How it Works
Niagara
Loading...
GoStream Mini 400S
User Manual
22 pgs1.41 Mb0

Niagara GoStream Mini 400, GoStream Mini 400S, GoStream Mini 400H User Manual

Download
GoStream Mini 400 Encoder
User Manual
pg. 1
Contents
1. PRODUCT INTRODUCTION ............................................................................................................................................3
2. HARDWARE INSTALLATION ...............................................................................................................................................6
3. IP Finder ...........................................................................................................................................................................7
4. WEB UI .............................................................................................................................................................................7
pg. 2
1. PRODUCT INTRODUCTION
1.1 Product Brief
The GSM 400S has four SDI inputs while the GSM 400H has 4 HDMI inputs. Both models have an HDMI output The 400S model also has an SDI output while the 400H model has two HDMI outputs. There are also 4 x 3.5mm analog audio inputs for audio embedding and a 3.5mm analog audio output for audio de-embedding.
The front panel has PGM / feature buttons for users to control it locally. The USB3.0 interface allows the user to record in various formats. There are also record / snapshot / stream / connectivity buttons on the front panel.
The GSM 400 has one RJ45 for network connectivity. It also has an RS232 and 2 USB2.0 ports for users to connect with industrial / commercial controlling systems. The user can connect a USB keyboard and mouse to access the GSM 400 internal control interface.
Front panel
400H Back panel
pg. 3
Max. FPS
60/50fps @ 1920 × 1080p
Recording
Hardware Compression
Mode
Product
Photo
Input

Video
Interfaces
4 × HDMI (400H) or 4 x SDI (400S)

Audio
4 × 3.5mm
Output

Video
Interface
2 × HDMI (400H) or 1 x HDMI and 1X SDI (400S)

Audio
1 × 3.5mm
Video

H.264 baseline/main/high profile

Support input / output resolutions
1920 × 1080P60 (output 1920 × 1080P30)
1920 × 1080(P30/P25/P24/i59.94), 1280 ×720 (P60/P59.94/P30)
1024 × 768P30, 800 × 600(P60/P30)
720 × 480(P60/P30), 720 × 576P50
Audio

AAC-LC

Configurable bit rate range from 32Kbps to
384Kbps

Sample rate : 48KHz, 16bit
Network

1 × RJ45 for 10/100/1000Mbps Ethernet

DHCP client

Wifi:
1.2. Specification
pg. 4
802.11b/g/n
Support 150Mbps PHY rate

RTSP over UDP/TCP/Multicast/HTTP
Streaming

RTMP public (web portal)
protocols

TS over IP

HLS
Misc.

Web UI for system configuration
Features

Firmware upgradable

LED indicator
Status with Power Recycle

Main function switch
Record
Snapshot
Stream

PGM mode switch
Full screen
Quadview
Picture by picture
Picture in picture
PGM Loop

Full screen switch
Channel 1
Channel 2
Channel 3
Channel 4
2 × USB2.0 (For Keyboard and mouse usage)
1 × USB3.0 (For external storage usage)

