Nexcom TPPC 2210, TPPC 2210T, TPPD 2200 User Manual

NEXCOM International Co., Ltd.

Published May 2018

www.nexcom.com

Intelligent Platform & Services Business Unit

Passenger Information Panel PC TPPC 2210 and TPPD 2200 Series

User Manual

ii

TPPC 2210 and TPPD 2200 Series User Manual

Content

Contents

Preface

Copyright ............................................................................................. iv

Disclaimer .............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements ........................................................ iv

Declaration of Conformity ...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................viii

Installation Recommendations ...............................................................viii

Safety Precautions .................................................................................. ix

Technical Support and Assistance ............................................................ x

Conventions Used in this Manual ............................................................ x

Global Service Contact Information ........................................................ xi

Package Contents .................................................................................xiii

Ordering Information ............................................................................xiv

Chapter 1: Product Introduction

TPPC 2210 ..............................................................................................1

Overview .............................................................................................1

Key Features ........................................................................................1

TPPC 2210T ............................................................................................2

Overview .............................................................................................2

Key Features ........................................................................................2

TPPD 2200 ..............................................................................................3

Overview .............................................................................................3

Key Features ........................................................................................3

Hardware Specifications ..........................................................................4

Knowing Your TPPC 2210/TPPC 2210T ...................................................6

Rear Bottom ........................................................................................6

Knowing Your TPPD 2200 ....................................................................... 6

Rear Bottom ........................................................................................6

Rear and VESA Mount .........................................................................7

Mechanical Dimensions ...........................................................................8

TPPC 2210 ..........................................................................................8

TPPD 2200 ..........................................................................................9

With VESA Mount ............................................................................. 10

Chapter 2: Jumpers and Connectors

Before You Begin ..................................................................................11

Precautions ..........................................................................................11

Jumper Settings ....................................................................................12

TPPC 2210 and TPPD 2200 System Boards ............................................13

Location of the Connectors for TPPC 2210 Motherboard ......................13

Location of the Jumpers for TPPC 2210 Motherboard ...........................15

Motherboard .....................................................................................16

Jumper Table ..................................................................................16

Connector Table .............................................................................16

Header Table ..................................................................................16

Jumpers ................................................................................................17

LVDS PVCC 3.3V/5V/12V Function Select ........................................... 17

Inverter VCC 5V/12V Select ...............................................................17

COM4 Header Pin 9 Function Select ..................................................18

COM3 Header Pin 9 Function Select ..................................................18

iii

TPPC 2210 and TPPD 2200 Series User Manual

Content

COM2 Header Pin 9 Function Select ..................................................19

COM1 Header Pin 9 Function Select ..................................................19

Clear CMOS ......................................................................................20

Case Open Message Display Function Select ......................................20

AT Mode Function Select ...................................................................21

Security Measure Function Select .......................................................21

Connector Pin Definitions .....................................................................22

Rear I/O Connectors ..........................................................................22

SATA II Connector .............................................................................22

SATA Power Connector .....................................................................22

CPU Fan Connector ...........................................................................23

LVDS Inverter Connector .................................................................... 23

Line-out and Mic-in Header ...............................................................24

SPDIF Out Header ..............................................................................24

Serial Port Headers ............................................................................25

GPIO Header .....................................................................................25

USB 2.0 Port Header ..........................................................................26

SMBus Header ...................................................................................26

PS/2 Keyboard & Mouse Header ........................................................27

Front Panel Header ............................................................................27

LAN Activity LED Headers ..................................................................28

24-bit Dual Channel LVDS Header......................................................28

Location of the Jumpers and Connectors for TPPC 2210 Power Board ...29

Power Board ......................................................................................30

Jumper and Connector Table ..........................................................30

Location of the Jumpers and Connectors for TPPC 2210 TX Board ........31

TX Board ...........................................................................................32

Connector Table .............................................................................32

Location of the Jumpers and Connectors for TPPD 2200 RX Board ........33

RX Board ...........................................................................................35

Connector Table .............................................................................35

Location of the Jumpers and Connectors for TPPD 2200 AD Board .......36

Jumpers ................................................................................................37

