Next NAVIGATOR 612 User Manual

N
ext
PROGRAMMABLE DMX CONTROLLER
USER’S MANUAL
GB
Sets of the equipment
Unpacking of the equipment
Acessories issued with the equipment and relative documentation
Description of the rear panel and installation
Description of the rear panel
DMX 512 output connection
2.3
Input connection for power supply
2.4
Connection of the ballast to the electric system
Use of the equipment - modes of operation
PROGRAM
mode
SCENE
mode
MAN + PROGRAM
mode
MAN + SCENE
mode
Description of the front panel
Description of the front panel
Use of the equipment - main functions
Adjustment of the
RATE
speed
Adjustment of the
SPEED
speed
Adjustment of the X and Y channels through the Joystick
Adjustment of the
IRIS - COLOUR - GOBO - SHUTTER
channels
MUSIC
function
BLK
function
Use of the equipment - secondary functions
MEM
function
COPY
function
LENGTH
function
REPEAT
function
Exemple of working - creation of a program
Creation of a program
We congratulate you on your purchase of NAVIGATOR 612. Before proceeding of the use of this product it should be necessary to read carefully the following user’s manual to install it correctly and to make the most of its potentialities.
INDEX
Verify the contens of the packing. If one of the following parts of the packing is missing or damaged, please, contact your dealer immediately.
A) User’s manual B) AN-612 Ballast
Open the box; take the ballast and the documentation out. Take the equipment out of the box as shown in the picture below.
1.1 UNPACKING OF THE EQUIPMENT
1.2 ACCESSORIES ISSUED WITH THE EQUIPMENT AND RELATIVE DOCUMENTATION
AB
AUDIO IN
(0 dB)
POWER INPUT 12 VDC - 2 W
DMX 512
OUTPUT
+VDC
COMMON
12
3
1
1 = COMMON 2 =DATA
-
3 =DATA +
4
= n.c.
5
= n.c.
5
3
42
15
3
42
PUSH
3
2.1 DESCRIPTION OF THE REAR PANEL AND INSTALLATION
1
Standard DMX 512 signal OUTPUT with a 5-pin cannon connector.
2
0 dB audio signal INPUT with a mono/stereo jack connector.
3
12 Vdc power INPUT with a 3-pin cannon connector.
2.2 DMX 512 OUTPUT CONNECTION
Make sure you are using a shielded twisted cables suitable for the transmission of the DMX 512 signal with connectors of good quality and connection as shown on the side of the connector.
Plug the 5-pin cannon connector coming from the projectors completly in the DMX 512 output
Use the “push” safety hook to disconnect it and than extract it gently.
ATTENTION: the shielded part of the cable must never be connected to the ground of the electrical system as this could cause faults during the working of the controller.
The “start” channel of the controller is channel n°1, for other DMX address you can follow the tabel below.
SCANNER N° 1 SCANNER N° 2 SCANNER N° 3 SCANNER N° 4 SCANNER N° 5 SCANNER N° 6
DMX address: 1 DMX address: 7 DMX address: 13 DMX address: 19 DMX address: 25 DMX address: 31
SCANNER N° 7 SCANNER N° 8 SCANNER N° 9 SCANNER N° 10 SCANNER N° 11 SCANNER N° 12
DMX address: 37 DMX address: 43 DMX address: 49 DMX address: 55 DMX address: 61 DMX address: 67
1
1
2
2.3 INPUT CONNECTION FOR POWER SUPPLY
2.4 CONNECTION OF THE BALLAST TO THE ELECTRIC SYSTEM
Plug the 3-pin cannon connector of the ballast completly in the power input
Use the “push” safety hook to disconnect it and extract it gently.
ATTENTION: do not use ballast different from the one supplied, it could cause serious damages at the internal circuitation.
Do not connect the 3-pin cannon connector in other appliances, it has been studied to be used only in this controller.
3
MAKE SURE THAT VOLTAGE AND POWER FREQUENCY CORRESPOND TO WHAT IS REPORTED ON THE BALLAST PLATE.
The supplied ballast has a plug, therefore you should only plug it in the socket. Press
POW
key to verify the correct installation.
