Two power adapters.
Coverage Unit
Window Unit
In the package you will nd:
trouble shooting.
regarding installation and
other helpful information
for an installation video and
www.celfihelp.com
Visit us at
NEED HELP?
shooting steps included in this guide.
If you have any trouble during setup, please use the trouble
from your new Cel-Fi System.
guide, you can optimize the installation and get the very most
By spending just a few minutes using the instructions in this
a Window Unit and a Coverage Unit.
consists of placing and plugging in two components;
Setting up the system is extremely simple and
improvements in coverage as well as 3G data rates.
Quick Start Guide
This Cel-Fi system is designed to provide you with signicant
FIRS 2
-
CEL
Step 1
Find the spot with the best 3G coverage:
The rst step in setting up your Cel-Fi system is to
nd the spot in your home or oce that has the best
3G coverage. This is typically by a window, and if you
are in a multi-story building, upstairs windows are
usually better than downstairs windows.
indoor signal solution.
Congratulations on your new
Step 2
Plug in the Window Unit:
Take the Window Unit and one power supply out of
the box (both power supplies are the same, so grab
either one). Plug the Window Unit in, and check to
make sure that you can see at least 1 “Bar” on the
display in the center of the device. If you do not see
at least 1 bar, try a dierent location.
W I N D OW
U N I T
W I ND O W
U N IT
COVERAGE
UNIT
420N003-001-001-10R51
The system will start working normally when it cools down.
Make sure that the vents on the unit are not blocked. Move the unit to a cooler area.
(Use your cell phone to find the best 3G coverage).
Try moving the “Window Unit” to another room or area where you have coverage.
Try This
If problem persists return system for service.
2.
Try resetting the ”Coverage Unit” by unplugging it and then plugging it back in.
1.
Move the ”Coverage Unit” closer to the “Window Unit”.
1.
Move the ”Coverage Unit” further away from the “Window Unit”.
1.
rdware Error.
Ha
from the “Window Unit”
The ”Coverage Unit” is “Too Far”
to the “Window Unit”.
The ”Coverage Unit” is “Too Close”
“Window Unit” is overheating.
”Coverage Unit” is overheating.
No Signal on “Window Unit”.
Problem
E4
E3
E1
AG ES
Indicator
Red Status Indicator.
Red “Too Far” Indicator.
gment display shows a value of 0.
7 se
MESS
ERROR
Move away from WiFi devices.
2.
Wait for the display to stop cycling, this could take several minutes
1.
power supply is defective.
Try exchanging the power supplies with the “Window Unit” to see if the
3.
re power at the outlet?
2. Is the
1. Is the unit plugged in?
Try This
coverage. (Use your cell phone to find the best 3G coverage).
Try moving the “Window Unit” to another room or area where you have more
1.
If problem persists return system for service/replacement.
2.
Try resetting the “Window Unit” by unplugging it and then plugging it back in.
1.
See the “Coverage Unit” to determine what error code is being displayed.
1.
Wait for the status indicator to stop flashing, this could take several minutes.
1.
power supply is defective.
Try exchanging the power supplies with the “Coverage Unit” to see if the
3.
re power at the outlet?
2. Is the
1. Is the unit plugged in?
Try This
rmal to make a link.
longer than no
The ”Coverage Unit” is taking
There is no power.
Problem
receiving cell signal.
Not
rdware Error.
Ha
Error Code on ”Coverage Unit”.
to complete regulatory compliance.
The “Window Unit” unit is attempting
There is no power.
Problem
te.
gment display is cycling for more
gment lit on signal display and
re than a minute.
than a minu
7 se
No lights on ”Coverage Unit” display.
Indicator
status indicator on solid green.
No se
Status indicator is on solid red.
Status indicator is flashing red.
mo
Status indicator is flashing green for
No lights on “Window Unit” display.
Indicator
T
UNI
CO VE RA GE
T
UNI
WIND
OW
FIRS 2 Trouble Shooting
-
CEL
placement. Test two or three locations and for best results; try and get a 7, 8 or 9 on the display.
The number shown on the side of the display gives you an indication as to the quality of the
your home, so put the Coverage Unit as far away from the Window Unit as possible.
The farther away you place the coverage unit from the Window unit the better the coverage in
Optimize The Coverage Unit Placement
Step 5
“Window Unit”.
“Window Unit”.
moved closer to the
Unit” needs to be
that the “Coverage
This red icon indicates
TOO FAR
functioning normally.
“Coverage Unit” is
indicates that the
This green icon
GOOD
farther away from the
needs to be moved
the “Coverage Unit”
display indicates that
A zero on the numeric
TOO CLOSE
T
U N I
W I N D OW
move the Coverage Unit closer to the Window unit.
will illuminate indicating that you need to
the Window Unit. If this happens, a red icon
T
UNI
CO VE RA GE
far away that it cannot communicate with
It is possible to place the Coverage Unit so
indicating that the unit is working properly.
At this point you should see a green icon
this could take several minutes.
wait until the numeric display stops cycling,
have improved coverage. Plug the Coverage unit in and
Move to a location in your home where you need to
Place the Coverage Unit
Step 4
signal; the more bars the better.
couple of different spots to see if you can get better
the Cel-Fi system. Try moving the Window Unit to a
Unit make a significant difference in the operation of
The number of bars you can see on the Window
Optimize the Window Unit Placement
Step 3
Loading...