Backlight Adjust ................................................................................37

Panel VCC Select ...............................................................................37

Panel Number Select ..........................................................................38

Connector Pin Definitions .....................................................................39

DC Power Input (12V ~ 24V) .............................................................39

DC Power Output (5V) .......................................................................39

Backlight Power and Signal Output ....................................................40

LVDS Connector ................................................................................40

Keypad Input .....................................................................................41

VGA Connector .................................................................................41

DVI Connector ...................................................................................42

Chapter 3: System Setup

Removing the Chassis Cover ................................................................43

Installing a SO-DIMM Memory Module .................................................45

Installing a Mini PCIe Module (Optional) ................................................46

Installing VESA Mount (Optional) ..........................................................49

Chapter 4: BIOS Setup

About BIOS Setup .................................................................................51

When to Configure the BIOS .................................................................51

Default Configuration ...........................................................................52

Entering Setup ......................................................................................52

Legends ................................................................................................52

BIOS Setup Utility ..................................................................................54

Main .................................................................................................54

Advanced ..........................................................................................55

Chipset ..............................................................................................71

Security .............................................................................................73

Boot ..................................................................................................74

Save & Exit ........................................................................................75

Appendix A: Watchdog .........................................76

iv

TPPC 2210 and TPPD 2200 Series User Manual

Preface

PrefaCe

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

TPPC 2210, TPPC 2210T and TPPD 2200 are trademarks of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense.

CE

The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.

v

TPPC 2210 and TPPD 2200 Series User Manual

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status Update

NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green

products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2011/65/EU, to be your trusted green partner and to protect our environment.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force to implement the introduction of green products. The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2013 will be RoHS compliant. They will use the usual NEXCOM naming convention.

vi

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM. HCP series products (Blade Server) which are manufactured by NEXCOM are covered by a three year warranty period.

NEXCOM Return Merchandise Authorization (RMA)

▪ Customers shall enclose the “NEXCOM RMA Service Form” with the

returned packages.

▪ Customers must collect all the information about the problems

encountered and note anything abnormal or, print out any on-screen messages, and describe the problems on the “NEXCOM RMA Service Form” for the RMA number apply process.

▪ Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, NEXCOM is not responsible for the devices/parts.

▪ Customers are responsible for the safe packaging of defective products,

making sure it is durable enough to be resistant against further damage and deterioration during transportation. In case of damages occurred during transportation, the repair is treated as “Out of Warranty.”

▪ Any products returned by NEXCOM to other locations besides the

customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

System Level

▪ Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistor, capacitor.

▪ Items will be replaced with NEXCOM products if the original one cannot

be repaired. Ex: motherboard, power supply, etc.

▪ Replace with 3rd party products if needed.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Board Level

▪ Component fee: NEXCOM will only charge for main components, such

as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistors, capacitors.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

vii

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

viii

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

▪ A Philips screwdriver

▪ A flat-tipped screwdriver

▪ A grounding strap

▪ An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

Safety Information

Before installing and using the device, note the following precautions:

▪ Read all instructions carefully.

▪ Do not place the unit on an unstable surface, cart, or stand.

▪ Follow all warnings and cautions in this manual.

▪ When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪ Avoid using the system near water, in direct sunlight, or near a heating

device.

▪ The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability.

▪ The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

ix

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a

damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or

letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting

the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not

place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work

according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

x

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling: – Product name and serial number – Detailed information of the peripheral devices – Detailed information of the installed software (operating system,

version, application software, etc.) – A complete description of the problem – The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.

Conventions Used in this Manual

Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.

CAUTION!

CAUTION!CAUTION!

Caution: Information to avoid damaging components or losing data.