If pressing the
POW
key no one led light up, please check if there is tension in the electric socket or check the connection between ballast-controller and ballast-electric socket.
If the problem persist, please consult your dealer.
Pressing PROG key the
PROGRAM
function is activated
(Fig.1) The red led of PROG key will light up to indicate the activation
of this function.
This function allows to activate a program or a range of programs
Press 1÷12 keys to activate/deactivate the programs which will be performed in succession. All selected programs have a lighted up led, while the active program has a flashing led.
N.B. Each program is repeated for a number of times established through the
REPEAT
function (see par. 6.4)
The speed of change between the scenes can be controlled by
RATE and
RATE
keys (see par.
5.1).
The relation between the movement of the scanners and the pause between scenes is controlled by SPEED ▲ and SPEED keys (see par. 5.2).
When the maximum or minimum speed is reached the led of the SHIFT key flashes.
Fig. 1
3.1 PROGRAM MODE
PROG
Pressing SCENE key the
SCENE
function is activated (Fig.2)
The red led of SCENE key will light up to indicate the activation of this function.
When you pass from
PROGRAM
mode to
SCENE
mode, the
scene active in that moment is selected. Press any 1÷12 keys to activate/deactivate the scene.
This function allows to see one of the 12 scenes of the program in action. N.B. If no programs are selected the SCENE function is not active.
The speed of change between the scenes can be controlled by RATE and RATE (see par. 5.1). When the maximum or minimum speed is reached the led of the SHIFT key flashes.
N.B. In this function SPEED and SPEED keys are not activated
Fig. 2
3.2 SCENE MODE
SCENE
When
PROGRAM
function is working, pressing MAN (Fig.3)
key the
MAN+PROGRAM
function is activated.
The red led on PROG and MAN keys will light up to indicate the activation of this function.
Pressing MAN key once more you come back in
PROG
mode.
This function allows to activate manually one or more scanners while the not selected ones go on performing the PROGRAM function.
Press 1÷12 keys to activate/deactivate the scanners manually controlled. The selected scanners (with ligthed up led) do not follow anymore the
program, but are manually controlled through the joystick, the selection of the channel and the slider.
Once it has been deactivated, the scanner performs again the working program.
Fig. 3
3.3 MAN+PROGRAM MODE
MAN
When
SCENE
function is working, pressing MAN key
(fig. 4) the
MAN+SCENE
function is activated.
The red led of SCENE and MAN keys will light up to indicate the activation of this function.
Pressing MAN key once more you can come back to the
SCENE
mode.
This function allows to activate manually one or more scanners to create or to modify a scene.
Pressing one of the
1÷12
keys the scanner manually controlled is activated.
To select more scanners press in sequence
1÷12
keys very quickly. The selected scanners (with lighted up led) can be manually controlled using the joystick, the channel selection and the slider.
Once another scanner has been selected, the previous one keeps all made sets.
Fig. 4
3.4 MAN+SCENE MODE
MAN
4.1 DESCRIPTION OF THE FRONT PANEL
SHIFT
POWER
RATESPEED
1
MEM
5
COP
9
F1
F2
MUSIC
MAN
PROG
SCENE
1
1
5 6
7 8
2
3
4
To activate /deactivate the controller storing all the data.
2
To activate the PROGRAM mode.
3
To activate the SCENE mode.
4
To activate the PROG+MAN / SCENE+MAN function.
5
To activate the MUSIC function for the change of the scene to the beat of the music.
6
To activate the SHIFT function and select the second function of 1/12 keys.
7
To increase / reduce the SPEED value.
8
To increase / reduce the RATE value.
9
To select a program / scene / scanner depending on the working function.
CH.
SEL.
0
255
CHANNEL
IRIS
COLOUR
GOBO
SHUTTER
3
LENGTH
7
4
8
F3
12
F4
REPEAT
10 12 1311
9
9
10
To select the channel on which the slider should operate.
11
It shows the channel on which the slider is operating.
12
Slider: it changes the value from 0 to 255 of the selected channel.
13
Joystick: it allows an easy positioning of the scanners.
RATE
The adjustment of the RATE is activated only in
PROG
and
SCENE
function. The two settings of the value are indipendent as passing from one mode to the other you find the same previous set value.
