Tools Needed
Helpline
If you have any problems with this product or
require any replacement fittings please contact
Customer Services Tel: 0844 844 8999
• All assembly fixings should always be tightened properly and periodically check all fixings and tighten if
necessary.
• Regular cleaning is essential to avoid build up of these products on the surface.
• Avoid exposure to direct or prolonged periods of sunlight and position away from direct heat sources
• Care should be taken to avoid spilling anything on the upholstery. If a spillage occurs act promptly and
soak up any liquids by blotting with a clean absorbent cloth. Never rub to remove stains. Never use a wet
• If a spillage does occur, blot any liquids immediately with a clean, dry absorbent cloth and allow to dry
• For more stubborn stains a professional upholstery cleaner should be consulted.
• Clean periodically in situ using a professional cleaning company.
• Made with fabric covering.
• Fabric content: 64% polyester, 36% viscose.
• Made in China.
CARE INSTRUCTIONS
• Hair products such as hairsprays, oils and gels may affect the finish. Avoid prolonged contact with such
• Carefully check that you have all the parts before beginning assembly.
• Keep fittings out of children’s reach and keep children well away from construction area.
• We suggest you retain these instructions for future reference.
• A minimum of 2 persons is required to assemble this product.
• We recommend that the packaging is used to protect the surfaces during assembly.
PRODUCT INFORMATION
ASSEMBLY INSTRUCTIONS.
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
Regrettably self assembly items cannot be returned once assembly is part or fully completed unless the
item is found to be faulty. Should you need to return the unassembled product, please repack in the
IMPORTANT
• We suggest you spend a short time reading through this leaflet and then follow the simple step by step
PORTOFINO MINK BED
Page 1 of 5
1. Attach 4 x wooden legs 6 to headboard 1 and
footboard 2 with 4 x bolts (A2), 4 x flat washers
(D) and 4 x spring washers (C), tighten using
1. Attach 2 x side rails 3 to headboard 1 and
footboard 2 with 8 x bolts (A1), 4 x flat washers
(D) and 4 x spring washers (C), tighten using
Allen Key (H) taking care not to over tighten
FITTINGS
PARTS
STEP ONE
STEP TWO
2
1
3
1
2
3
Page 2 of 5
1. Attach 2 x centre support legs 5 to centre rail
4 with 4 x bolts (B), 4 x washers (D) and 4 x nuts
(E), tighten using a screwdriver.
2. Attach centre rail 4 to headboard 1 and
footboard 2 with 4 x bolts (A1), 4 x spring
washers (C) and 4 x washers (D), tighten using
Allen key (H). If required re-adjust the bolts
1. Insert all slats 7 through the gaps in 2 x slat
2. Attach slat caps (F) onto each slat down one
side on each of the slat assemblies.
1. Attach double sided slat caps onto the other
ends of each slat assembly and connect
together to form the bed base.
NOTE: Ensure the curve of the slats are facing
upwards.
STEP FOUR
STEP FIVE
STEP THREE
Page 3 of 5
1. Position the assembled bed base to side rails
3 and centre rail 4 and firmly insert the pins of
the slat caps (F&G) into the holes in each rail.
2. Repeat with all slats to attach the bed base.
IMPORTANT:
Once the feet have been assembled and
attached, they should be adjusted to ensure they
do not touch the floor (5mm above the floor), to
allow for movement once the mattress is placed
It is important to note that when moving the bed
that it is not dragged into its new position to
prevent the possibility of these feet being
twisted or angled to one side, which could lead
to the collapse of the centre of the bed.
To move the bed, remove the mattress and lift
the bed into the new position to avoid damage.
Ensure the feet are at 90° to the floor before
STEP SIX
STEP SEVEN
Page 4 of 5
Next Retail Ltd, Desford Road, Leicester, LE19 4AT
Page 5 of 5
Loading...