Note: Provides additional information to complete a task easily.

xi

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

9F, No. 920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7786 Fax: +886-2-8226-7782 www.nexcom.com

America

USA NEXCOM USA

2883 Bayview Drive, Fremont CA 94538, USA Tel: +1-510-656-2248 Fax: +1-510-656-2158 Email: [email protected] www.nexcom.com

Asia

Taiwan NEXCOM Intelligent Systems

Taipei Office

13F, No.920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7796 Fax: +886-2-8226-7792 Email: [email protected] www.nexcom.com.tw

NEXCOM Intelligent Systems Taichung Office

16F, No.250, Sec. 2, Chongde Rd., Beitun Dist., Taichung City 406, R.O.C. Tel: +886-4-2249-1179 Fax: +886-4-2249-1172 Email: [email protected] www.nexcom.com.tw

Japan NEXCOM Japan

9F, Tamachi Hara Bldg., 4-11-5, Shiba Minato-ku, Tokyo, 108-0014, Japan Tel: +81-3-5419-7830 Fax: +81-3-5419-7832 Email: [email protected] www.nexcom-jp.com

China

NEXCOM China

Floor 5, No.4, No.7 fengxian middle Rd., (Beike Industrial Park), Haidian District, Beijing, 100094, China Tel: +86-10-5704-2680 Fax: +86-10-5704-2681 Email: [email protected] www.nexcom.cn

xii

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Europe

United Kingdom NEXCOM EUROPE

10 Vincent Avenue, Crownhill Business Centre, Milton Keynes, Buckinghamshire MK8 0AB, United Kingdom Tel: +44-1908-267121 Fax: +44-1908-262042 Email: [email protected] www.nexcom.eu

Italy NEXCOM ITALIA S.r.l

Via Lanino 42, 21047 Saronno (VA), Italia Tel: +39 02 9628 0333 Fax: +39 02 9625 570 Email: [email protected] www.nexcomitalia.it

NEXCOM Shanghai

Room 603/604, Huiyinmingzun Plaza Bldg., 1, No.609, Yunlin East Rd., Shanghai, 200333, China Tel: +86-21-5278-5868 Fax: +86-21-3251-6358 Email: [email protected] www.nexcom.cn

NEXCOM Surveillance Technology Corp.

Room202, Building B, the GuangMing Industrial Zone Zhonghua Rd., Minzhi Street, Longhua District, Shenzhen 518131, China Tel: +86-755-8364-7768 Fax: +86-755-8364-7738 Email: [email protected] www.nexcom.cn

NEXCOM United System Service

Hui Yin Ming Zun Building Room 1108, Building No. 11, 599 Yunling Road, Putuo District, Shanghai, 200062, China Tel: +86-21-6125-8282 Fax: +86-21-6125-8281 Email: [email protected] www.nexcom.cn

xiii

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Package Contents

Before continuing, verify that the TPPC 2210(T)/TPPD 2200 package that you received is complete. Your package should have all the items listed in the following table.

TPPC 2210/TPPC 2210T

Item Name Qty

1 I/O Cable 1 2 Power Cable 1 3 SATA Cable 1 4 Driver DVD 1

TPPD 2200

Item Name Qty

1 Power Cable 1

I/O Cable Power Cable

xiv

TPPC 2210 and TPPD 2200 Series User Manual

Preface

Ordering Information

The following below provides ordering information for the AIO PPC and display.

• Barebone

TPPC 2210 (P/N: 10ID0221001X0)

In-Vehicle Signage Panel PC powered by Intel

®

Celeron® Processor N2807

1.58GHz

TPPC 2210T (P/N: 10ID0221000X0)

In-Vehicle Signage Panel PC with CAT5 TX Extender powered by Intel

®

Celeron

®

Processor N2807 1.58GHz

TPPD 2200 (P/N: 10ID0220000X0)

21.5” Full-HD Vehicle Display with CAT5 Interfaces

• Options

1. VESA Mount Kit (P/N:)

▪ 1x VESA Mount Bracket ▪ 8x Screws ▪ 8x P3 Screws ▪ 6x M5 Screws

1

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

ChaPter 1: ProduCt IntroduCtIon

Key Features

▪ 16:9 21.5” Fanless Panel Computer

▪ Intel

®

Celeron® processor N2807

▪ Wide-range power input of 12V to 36V DC

▪ Front bezel compliant with IP54

▪ Tempered glass

▪ Support Wi-Fi, 3G and GPS modules

▪ DDR3L up to 4GB, 2.5” SSD bracket, two speakers

TPPC 2210

Overview

2

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Key Features

▪ 16:9 21.5” Fanless Panel Computer

▪ Intel

®

Celeron® processor N2807

▪ Wide-range power input of 12V to 36V DC

▪ Front bezel compliant with IP54

▪ Tempered glass

▪ Support Wi-Fi, 3G and GPS modules

▪ DDR3L up to 4GB, 2.5” SSD bracket, two speakers

▪ Support Cat 5 Extender Daisy Chain (TX)