The RATE value is simply the time that the scene takes to arrive at the end, therefore it is also the speed of the change between the scenes.
Using the
RATE
key (Fig.5) the speed increases, i.e. the
scene takes less time to arrive at the end position, while using the
RATE
key (Fig.5) the speed reduces up to a value
of 30 seconds to end the scene. When the maximum and minimum speed is reached the led
on the SHIFT key flashes.
The SPEED value is the ratio between the time of the scanner’s movement and the total length of the scene.
The SPEED value are 10: from 10% to100%. Using the
SPEED
key (Fig.6) the speed increases and the
time of pause, too, while using the
SPEED
key (Fig.6) the
speed reduces and the movement becomes continuous, without pauses.
For instance, if you set a RATE of 30 seconds and the SPEED has the minimum value, the scene has a length of 30 seconds and the movement of the mirror has a length of 30 seconds,too. If you set the previous RATE value but you increase the SPEED value up to 50%, the length of the scene is always 30 seconds instead the movement of the mirror has a lenght of 15 seconds (as the speed is doubled in comparison with the previous one) and a pause of 15 seconds.
When the maximum and minimum speed are reached the led on the SHIFT key flashes.
Fig. 5
5.1 ADJUSTMENT OF THE RATE SPEED
SPEED
The SPEED adjustment is activated only in PROG function, while it is deactivated in SCENE and MUSIC function.
Fig. 6
5.2 ADJUSTMENT OF THE SPEED
Fig. 7
Fig. 8 Fig. 9
Using the joystick the X and Y channels of the scanner’s mirror can be adjusted (Fig.7). The type used is the one with the return in the centre which allows an easy and exact positioning thanks to the sophisticated software of management, too. The movement is a proportional type, i.e. if you keep the joystick in central position the mirror keeps still; whereas the more you move it away from the centre the more the movement of mirror increases. To make a movement of a step it will be enough to give some small strokes to the joystick in the desired direction.
5.3 ADJUSTMENT OF THE X AND Y CHANNELS THROUGH THE JOYSTICK
The adjustment of the 4 channels is made with only one slider (Fig.8). The value of the slider is connected with the channel which is selected through the CH.SEL. key and it is indicated by the leds on the key (Fig.9). To change the channel on which the slider is working press one or more times the CH.SEL. key till the led of the desired channel lights up.
N.B. Every time you change channel the previous value of each channel is not modified till you do not move the slider.
5.4
ADJUSTMENT OF THE
IRIS - COLOUR - GOBO - SHUTTER
CHANNELS
CH.
SEL.
0
255
CHANNEL
IRIS
COLOUR
GOBO
SHUTTER
TTHHEE CCOONNTTRROOLLLLEERR WWOORRKK WWIITTHH PPAANN AANNDD TTIILLTT OONN TTHHEE CCHHAANNNNEELLSS 55 AANNDD 66 TToo mmooddiiffyy tthhee aassssiiggnnmmeenntt ooff tthhee ppaann aanndd ttiilltt oonn tthhee cchhaannnneellss 11 aanndd 22 ppeerrffoorrmm tthhiiss pprroocceedduurree::
-Hold pressed the 11key and
turn on the controller through
PPoowweerr
key at the same time.
Now the Joystick work with the channels
11 aanndd 22
.
TToo mmooddiiffyy tthhee aassssiiggnnmmeenntt ooff tthhee ppaann aanndd ttiilltt oonn tthhee cchhaannnneellss 55 aanndd 66 ppeerrffoorrmm tthhiiss pprroocceedduurree::
-Hold pressed the 55key and
turn on the controller through
PPoowweerr
key at the same time
..
Now the Joystick work with the channels
55 aanndd 66
.
Pressing the MUSIC key (Fig.10) the
MUSIC
function is activated.
This function can be activated only during the PROGRAM and MAN+PROGRAM mode.
The green led on the key lights up to indicate the starting of this function.
This function performs the program to the rhythm of the music, synchronising the change of the scene with the bass beats.
