p
r
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
POWER SUPPLY:
Connect the supplied adapter to the side of the unit in the slot marked “DC 5V IN”. Plug
the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty
inserting the plug, turn it over and reinsert it. If the unit will not be used for a long time,
disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions. To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric to
The exclamation point within an equilateral triangle is intended to alert the use
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
ersons.
Important Safety
Instructions
1
Important Safety
Instructions
NOTES
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a damp cloth.
7) Do not block any of the ventilation openings. Install in accordance with the
manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety.
When the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been dam aged i n an y way, such as p ow er-sup ply co rd o r p lug i s dam ag ed,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
2
Important Safety
Instructions
Warning
Failure to avoid the following potentially hazardous situations may result in injury or
property damage.
The unit is designed to provide you with route suggestions. It does not reflect road
closures or road conditions, traffic congestion, weather conditions, or other factors that
may affect safety or timing while driving.
Use the unit only as a navigational aid. Do not attempt to use the unit for any purpose
requiring precise measurement of direction, distance, location, or topography. This
product should not be used to determine ground proximity for aircraft navigation.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
The batteries (or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the
Global Positioning System (“GPS”) hardware, operating software or other aspects of this
product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety [Note-Consider referencing specific UL standard].
UL Certification does not cover the performance or reliability of the GPS hardware and
GPS operating software.
UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY GPS
RELATED FUNCTIONS OF THIS PRODUCT.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Cleaning of touch screen
If touch screen has fingerprints or dust on it, lightly wipe the touch screen with dry soft
cloth (or similar).
Never use record cleaning sprays, benzene, thinner, static electricity prevention liquids
or any other solvents to clean your touch screen
3
y
Features
Navigation Function
Navigation Function: The unit is designed to provide you with route suggestions. It supports voice
navigation.
Other Special Functions
SD Card and USB Input: The unit is
designed with SD card and USB ports and
can be connected to SD card or other USB
device for file loading.
Flash Storage: Built in Flash Storage can
store map data.
Power Adapter Switch: Automaticall
adapts to voltage requirements in U.S and
other countries.
Support file formats: Supports MP3
Format files playback.
4
Accessories
Accessories List
ITEM NAME QTY
Owner’s Manual 2
AC Adaptor 1
Car Adaptor 1
USB Cable 1
Windshield mount bracket 1
Mount cradle 1
Dashboard mount disk 1
Pouch 1
NOTE
Accessories and their part number are subject to modification without prior notice due to
improvements.
5
A
Important Safety Instructions
Features
View of Main Unit
System Connections
Power Supply Preparation
General Setup
Playing Music
Use of the Mount Accessories
Troubleshooting
Specifications
Contents
ccessories
……………………………………….……..1
……………………………………………...4
……………………………………………...5
……………………………………………...7
……………………………………….……..8
…………………………..……….…....….10
………………………………………..…..12
………………………………………..…..16
………………………………………....…18
………………………………………..…..19
………………………………………..…..20
6
1. LCD Screen
2. POWER button
Press to enter or exit the standby
mode.
3. Card Port
Insert the SD card into the port.
6. USB port
View of Main Unit
4. Headphone Jack
5. DC 5V Input Jack
Used to connect to the supplied car
adapter.
7. RESET button
Press to reset the system.
7
System Connections
Always ensure that the unit and any other external device connected to the unit are
switched off and unplugged from the power supply before you attempt to connect
the unit to any external device.
Connecting to PC
The unit is designed with a USB port that allows you to connect the unit to PC for map
updating. See the below figure for details:
System requirements:
-Windows 98SE, ME, 2000 and XP
(Driver required for Windows 98SE)
-DVD Rom Drive (for map upgrade purposes)
-Intel Pentium II 233 Mhz
-64 MB RAM
-50 MB available hard drive space
-Available serial port and/or USB Port
-256-color display adapter and monitor
(16 bit color required)
8
System Connections
Inserting SD Card
The unit is designed with SD Card jack that allows you to insert the SD card into the unit
as shown below:
Connecting to Headphones
Connect the headphones to the right side of the unit for private listening.
When headphone is connected, the speakers will automatically turn off.