TPPC 2210T

Overview

3

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Key Features

▪ 16:9 21.5” Full-HD TFT LCD panel

▪ Wide-range power input of 12V to 36V DC

▪ Front bezel compliant with IP54

▪ Tempered glass

▪ Support Cat 5 Extender Daisy Chain (TX/RX)

TPPD 2200

Overview

4

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Hardware Specifications

Panel

(TPPC 2210/TPPC 2210T/TPPD 2200)

▪ LCD size: 21.5”, 16:9 ▪ Resolution: Full HD, 1920 x 1080 ▪ Luminance: 500 cd/m² ▪ Contrast ratio: 3,000 ▪ LCD color: 16.7M ▪ Viewing angle: 178 (H), 178 (V) ▪ Backlight: LED

System

(TPPC 2210/TPPC 2210T)

▪ CPU: Intel

®

Bay Trail N2807 Dual Core 1.58GHz ▪ BIOS: AMI BIOS ▪ System chipset: Intel® integrated ▪ System memory:

1x 204-pin DDR3L SODIMM socket, up to 4GB, support up to

1333/1066MHz with un-buffered and Non-ECC ▪ Hard drive bay: optional 2.5” SATA SSD ▪ Watchdog timer: Watchdog timeout can be programmed by software

from 1 second to 255 seconds and from 1 minute to 255 minutes

(Tolerance 15% under room temperature 25°C) ▪ H/W status monitor: Monitors system temperature, and voltage ▪ Expansion: 2x Mini-PCIe sockets ▪ Cat 5 Extender TX board (TPPC 2210T only)

(TPPD 2200)

▪ CPU: Novatek Panel controller NT68660 ▪ Cat.5 Extender TX/RX board

Rear I/O

(TPPC 2210/TPPC 2210T)

▪ COM : 1x RS232 ▪ Ethernet: 1x RJ45 ▪ USB: 2x USB 2.0 ▪ Power switch ▪ DC-IN ▪ Cat.5 Extender

(TPPC 2210/TPPC 2210T)

▪ DC-IN ▪ Cat 5 Extender TX ▪ Cat 5 Receiver RX (TPPD 2200 only)

Audio

(TPPC 2210/TPPC 2210T)

▪ ALC622 audio codec ▪ Two 2W speakers

Ethernet

(TPPC 2210/TPPC 2210T)

▪ LAN chip: Realtek RTL8111G Gigabit LAN ▪ Ethernet interface: 10/100/1000 Based-Tx

Mechanical and Environment

▪ Color: pantone black ▪ Mounting: (Optional)

VESA Mount Kit (75x75; 100x100; 200x200)

5

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Vehicle Mount Kit

▪ Power input: 12V ~ 36V DC ▪ Vibration: (w/SSD)

Random vibration test (Operating): 1g @5~500Hz Operating: MIL-STD-810G, 514.6 Procedure 1, Category 4 Storage: MIL-STD-810G, 514.6 Procedure 1, Category 24

▪ Shock:

Operating: MIL-STD-810G, Method 516.6, Procedure I, Trucks and semi-

trailers= 20g

Crash hazard: MIL-STD-810G, Method 516.6, Procedure V, Ground

equipment= 75g ▪ Operating temperature: -10°C to 40°C ▪ Storage temperature: -20°C to 60°C ▪ Operating humidity: 10 to 90% (Non-condensing) ▪ Dimension: 528.46mm x 323.06mm x 58mm (W x D x H) ▪ Weight: 7kg

Certification

▪ CE approval ▪ FCC Class A ▪ E-Mark: E-13

6

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Knowing Your TPPC 2210/TPPC 2210T

Rear Bottom

Antenna Holes for Optional Wi-Fi

The 3 external antenna mounting holes are used to mount and connect optional Wi-Fi/GPS/GSM antennas.