Using this function the change of the scenes occurs only when the musical sensor receives the audio signal from the rear audio input or from the built-in microphone. (If to the rear input you connect a jack the built-in microphone is deactivated).
The speed of the change between the scenes is controlled by the
RATE
and the
RATE
keys: when the max or mi speed is reached the led on the SHIFT key flashes.
Usually, during the MUSIC function, the speed of the change between the scenes should be not so low otherwise the movement of the scanner will be very slow. The internal music sensor has an automatic gain adjustment which allows to have a signal level good for the controller’s working. The input music signal is a 0dB mono/stereo so it could be taken from sound sources like Mixer, CD, Dat etc.
N.B. In this function the
SPEED
and the
SPEED
keys are deactivated.
Only one channel of the jack stereo connector placed on the rear of the controller is connected to the music sensor.
IT IS ABSOLUTELY FORBIDDEN TO CONNECT TO THIS INPUT ANY POWER SIGNALS FOR ACOUSTIC SPEAKER COMING FROM AMPLIFIED MIXER OR AMPLIFIER!!
Fig. 10
5.5 MUSIC FUNCTION
MUSIC
This function can be activated only during the PROGRAM and MAN+PROGRAM mode.
To activate the BLK function you have to activate the second function of the keys pressing once the SHIFT key (Fig.11).
(a yellow led on the SHIFT key lights up). Than press
12/BLK
key (Fig.12).
Now, the led on the
12/BLK
key is flashing and all the
function of the controller are off. Only pressing again the
12/BLK
key the controller return to
it’s normal functions.
Fig. 11
Fig. 12
SHIFT
This function reset the color and the gobo channels in all the scanners.
5.6 BLK function (blackout)
12
BLK
To activate the
MEM
function you have to activate the second function of the keys pressing once the SHIFT key (Fig.11). (a yellow led on the SHIFT key lights up).
If the led on the SHIFT key does not light up, the
MEM
function cannot be activated as no scene has been selected previously.
Than press
1/MEM
key (Fig.12).
Now, the settings of the channels and the X and Y position of all scanners are stored in a permanent way in the selected scene of the active program (see par. 7.1).
If all the operations have been done correctly, the mode of working pass from
MAN
mode to
SCENE
mode so that any
other scene can be selected, created or modified.
To activate the COPY function you have to activate the second function of the keys pressing once the SHIFT key (Fig.13). (a yellow led on the SHIFT key lights up).
If the led on the SHIFT key does not light up, the COPY function cannot be activated as no scene has been selected previously.
Than press
2/COPY
key (Fig.14).
Now, the led of the active scene is flashing; press any 1÷12 keys to select the scene of destination.
Pressing a different key the copy function is cancelled. If all the operations have been done correctly, the active
scene becomes now the scene of destination.
This function stores in a scene the present situation of the scanners.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
THIS FUNCTION IS AVAILABLE ONLY IN
MAN
MODE
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
6.1 MEM FUNCTION
Fig. 13
Fig. 14
SHIFT
This function allows to copy the present active scene in another one.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
THIS FUNCTION IS AVAILABLE ONLY IN
SCENE
MODE
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
6.2 COPY FUNCTION
2
COPY
Fig. 11
Fig. 12
SHIFT
1
MEM
Fig. 15
Fig. 16
SHIFT
3
LENGTH
To activate the LENGTH function you have to activate the second function of the keys pressing
once
the SHIFT key (Fig.15).
(a yellow led on the SHIFT key lights up).
If the led on the SHIFT key does not light up, the
LENGTH
function cannot be activated as no program has been selected previously.
Than press
3/LENGTH
key (Fig.16).
Now, the led of the the selected length is flashing; press any 1÷12 keys to select a new length of the program.
Pressing a different key the operation is cancelled.
This function allows to choose the length of the active program, or rather the last performed scene of the program.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
THIS FUNCTION IS AVAILABLE ONLY IN
PROG
MODE
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
6.3 LENGTH FUNCTION
Fig. 17
Fig. 18
SHIFT
4
REPEAT
To activate the
REPEAT
function you have to activate the second
function of the keys pressing
once
the SHIFT key (Fig.17).
(a yellow led on the SHIFT key lights up).
