REACTOR
80W BATTERY (TC)
INTRODUCTION
Thank you for purchasing the REACTOR battery. Please read
this manual carefully before using to ensure optimal lifespan
and performance.
The REACTOR is an advanced vaping system offering an
enormous 5000 mAh battery capacity and adjustable
power ranging from 1W–80W. Additional benefits of the
REACTOR include temperature control, extraordinary vapor
production, and the ability to customize settings. This
system is manufactured to the highest quality standards,
and when coupled with our line of premium e-liquids, offers
an exceptional vaping experience.
GETTING STARTED GETTING STARTED
It is important to turn “o” this device before storing.
There is no harm in leaving your REACTOR battery “on,” as
the battery life will not be consumed unless the ring button
is pressed. It is important however, to turn your battery “o”
when placing it in drawers, pockets, or purses to ensure the
button is not pressed inadvertently.
To turn the REACTOR battery “o,” follow the same steps used
to turn the battery “on.” Simply press the ring button ve
times in rapid succession, and the LED screen will go blank.
Please note, you will need to turn the REACTOR battery back
“on” again before using.
REACTOR batteries must be turned “on” before using for the
rst time.
To turn on your REACTOR, press the ring button on the side of
the battery ve times in rapid succession. Once the battery is
turned on, the digital LED screen will become visible. To use this
device, rst ensure the battery is “on” and the tank is lled with
e-liquid. Once ready, place your lips around the mouthpiece and
inhale while holding down the ring button. Release the button
at the end of each drag and repeat as desired. The wattage can
be adjusted to personal preference as described later in this
instruction manual.
REACTOR 80w
COMPONENT’S FRONT & BOTTOMCOMPONENT’S SIDE
FRONT VIEW
BOTTOM VIEW
FIRING BUTTON
OLED SCREEN
• Battery Indicator
• Resistance Level
• Wattage
• Voltage
• Temperature
• Coil Type
FIRING BUTTON
OLED SCREEN
UP/ DOWN
ADJUSTMENT
MENU
BUTTON
MENU
BUTTON
USB
CHARGING
PORT
POWER ADJUSTMENT
Overview
Adjusting the power (wattage) of your REACTOR battery oers
the ability to customize your vaping experience. Flavors taste
better at dierent power levels, so the ability to adjust wattage
allows users to nd the “sweet spot” of their favorite e-liquids.
Increased power will generate increased heat, which typically
results in warmer, more plentiful vapor production.
Adjusting Power
The wattage can be adjusted by pressing the “up” or “down” power
adjustment buttons until the desired level is reached. An increase
in wattage will translate to an increase in power. It is recommended
to start with lower levels and slowly increase the wattage.
POWER ADJUSTMENT
Advanced Users
Advanced users can further customize their vaping experience
by using coil heads of varying resistance. The resistance of the
attached coil head (ohms) can be viewed next to the battery
level indicator. Lower resistance coils will increase the power.
Locking the Wattage
Once a preferred wattage level is found, the device can be
locked to ensure the arrow buttons are not pressed accidentally.
To lock the wattage, press the up arrow and the down arrow
simultaneously for two seconds. Once successful, the LED
screen will display the word “Lock.” To unlock the device, repeat
the process until the LED screen displays the word “Unlock.”
TEMPERATURE CONTROL
TC Overview
The REACTOR battery oers advanced temperature control
(TC) functionality, allowing users to set a maximum coil
temperature. This is often used to maintain a consistent avor
prole while preventing “dry hits.” When a TC compatible
coil is attached to the battery, the corresponding mode must
be selected for the functionality to work properly. NI200 and
Titanium coils should never be used in Variable Wattage Mode
or red for extended periods of time.
The chart to the right indicates the available modes and
corresponding coil types required.