Power Switch

Press to power-on or power-off the system.

LAN / COM

Used to connect the system to a local area network. The COM port supports RS232 compatible serial devices.

USB

Used to connect USB 2.0/1.1 devices.

Cat.5 Extender TX (TPPC 2210T Only)

Extender Video signal over Cat 5 Cable.

12-36V DC Input

Used to plug a DC power cord.

Knowing Your TPPD 2200

Rear Bottom

Cat.5 Extender TX

Extender video signal over Cat 5 cable.

Cat.5 Receiver RX

Receive video signal from TX side over Cat 5 cable.

12-36V DC Input

Used to plug a DC power cord.

7

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Rear and VESA Mount

VESA Mounting Hole for TPPC 2210/TPPD 2200

The VESA mount fixed on the machine.

VESA Mounting Hole for Bracket

VESA Mounting Hole 75 x 75mm VESA Mounting Hole 100 x 100mm VESA Mounting Hole 200 x 200mm

8

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

Mechanical Dimensions

TPPC 2210

528.46

58.00

SCALE 0.500

25.00

46.53219.80

101.73

426.73

323.06

9

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

TPPD 2200

530.46

97.73 335.00

323.00

57.80

SCALE 0.500

10

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 1: Product Introduction

With VESA Mount

530.46

25.00

58.00

100.00

75.00

100.00

200.00

SCALE 0.500

68.40

97.73

432.73

323.06

219.80 46.53

11

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

ChaPter 2: JumPers and ConneCtors

This chapter describes how to set the jumpers and connectors for the TPPC 2210 and TPPD 2200 series.

Before You Begin

▪ Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep

small components separated.

▪ Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow

require only a few simple tools, including the following:

– A Philips screwdriver

– A flat-tipped screwdriver

– A set of jewelers screwdrivers

– A grounding strap

– An anti-static pad

▪ Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect

connections as these can damage the soft metal or plastic parts of the

connectors.

▪ Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching

a metal object. Static electricity can damage many of the electronic

components. Humid environments tend to have less static electricity than

dry environments. A grounding strap is warranted whenever danger of static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪ Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪ If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.

▪ Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.

▪ Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation.

▪ Use correct screws and do not over tighten screws.

12

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

1

2

3

1

2

3

13

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

TPPC 2210 consists of a motherboard, power board and TX board. TPPD 2200 consists of an AD board and RX board.

This chapter lists the pinout assignment of the jumpers and connectors on the motherboard and AD board, and the location of the jumpers and connectors on the power, TX and RX board.

INVERTER

Front Panel

Audio Header

(FP_AUDIO)

SATA Power

(PWOUT)

COM Headers

COM1 COM2 COM3 COM4

SATA II Port

(SATA1)

CPUFAN

Header

LANLED

Headers (LAN1LED LAN2LED)

SMBUS Header

PS2 KB/MS

Header

Front Panel

Header (FP)

Power

Switch

Reset

Button

USB 2.0 Header (USB2/4)

GPIO Header

Full-size

Mini-PCIe/mSATA Slot

LVDS Header

SPDIF Out Header

Half-size Mini-PCIe

DDR3L

SO-DIMM Slot

Line-out

USB 3.0

over USB 2.0

DVI-I Port

RJ-45 LANRJ-45 LANDual

USB 2.0

9V ~ 24V DC Input

Top View

TPPC 2210 and TPPD 2200 System Boards

Location of the Connectors for TPPC 2210 Motherboard

14

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Bottom View

15

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

JP2

COPEN

AT-MODE

JBAT

JP7

JP3

JP5

JP1

JP4

JP6

Top View

Location of the Jumpers for TPPC 2210 Motherboard

16

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Name Description

JP1 LVDS PVCC 5V/3.3V/12V Select 4-Pin Block JP2 INVERTER VCC 5V/12V Select 3-Pin Block JP3 COM4 Header Pin9 Function Select 4-Pin Block JP4 COM3 Header Pin9 Function Select 4-Pin Block JP5 COM2 Header Pin9 Function Select 4-Pin Block JP6 COM1 Header Pin9 Function Select 4-Pin Block