If the led on the SHIFT key does not light up, the
REPEAT
function cannot be activated as no program has been selected previously.
Than press
4/REPEAT
key (Fig.18).
Now, the led corresponding with the selected number of repetitions is flashing; press any 1÷12 keys to select a new value.
Pressing a different key the operation is cancelled.
This function allows to select the number of repetitions for each program.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
THIS FUNCTION IS AVAILABLE ONLY IN
PROG
MODE
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
6.4 REPEAT FUNCTION
A program is a range of scenes (max 12) performed in succession. To create (or to modify) a program follow all steps listed below:
1) If the controller is switched off, switch it on pressing POW key.
2) Press PROG key to activate the
PROGRAM
function.
(the red led on the same key will light up).
3) Using 1÷12 keys select only the program that you want to modify.
(only one program is flashing).
4) Press SCENE key to activate the
SCENE
function.
(the red led on the same key will light up).
5) Using 1÷12 keys select the scene that you want to modify.
6) Press MAN key to activate the
MAN+SCENE
function.
(the red leds on the MAN and SCENE keys will light up).
7) Using 1÷12 keys select one or more scanners and modify the position
with the joystick and the sets of the channels with the CH.SEL. key and the slider.
8) Once the scanners have been selected and the scene has been completed,
it can be stored using the
MEM
function: press SHIFT key and than
1/MEM key (see par. 6.1).
9) Now the controller is again in the
SCENE
function in order that you can
select another scene or copy the scene already done in another one (see par. 6.2).
10) Once the creation of the scenes has been finished press PROG key to
come back to the
PROGRAM
function.
(the red led on the same key will ligth up).
11) Finally, you should set the length of the program using the
LENGTH
function: press once SHIFT key than the 3/LENGTH key followed by
the number of the last stored scene (see par. 6.3).
The program is finished; to create or modify others repeat again all the above steps.
7.1 EXAMPLE OF WORKING - CREATION OF A PROGRAM
All rights reserved. No parts of this document can be copied, photocopied or reproduced without the prior written permission of the CODEM MUSIC s.r.l.
No responibility is taken for possible inaccuracies or mistakes. The CODEM MUSIC s.r.l. reserves the right to make any alterations or aesthetics changes of this
product that seem necessary at any time and for whatever reason. The CODEM MUSIC s.r.l. takes no responsibility for the use or for the application of this product.
TECHNICAL FEATURES OF NAVIGATOR 612
Technical features: programming
Number of scanners controlled separately: 12 Number of channels for each scanner: 6 (4ch. + Y + X) Number of stored programs: 12 Number of scenes for each program: 12 Total number of scenes: 144 (12 programs x 12 scenes) Positioning way of the mirror: through a proportional Joystick with return.
Technical features: output signal
Kind of output signal: DMX512/ 1990 Output connector: 5-pin cannon connector Max number of scanners connected to the DMX output: 32 Number of DMX channels: 72 (6 ch. x 12 scanners)
Technical features: storage of program
Kind of storage / size: EEPROM / 128 Kbit Length of data maintenance without power supply: > 40 years Number of entries cycles: >100.000
Technical features: storage of settings
Kind of storage / size:
EEPROM / 2 Kbit
Length of data maintenance without power supply: > 40 years Number of entries cycles: >
10.000.000
Climatic condition for the use
Humidity: 35% ÷80% Temperature: 5 ÷50 °C
Power supply
Voltage/current: 12 Vdc / 240 mA
Technical fetures: audio input
Source: Inside through a built-in microphone / outside through a stereo jack Sensitivity / input impedance: 0 dB (775 mV) / 50 Kohm Kind of level adjustment: Automatic
Dimensions and weight
Dimension (W x L x H) / Weight: 482 x 88 x 40 mm (2U rack) / 1,5 Kg.
CODEM MUSIC S.r.l. - Via Del Vallo, 110 - 61100 PESARO - ITALY
Tel. +39 0721 204357- Fax +39 0721 203554
hhttttpp::////wwwwww..ccooddeemmmmuussiicc..ccoomm -- EE--mmaaiill:: iinnffoo@@ccooddeemmmmuussiicc..ccoomm
Loading...