DIRECTLY FROM NICOR; THE PRODUCT WAS NEW AND IN AN
UNOPENED NICOR PACKAGE AT THE TIME OF INSTALLATION; AND WAS INSTALLED BY A LICENSED ELECTRICIAN OR UNDER THE SUPERVISION OF A LICENSED ELECTRICIAN.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Consult the dealer or an experienced radio/TV technician for help
NICOR, Inc. 2200 Midtown Place NE, Albuquerque, NM 87107 P: 800.821.6283 F: 800.892.8393 www.nicorlighting.com June 21, 2021 8:36 AM
Loading...