JBAT CMOS RAM Clear Function Setting 2-Pin Block

COPEN Case Open Message Display Function 2-Pin Block

AT_MODE AT Mode Function Select 2-Pin Block

JP7 Security Measure Function Select 2-Pin Block

Connector Table

Connector Name

DCIN DC 9V-24V Power-in Connector

SATA 1 SATAII Port Connector

PWOUT1 SATA Power out Connector

CPUFAN CPUFAN Connector

INVERTER LVDS Inverter Connector

USB1/USB3(Top) USB 2.0 Port Connector X3

USB3(Bottom) USB 3.0 Port Connectors X1

LAN1/2 RJ-45 LAN Port Connector X2

DVI DVI-I Port Connector

AUDIO Audio Line Out Connector

Connector Name Description

FP_AUDIO Front Panel Audio Header 9-pin Block

SPDIFOUT SPDIF Out Header 2-pin Block

COM1/2/3/4 Serial Port Header X4 9-pin Block

GPIO GPIO Header 10-pin Block

USB3/USB4 USB 2.0 Header 9-pin Block

SMBUS SMBUS Header 4-pin Block

PS2KBMS PS2KBMS Header 6-pin Block

FP

Front Panel Header (PWR LED/HDD LED/

Power Button/Reset)

8-pin Block

LAN1LED LAN2LED

LAN Activity LED Headers 2-pin Block

LVDS 24-bit LVDS Header 30-pin Block

Motherboard

Jumper Table Header Table

17

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Jumpers

LVDS PVCC 3.3V/5V/12V Function Select

Connector type: 4-pin header Connector location: JP1

Inverter VCC 5V/12V Select

Connector type: 1x3 3-pin header Connector location: JP2

Pin Status Settings

2-4 Short VCC= 3.3V 3-4 Short VCC= 5V 4-6 Short VCC= 12V

Pin Status Settings

1-2 Short VCC= 5V 2-3 Short VCC= 12V

15

26

13

15

26

15

26

18

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

COM4 Header Pin 9 Function Select

Connector type: 4-pin header Connector location: JP3

COM3 Header Pin 9 Function Select

Connector type: 4-pin header Connector location: JP4

Pin Status Settings

2-4 Short RI= RS232 3-4 Short RI= 5V 4-6 Short RI= 12V

Pin Status Settings

2-4 Short RI= RS232 3-4 Short RI= 5V 4-6 Short RI= 12V

15

26

15

26

15

26

15

26

15

26

15

26

19

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

COM2 Header Pin 9 Function Select

Connector type: 4-pin header Connector location: JP5

COM1 Header Pin 9 Function Select

Connector type: 4-pin header Connector location: JP6

Pin Status Settings

2-4 Short RI= RS232 3-4 Short RI= 5V 4-6 Short RI= 12V

Pin Status Settings

2-4 Short RI= RS232 3-4 Short RI= 5V 4-6 Short RI= 12V

15

26

15

26

15

26

15

26

15

26

15

26

20

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

12

Clear CMOS

Connector type: 1x2 2-pin header Connector location: JBAT

Case Open Message Display Function Select

Connector type: 1x2 2-pin header Connector location: COPEN

Pin Status Settings

1-2 Open Normal 1-2 Short Clear CMOS

Pin Definition

1 Case open function 2 GND

Pin 1-2 Closed (Short): To enable case open detection, short the case open function pin to GND and enable the ‘Case Open Detect’ function in the BIOS menu. When enabled, if the case is removed and the computer reboots, a message will be displayed on screen to inform you about the removal.

21

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

12

AT Mode Function Select

Connector type: 1x2 2-pin header Connector location: AT-MODE

Security Measure Function Select

Connector type: 1x2 2-pin header Connector location: JP7

Pin Status Settings

1-2 Open Normal 1-2 Short AT Mode Selected

Pin 1-2 Closed (Short): Enables AT_MODE function. When enabled, the computer will automatically turn back on after power resumes from a sudden failure.

