CEL-FI
QUICK START GUIDE
A41‐V32‐100
CEL-FI
QUICK START GUIDE
A41‐V32‐100
GO SMART ANTENNA
Cel‐Fi GO Smart Antenna is a high‐gain, low‐profile, magnetic‐mounted wideband cellular
antenna designed for mobile use on vehicles with the Cel‐Fi GO Smart Signal Booster.
Cel-Fi Go Smart Antenna
Magnetic Base
2
Server Antenna
3m Cable
Cel-Fi GO M
Instructions:
1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle.
The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi
GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach.
2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It
will not stick to aluminum.The antenna needs to be installed on a metallic surface
area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this
purpose well.
NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with
as much physical space between them as possible. This will allow the system to
configure to maximum gain without oscillation or feedback.
3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with
the Cel-Fi GO unit.
4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port.
The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server
Antenna Port. The product will not function if connected in any other manner.
NOTE: Use the supplied cable for best results, but any cable can be substituted as long
the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit.
5 Connect the Cel-Fi GO to the power supply.
1
3
4
5
Power
GO SMART ANTENNA
Cel‐Fi GO Smart Antenna is a high‐gain, low‐profile, magnetic‐mounted wideband cellular
antenna designed for mobile use on vehicles with the Cel‐Fi GO Smart Signal Booster.
Cel-Fi Go Smart Antenna
Magnetic Base
2
Server Antenna
3m Cable
Cel-Fi GO M
Instructions:
1 Place the Cel-Fi GO Smart Antenna in the desired location on the vehicle.
The Cel-Fi Go Smart Antenna comes with a 3m cable. The cable will connect the Cel-Fi
GO to the Smart Antenna. Make sure the Cel-Fi GO is within cable reach.
2 The magnetic base of the Cel-Fi GO Smart Antenna will stick to any ferrous metal. It
will not stick to aluminum.The antenna needs to be installed on a metallic surface
area (ground plane) of about 30 x 30mm. A vehicle's roof will typically serve this
purpose well.
NOTE: For best results, install the Cel‐Fi GO Smart Antenna and Server Antennas with
as much physical space between them as possible. This will allow the system to
configure to maximum gain without oscillation or feedback.
3 If the Cel-Fi GO needs to be installed, follow the instructions that were included with
the Cel-Fi GO unit.
4 Make sure to connect the Cel‐Fi GO Smart Antenna to the Cel-Fi GO unit’s Donor port.
The Cel-Fi GO is clearly marked with icons for a Donor Antenna Port and a Server
Antenna Port. The product will not function if connected in any other manner.
NOTE: Use the supplied cable for best results, but any cable can be substituted as long
the loss remains <2 dB from the Cel‐Fi GO Smart Antenna to the Cel-Fi GO M unit.
5 Connect the Cel-Fi GO to the power supply.
1
3
4
5
Power
Cel-Fi GO SMART ANTENNA Quick Start Guide
Cel-Fi GO SMART ANTENNA Quick Start Guide
6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart
Antenna with a Cel-Fi GO M.
NOTE: The Smart Antenna’s serial number can be found on the label on the bottom
of the unit.
6 Open the Cel-Fi WAVE app and follow the instructions for pairing a Cel-Fi GO Smart
Antenna with a Cel-Fi GO M.
NOTE: The Smart Antenna’s serial number can be found on the label on the bottom
of the unit.
Cel-Fi WAVE is available on both smartphones and
tablets from the following app stores.
Antenna Specifications:
ITEM
Frequency (MHz)
Dimensions (mm)
VSWR
Gain:
Gain:
Impedance (Ohm)
Polarization
Radiation pattern
Connector type
Ground plane
Mounting Type
Radome
Color
Operating Temp
IP
Copyright © 2018 by Nextivity, Inc. All rights reserved. The Nextivity and Cel-Fi logos are registered
trademarks of Nextivity Inc. All other trademarks or registered trademarks listed belong to their
respective owners.
qsg-antenna-go-active-eng_18-0316
SPECIFICATION
698 – 2700
120 x 180
3:1
698 - 960 MHz // 5 dBi
> 1 GHz // 6 dBi
50
Vertical
Omni‐directional (effective)
SMA‐M
Dependent
Magnetic
ASA UV Stable
Black
‐-20C - 55C
66
Cel-Fi WAVE is available on both smartphones and
tablets from the following app stores.
Antenna Specifications:
ITEM
Frequency (MHz)
Dimensions (mm)
VSWR
Gain:
Gain:
Impedance (Ohm)
Polarization
Radiation pattern
Connector type
Ground plane
Mounting Type
Radome
Color
Operating Temp
IP
Copyright © 2018 by Nextivity, Inc. All rights reserved. The Nextivity and Cel-Fi logos are registered
trademarks of Nextivity Inc. All other trademarks or registered trademarks listed belong to their
respective owners.
qsg-antenna-go-active-eng_18-0316
SPECIFICATION
698 – 2700
120 x 180
3:1
698 - 960 MHz // 5 dBi
> 1 GHz // 6 dBi
50
Vertical
Omni‐directional (effective)
SMA‐M
Dependent
Magnetic
ASA UV Stable
Black
‐-20C - 55C
66
Cel-Fi GO SMART ANTENNA Quick Start Guide Cel-Fi GO SMART ANTENNA Quick Start Guide
Loading...