Mode Coil Material Temp Con trol
VW Any (Kanthal) No
TC-Ni NI200 Yes
TC-Ti Titanium Yes
TC-SS 316L Stainless Steel Yes
TCR -M1 Advanced Memory 1 Yes
TCR-M2 Advanced Memory 2 Yes
TCR-M3 Advanced Memory 3 Yes
TEMPERATURE CONTROL
TEMPERATURE CONTROL
TC Modes
To use the temperature control functionality, rst ensure a TC
compatible coil from the list on the last page is attached to the
device. Next, press and hold the “menu” button to toggle between
available modes. Release the button when the desired mode is
visible on the screen. The device can also be manually set to run
without temperature control by selecting the variable wattage
(VW) mode, bypass mode or smart mode. In variable wattage mode,
only overall power can be adjusted without the ability to limit the
maximum temperature. When setting the maximum temperature
of the coil, it is highly recommended to start low and slowly increase
the temperature. In bypass mode, the device can support a coil with
TEMPERATURE CONTROL
a resistance level within the range of 0.1 ohms - 3.5 ohms. Direct
voltage output system is applied in this mode. Therefore, the higher
the battery level, the higher the voltage output. In Smart Mode, the
wattage can be adjusted from 1W to 80W by pressing the up button
or down button only when an atomizer is installed on the device. The
Smart Mode will save one output power setting for each resistance
value and can totally save 10 groups of such proles. Once you
change the output power setting for a resistance, it will resave the
changed setting automatically. When the Smart Mode has already
remem bered 10 proles and you want to add anothe r new resistance,
the rs t saved prole w ill be delete d. When set in this mode, the device
can support a coil whose resistance is within the range of 0.1-3.5 ohms.
TEMPERATURE CONTROL
Note: When using a non-TC coil in one of the temperature
control modes by mistake, the device will automatically
switch to variable wattage (VW) mode.
Adjusting Wattage
When in a temperature control mode, the wattage output can
be adjusted from 1W - 80W. Keep pressing the “menu” button
and the up button simultaneously to increase the wattage
level. To decrease the wattage level, simultaneously press the
“menu” button and the down button.
Adjusting Temperature
When in a temperature control mode, the maximum coil
TEMPERATURE CONTROL
temperature can be adjusted from 200-600°F by pressing the
up button to increase and down button to decrease. Each
press of the up or down button will increase or decrease the
temperature setting by 10°F. Holding the up or down button
will rapidly increase or decrease the temperature.
Shift Between °C and °F
If you increase temperature to 315 °C and continue to press the
up button, the temperature reading will automatically change
to the lowest Fahrenheit (200°F). Equally, if the temperature is
set at the lowest Fahrenheit (200°F) and you continue to press
the down button, the temperature reading will automatically
change to the highest Celsius (315°C).
TEMPERATURE CONTROL TEMPERATURE CONTROL
TCR Mode Advanced
TCR (Temperature Coecient of Resistance) mode allows the
user to manually adjust the TCR values for dierent types of
wire to further improve on the accuracy of the device’s ability to
limit and sense an atomizer coil’s temperature. There are three
storage slots available (M1,M2,M3), each of which can store a
user dened TCR value. For your reference, the following table
indicates standard TCR value ranges for dierent wire types:
Material Nickel Titanium NiFe SS (303,304,316,317)
TCR Value Range 600-700 300-400 300-400 80 -200
Note: The TCR values listed above are 10X the actual
Temperature Coecient of Resistance.
M1 MODE VIEW
TEMPERATURE CONTROL TEMPERATURE CONTROL
Resistance Locking
Resistance Lock Mode allows the device to maintain the same
“base resistance” even though the coil resistance may increase
due to a rise in temperature. When locked, the device will
remember the last resistance used after a coil is removed and
then put back on.
In Resistance Unlock Mode, the resistance will be checked each
time a new coil is attached. After removing a coil, the screen
will display “New coil up same down” to check if the same coil
is being re-attached. If the same coil is being re-attached, press
the down button and if it is a new coil, press the up button.