1 × RS232 + 1 × RS485
Record
MP4 / TS / AVI
Format
pg. 5
2. HARDWARE INSTALLATION
2.1.
Package Contents
Item
Amount
GSM 400 Encoder
1
Power Adapter
1
2.2.
Device Size
Figure below is the size of the GSM 400.
pg. 6
Device Size Diagram
3. IP Finder
When the encoder is in DHCP mode you can use the IP finder to get the IP address. If you have multiple GSM 400s you can locate the one you want by the MAC address.
Don’t change the parameters on the right side. Just start the application and click the Search
button.
4. WEB UI
The Web UI is the interface for the user to control the GSM 400, users can control them via
normal PC or portable devices (EX: Android, iPhone, iPad…etc.)
Username: admin Password: 0000 (Four zeros) Default IP address: 192.168.1.23 Net Mask 255.255.255.0
4.1. Firmware
On the top right you can find the software firmware version and the processor utilization.
pg. 7
pg. 8
4.2. Source
This page contains input signal status, input Video Source and Audio Source selection. Users can change input video property, source and check input video information here. User can select on the top 1/2/3/4 icons to change the channel that willing to adjust.
4.2.1. Video Source (Local)
pg. 9
The user can change the video and audio sources here.
4.2.1. Video Source (Streaming)
The video source can be certain IP streams; HLS and RTSP are supported. Please check on other protocols. If the source is the encoder itself then for RTSP the format is;
rtsp://(Account):(Password)@(GSM 400 IP address):(RTSP port)/(Session name)
The example shown here is for an HLS stream In this case it is;
http://96.68.145.220/HLS/encoder1.m3u8.
This is one of our test streams, if you wish to test
this then contact us as we don’t keep it running all
the time.
pg. 10
4.2.2. Audio Source
In the audio source block, the user can select from Embedded audio, 3.5mm audio Line-in, Microphone input or Mixer.
4.2.3. Input Signal Status
In input information block, user can check signal status and signal format.
4.3. Encoder
Encoder page contains Main Encoder and Sub Encoder 2 parts, which allows user to change video and audio encode, this page also provides user to change sub streaming encoder.
pg. 11
4.3.1. Main Encoder/Sub Encoder
Resolution options: Same as input, 1920*1080, 1280*720 and 720*576, 720*480, 640*480, 320*240, and 160*120 resolutions
Framerate options: Same as input, 60, 50, 30, 25, 20, 15, 12.5, 10, 5, and 1.
Profile options: high, main and baseline.
Level options: 41, 40, 32, 31, 30, 22, 21, 20, 13, 12, 11, 10, and 1b.
pg. 12
Entropy: The GSM 400 supports both CAVLC and CABAC entropy encoding options. GOP: H264 group of pictures setting (from 255~1).
Video Bitrate (bps):
Audio Bitrate (bps): Audio bitrate select (from 256*1024~32*1024)
ColorRange: Select between Full Color or Limited Color.
pg. 13
4.4. Record
The record page allows user to change the video format that recorded to USB3.0 disk drive. On the top 1/2/3/4/PGM is the channel that desired to record; and the 2 block in the middle is the main/sub record format.
4.4.1. Main Record/Sub Record
Encoder source: Choices are; Main Encoder, Sub Encoder and disable selections. File name: The file name setting, this would be the file name recorded. Type: Decide needed file type; MP4, TS or AVI Duration: Choices are; Unlimitation, 60, 30, 5, and 1 minutes for user to set. Recording
will automatically stop when the time is up.
pg. 14
4.5. Streaming
This page contains the GSM 400 streaming settings; user can decide which encoder’s stream will send out and select streaming type here. On the top 1/2/3/4/PGM is the channel that desired steaming; and the 2 blocks in the middle are the main/sub streaming format.
4.5.1. Main Streaming/Sub Streaming
Encoder Source: User can select between main encoder and sub encoder. Streaming Type: Here are RTSP, RTMP, and TS streaming type GSM 400 available. RTSP port: RTSP server port RTSP HTTP Port: RTSP HTTP server port Account: RTSP account, setting this for other users to link with RTSP mode. Password: RTSP password, setting this for other users to link with RTSP mode. Session Name: RTSP Session name.
pg. 15
4.6. Snapshot
4.6.1. Snapshot
Capture: Select Enable or Disable File Name: Time and date codes are supported Type: Select the snapshot file format; BMP or JPEG
4.7. CG
The user can change on screen display content here; a Text label, place (Location-X, Location­Y) and color (Background Color, Foreground Color) or a Graphics file.
pg. 16
4.7.1. OSD Setting
OSD Layer: Each Input has up to 4 layers OSD Type: Each layer can be text or a graphics file Text: Text label for channel 1~4 and PGM
pg. 17
Location-X: OSD offset of X axis Location-Y: OSD offset of Y axis Background Color: OSD background color. Foreground Color: OSD foreground color.
4.8. PGM
pg. 18
This page contains the program (PGM) video output layout selections.
Full Screen
Mode
Full screen mode will display a single channel input
Picture in
Picture
Mode
For picture in picture mode, first channel select is the main channel, the second channel selection is the minor channel.
Picture by
Picture
Mode
Picture by picture mode will display all 4 channels in one screen, but there will be a main channel in the right. There is also a main channel selection in the bottom
pg. 19
4.9. Monitor
These 2 blocks are used to control the output modes, framerate and volume. For the HDMI model both outputs are HDMI, this is the SDI model’s output.
4.10. System
In the system page, user can set account /password, system reboot, format attached USB disk, check network status/setting and Firmware Update here.
pg. 20
4.10.1. Network Setting
DHCP: Enable/disable DHCP feature. When you disable DHCP, please provide necessary network parameters.
Static IP: Setting GSM 400 static IP. Subnet Mask: Setting GSM 400 subnet mask. Default Gateway: Setting GSM 400 default gateway. Primary DNS: Setting GSM 400 primary DNS.
4.10.2. Account and Password
Secondary DNS: Setting GSM 400 secondary DNS.
User can assign new account and password here.
4.10.3. Firmware Update
Press the Browse button to select the new firmware and Update button to update it,
during firmware update, please don’t turn off the power and wait until the upgrade progress completes.
4.10.4. Disk Format
The user can format a USB flash drive here.
pg. 21
4.10.5. System Control
Restore to default will erase all settings and back to original, and Reboot button will restart the GSM 400.
4.11. Status
User can check the GSM 400 status here (Including input signals, recording and streaming)
pg. 22
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use