Note: Excessively loud volume could damage your hearing. So turn down the volume
before you connect the headphones, and then raise the volume to comfortable level.
9
Power Supply
Preparation
Using the AC Adaptor
The unit is supplied with an AC adaptor for powering the unit and charging the battery.
1. Connect AC adaptor to the
right side of the unit in the jack
marked DC 5V IN, as shown on
the right.
2. Plug the two-prong end of the
power cord into a grounded
electrical outlet.
Note
Turn unit's power off before unplugging.
In the case of using the adaptor, the LCD screen will be brighter than with the
rechargeable battery.
Using of Car Adaptor
The unit is supplied with a Car Adaptor for powering the unit while in a vehicle.
Connect the car adaptor power plug
to the unit’s power jack and plug the
other end to the vehicle’s 5V
accessory/ cigarette socket, as
shown on the right figure.
Attention
Place the unit in a proper position for viewing.
Disconnect the unit from the car adaptor when starting the vehicle.
Your portable GPS comes with a built-in rechargeable battery. Please see details in the
following segment.
10
Power Supply
Preparation
About Rechargeable Battery
Your portable GPS comes with a built-in rechargeable battery. Charge the battery fully
before initial use. Charging time is normally about 3.5 hours. A fully charged battery
delivers about 3 hours of use.
Working conditions and precautions for the rechargeable battery
New batteries should be fully charged before initial use.
Battery should only be used when temperatures are between 14°-140°F(-10
℃). And it should be charged when temperatures are between 32°-113°F(0℃-45
℃)
Maintain well-ventilated conditions around the product to avoid overheating. Don’t
put the product on a bed, sofa or anything that may block ventilation to the product.
When the battery is weak, an indication menu will appear on the LCD screen and
about five minutes later, the unit will power off automatically.
℃-60
Charging the Battery Pack
The battery must be charged using the supplied adaptor.
11
General Setup
System Main Menu
When in navigation mode, tap button in the Menu screen. A confirmation message
appears asking if you want to exit the program now, as shown below.
In the confirmation screen, tap Yes and the system main menu appears.
In the system main menu, there are three items for selecting. Touch the corresponding
item to enter. Tap
menu. Tap
to enter navigation mode. Tap to enter the settings
to enter the Music player.
Settings Menu
Tap to enter the settings menu, the screen will display as below:
In the menu, tap
to return to the main menu.
12
LANGUAGE
Tap
selecting, as shown below:
Tap the
cancel.
BRIGHTNESS
Tap
adjusting, as shown below:
Tap the first group
After setting, tap
in the settings menu to enter LANGUAGE settings menu for language
buttons to select language. Then tap to confirm or tap to
in the settings menu to enter BRI GHTNESS settings menu for brightness
buttons to adjust the brightness level.
to confirm or tap to cancel.
General Setup
13
General Setup
DATE & TIME
Tap
the current time zone, as shown below:
Tap the
Date group to change the corresponding date and tap the
to change the corresponding time. Tap
POWER
Tap
shown below:
The power menu will display the current battery status. Tap
in the settings menu to ent er DATE & TIME settings menu for changing to
buttons to select the proper Time Zone. Tap the buttons of
to return.
in the settings menu to enter POWER menu for the current battery status, as
buttons of Time group
to return.
14
CALIBRATE
Tap
of the unit, the screen will display as below:
Tap the center of “+” as it moves around the screen. If you touch the center of “+” every
time, it will disappear and tap the screen to return to the settings menu.
Note: If “+” doesn’t disappear, you should calibrate again.
MASTER VOLUME
Tap
adjusting, as shown below:
Tap the
Note: there are two levels of volume control: one is the master control in the ge neral
set-up; the secondary volume control is in the navigation or mp3.
in the settings menu to enter CALIBRATE menu for calibrating the sensitivity
in the settings menu to enter VOLUME settings menu for master volume
buttons to adjust the master volume. Then tap to confirm or tap
to cancel.
General Setup
15
Playing Music
The unit is designed with SD card slot. You can insert the SD card with MP3 files. It only
supports MP3 format files playback.
Note: Do not store MP3 format files in the Fla sh storage, for the flash storage is
used to store map data, any attempt to open the Flash storage may result i n the
map data missing and lost.