Lock/Unlock Resistance
To lock or unlock the base resistance, ensure the device is
turned on and is set to one of the temperature control modes
(TC-Ni/ TC-Ti/TC-SS/TCR M1, M2, M3). The attached coil must be
at room temperature for the device to correctly set the “base
resistance.” Next, hold down the re button and up button
simultaneously for 2 seconds to lock or unlock the resistance.
The lock sign will appear when resistance is locked and “Ω”
symbol will come back when unlocked.
Note: Be sure to unlock the base resistance when you want to
change an atomizer or a coil to a dierent resistance.
BATTERY FEATURES
Switching LED Orientation:
The LED display can be rotated 180° based on user preference.
With the REACTOR battery turned “o,” press the “up” arrow
and the “down” arrow simultaneously for two seconds.
Overheat Protection
The REACTOR battery is equipped with overheat protection
which will automatically deactivate the device should its
temperature rise above 158° Fahrenheit (70° Celsius). If a
temperature above 158°F is detected, the REACTOR battery will
lock and the LED screen will display “temp protection” for the
next ve seconds. After this time, the device will unlock, the
display will return to normal, and you may resume vaping.
BATTERY FEATURES
Short Circuit Protection
The REACTOR is equipped with short circuit protection to
ensure your battery is not damaged by faulty tanks/coils.
Should a short circuit occur in the tank, the unit will not re,
and the LED screen will display “atomizer short.” Replace the
coil head in the tank, and your REACTOR battery will perform
again as intended.
Drag Time
Once the REACTOR ring button is pressed, the time elapsed
(in seconds) is displayed on the LED screen. The total drag
length will be visible for three seconds after the ring button
is released. This allows the user to track the length of each drag.
BATTERY CHARGING
When to Recharge
As you use the REACTOR, the battery will slowly drain and
eventually need to be recharged. The battery level indicator on
the LED screen will display the amount of battery life remaining.
The battery can be charged at any time, regardless of the
remaining charge. If the battery is completely drained, it will
need to be charged before continuing use.
Important Note:
It’s important to use only the REACTOR USB cable and wall
charger. Using components from other manufacturers may
cause irreversible damage to your REACTOR battery and
increase the risk of re due to potential voltage dierences.
BATTERY CHARGING
Charging Time
The REACTOR battery will typically take 6.5 hours to obtain a
full charge from its fully drained state.
How to Recharge
Attach the small connector of the USB cable into the charging
port of the REACTOR battery. The larger end of the cable should
then be inserted into a computer or other USB compatible
power source, or can be used in conjunction with the REACTOR
wall charger. Once connected to a power source, the battery
level indicator on the LED screen will ash until fully charged.
Once fully charged, the battery level indicator will stop
blinking, shine for 10 seconds and go out.
WARNINGS
Storage: This device should be kept out of reach of children and
pets, and stored safely in a dry environment. Do not store in
high-temperature areas, as this will cause irreversible damage
to batteries and other components.
Overheating: If the REACTOR vaporizes continuously or shows
any signs of overheating, stop usage immediately and unscrew
all parts.
Charging: Do not use the charger in damp areas or near a high
temperature heat source. If the power supply emits any heat or
odor, is discolored, or experiences any unexpected issues while
charging, unplug it immediately.
WARNINGS
Coil Resistance: The REACTOR battery is designed to work with
coils having a resistance of .1 ohms or above. Using coil heads
below .1 ohms will create a potentially unsafe situation.
Improper Usage: The use of any third-party accessories may
lead to malfunction and/or damage of this product.
Guarantee: The REACTOR oers a 30 -day satisfac tion guarante e
on all hardware. However, e-liquids and coil assemblies are
consumable items and will not be refunded.
Warranty: Claims for products damaged by improper usage
will not be accepted. This includes, but is not limited to, the use
of third-party hardware and/or improper handling.
110465
Nicopure Labs, LLC.
5909 NW 18th Drive, Gainesville, FL 32653
nicopure.com
Loading...