Pin Status Settings

1-2 Open

Enable Security Measures in the

Flash Descriptor (Default)

1-2 Short

Disable Security Measures in the

Flash Descriptor (Override)

22

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

Rear I/O Connectors

1 7

Pin Definition Pin Definition

1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 8

SATA Power Connector

Connector type: 1x4 4-pin header Connector location: PWOUT

Pin Definition Pin Definition

1 +5V 2 GND 3 GND 4 +12V

14

SATA II Connector

Connector type: Standard Serial ATA 7P (1.27mm, SATA-M-180) Connector location: SATA1

Line-out Port

9V~24V DC

Power-in

Connector

USB 3.0

USB 2.0

USB 2.0 Ports

DVI-I Port

RJ-45 LAN Ports

23

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

CPU Fan Connector

Connector type: 1x4 4-pin header Connector location: CPUFAN

LVDS Inverter Connector

Connector type: 1x8 8-pin header Connector location: INVERTER

Pin Definition Pin Definition

1 GND 2 VCC 3 Fan Clock 4 Control

Pin Definition Pin Definition

1 Backlight Enable 2 Backlight PWM 3 PVCC 4 PVCC 5 GND 6 GND 7 Backlight Up SW 8 Backlight Down SW

14

81

24

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

19

21

0

Line-out and Mic-in Header

This header connects to the front panel line-out and mic-in through cable. Connector type: 2x5 10-pin header Connector location: FP_AUDIO

Pin Definition Pin Definition

1 MIC-R 2 GND 3 MIC-L 4 NC 5 Lineout-R 6 NC 7 NC 8 KEY 9 Lineout-L 10 NC

Pin Definition

1 SPDIFOUT 2 GND

12

SPDIF Out Header

Connector type: 1x2 2-pin header Connector location: SPDIFOUT

25

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

15

6

Serial Port Headers

Connector type: 2x5 9-pin header Connector location: COM4, COM3, COM2 and COM1

Pin Definition Pin Definition

1 DCD 2 SIN 3 SOUT 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI

19

21

0

GPIO Header

Connector type: 2x5 10-pin header Connector location: GPIO

Pin Definition Pin Definition

1 GPIO_80 2 GPIO_81 3 GPIO_82 4 GPIO_83 5 GPIO_84 6 GPIO_85 7 GPIO_86 8 GPIO_87 9 GND 10 VCC

26

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

1

21

0

14

USB 2.0 Port Header

Connector type: 2x5 9-pin header Connector location: USB2 and USB4

SMBus Header

Connector type: 1x4 4-pin header Connector location: SMBUS

Pin Definition Pin Definition

1 VCC 2 VCC 3 -DATA 4 - DATA 5 +D ATA 6 + DATA 7 GND 8 GND

10 NC

Pin Definition Pin Definition

1 VCC 2 SMBUS_CLK 3 GND 4 SMBUS_DATA

27

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

17

PS/2 Keyboard & Mouse Header

Connector type: 1x7 6-pin header Connector location: PS2KBMS

Pin Definition Pin Definition

1 VCC 3 KB_DATA 4 KB_CLK 5 GND 6 MS_CLK 7 MS_DATA

17

28

Front Panel Header

Connector type: 2x4 8-pin header Connector location: FP

Pin Definition Pin Definition

1 HDDLED+ 2 PWRLED+ 3 HDDLED- 4 PWRLED5 RSTSW 6 PWRBTN 7 GND 8 GND

28

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Pin Definition

1 LED+ 2 LED-

12

LAN Activity LED Headers

Connector type: 1x2 2-pin header Connector location: LAN1LED and LAN2LED

24-bit Dual Channel LVDS Header

Connector type: 2x15 30-pin header Connector location: LVDS

1

2

29

30

Pin Definition Pin Definition

1 LVDSB_DATAN3 2 LVDSB_DATAP3 3 LVDS_CLKBN 4 LVDS_CLKBP 5 LVDSB_DATAN2 6 LVDSB_DATAP2 7 LVDSB_DATAN1 8 LVDSB_DATAP1

9 LVDSB_DATAN0 10 LVDSB_DATAP0 11 NC/DDC_DATA 12 NC/DDC_CLK 13 GND 14 GND 15 GND 16 GND 17 LVDSA_DATAP3 18 LVDSA_DATAN3 19 LVDS_CLKAP 20 LVDS_CLKAN 21 LVDSA_DATAP2 22 LVDSA_DATAN2 23 LVDSA_DATAP1 24 LVDSA_DATAN1 25 LVDSA_DATAP0 26 LVDSA_DATAN0 27 PVCC 28 PVCC 29 PVCC 30 PVCC