Warning: For your own safety, do not use the earphones when driving.
Take the following steps to play:
Loading MP3 format files
1. Insert the SD card with MP3 files.
2. Turn on the unit.
A note regarding the MP3 function
The unit has the ability to play your favorite MP3 music files. This is accomplished by
using the unit’s SD card slot, located on the right side.
MP3 files should previously reside on the users SD card.
MP3 files can be imported to the users SD card on a PC, using a variety of
programs such as Windows Media Player.
This process should be performed independent of the navigation unit.
Do not attempt to use the unit to read and burn MP3 files from an external source.
Playing Music.
In the main menu, tap to enter the MP3 main screen, as shown below:
In the MP3 player, tap
in the top left corner to exit.
16
In the menu, tap the MENU button to enter the MP3 play list menu, as shown below:
When you open the play list, the system will look for audio files on its SD memory card
and create a play list automatically. If the play list consists of more than one screen, tap
the up arrow
In the play list, double tap the songs to start playback.
Tap ; when the button changes to orange, the player will repeat all the songs in the
play list.
Tap
randomly.
Tap
for the previous page and the down arrow for the next page.
; when the button changes to orange, the player will play the songs in the list
to return to the MP3 main screen.
Playing Music
On the playback screen as shown right, the MP3 player
has standard playback features:
button to start playing the songs in the play list.
Tap
to stop the playback.
Tap
to pause the playback, and then tap to resume the playback.
Tap
Tap
to back to the previous song; tap to skip to the next song.
Use
Tap
to adjust the volume of the speaker.
to select the desired playback starting time.
17
Use of the Mount
When using the unit in vehicle, you can use the supplied mount accessories (mount
bracket, mount cradle and dashboard mount disk) to mount the unit in the vehicle. Take
the following steps to operate:
1. See Fig. 1. Push the mount cradle to mount bracket.
2. See Fig. 2. Fix the unit on mount cradle and bracket.
3. See Fig. 3. Lift the suction fastener, and place the unit on the desired location, then
If you want to mount the unit to the dashboard, you can use the adhesive disk:
Accessories
press down fastener for immobility. Rotate the knob to adjust the unit to proper
position.
1) Choose a clean, dry spot on your dashboard
2) Peel off protection liner from the back of the disk.
3) Attach the disk to your dashboard.
4) Mount the bracket to the adhesive disk.
18
A
Take steps described in the tables below to solve simple problems before contacting customer
service.
If you suspect something wrong with this unit, immediately turn the power off and disconnect
the power connector from the unit. Never try to repair the unit yourself because it is dangerous
to do so.
PROBLEM
There is no sound
There is no picture.
POSSIBLE CAUSE
The volume may be turned
down.
The brightness may be
turned down.
Other possibilities:
Static or o ther ex ternal in terfe rence may caus e the unit f uncti on abno rmally. In ord er to rec ov er
normal status, please unplug the power supply cord and then plug it into the outlet again to
reset the unit. If the problems still exist, please cut off the power supply and consult your
service center or the qualified technician.
Troubleshooting
POSSIBLE SOLUTION
Turn up the volume.
djust the brightness of the
LCD.
19
Specifications
TFT screen size 3.5 inches
Frequency Response 20Hz～20kHz
Audio Signal-to-noise Rate ≥65dB
Audio distortion or noise ≤－20dB (1kHz)
Channel Separation ≥70dB (1kHz)
Dynamic Range ≥80dB (1kHz)
Power AC 100-240V ～ 50/60Hz; DC 5V
Power Consumption < 8W
Dimensions 100mmX76mmX22mm (L*W*D)
Weight About 0.25kg
DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
20
© 2008 Nextar (Hong Kong) Limited. Nextar is a trademark and service mark of Nextar
(Hong Kong) Limited. All other brand names, trademarks and service marks are property
of their owners.
Nextar may find it necessary to modify, amend or otherwise change or update this
manual.
We may reserve the right to do this at any time, without any prior notice.
All specifications and features are subject to change without notice.
www.nextar.com
Or write us at:
Nextar Inc.
1661 Fairplex Dr.
La Verne, CA91750
USA
26
Loading...