29

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

KQ2

KQ3

I2

I3

KQ4

K4

KQ6

TX4

TX3

DO3

DO6

M5

G8

I4

2

5

9

3

2

4

7

4

2

5

23

35

2

5

2

4:

51

5

2

24

2

3

2 3 2 4

2

3

2

3

7

6

2

3

CN1

CN3

CN6

CN7

CN4

CN2

J5

J4

JP4

SW1

J1

J2

GC26

N2:

S231

S229

S228

S227

GC25

S22:

S226

D216

D217

D215

S59

D214

E23

D213

S225

D212

DU7

S224

DU6

D211

DU5

D::

D:9

S223

S222

N29

S221

S21:

N27

N28

S218

S217

E22

S216

S219

D:8

S215

S214

N26

E21

E:

S212

S213

S211

D:7

N25

D:6

D:5

D:4

E8

E9

2

6

2

3

2

4

7

4

2

5

2

3

2

4

2

3

2

3

2

7

6

23

35

2

5

2

5

2

24

2

6

5

9

2

,

,3,

,,

,

Top View

Bottom View

Location of the Jumpers and Connectors for TPPC 2210 Power Board

30

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Definition

CN1 COM/Audio/USB/signal connect to MB CN2 COM/LAN Connector CN3 DC 5V Output CN4 USB 2.0 x 2 port CN6 DC 12V Output CN7 DC 9 -36V Input Connector

J1 R Speaker Connector J2 L Speaker Connector J4 LAN signal connect to MB J5 LAN signal connect to MB

JP4 Audio Pin Header

SW1 Power Push Button

Power Board

Jumper and Connector Table

31

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

KQ2

I3

KQ3

I2

DO4

I5

DO3

V22

I4

3

2:

2

6 2

7

6

3

2

B C D

3456789

:

21

222324

25

E F G H I K L M N O Q

9

8

23 22

3

2

21 :

CN2

CN3

U11

Top View

Location of the Jumpers and Connectors for TPPC 2210 TX Board

32

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Definition

CN2 DC 5V Input CN3 CAT 5 TX Port for Video Extended U11 HDMI Input Port

TX Board

Connector Table

33

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

I3

I2

D5

KQ4

KQ3

KQ2

KQ6

DO2

MBO3

V21

V:

MBO2

V26

I5

KQ5

I4

29 2: 31

2:

2

7

6

3

2

43

28

75

5:

59

UZXWVMNOQ

S

G

HIK

L

BCD

E

F

2 3

44

27

2

8

9

23 22

4 5 6 7 8

5:

59

75

2

27

44

9 : 21 22

28

43

2

3

21 :

24 25 26 27 28

6

2

M

N

O

Q

7

GHI

K

L

BCDEF

6

3

6

2

6

2

23

2 3 4 5 6

3

8

9

22

7 8 9 :

21

2

3

21

22 23 24 25

2

:

LAN 2

LAN 1

CN1

U15

Top View

Location of the Jumpers and Connectors for TPPD 2200 RX Board

34

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

S274

S272

S271

D324

GC29

D323

S273

D322

S269

S26:

D321

D31:

D319

V3

D331

D342

D317

D315

D313

D2:7

D316

D312

D314

D318

D28

D333

D332

S283

S281

D338

D337

D632

D631

D2:4

D311

D2:9

D2:8

D2:1

D2:3 D2:6

D2::

D2:5

D2:2

D334

D335

S282 D336

D62:

D618

D292

D29:

D299

D298

D294

D297

S267

S268

D295

D296

D293

V8

S2:

S284

D339

D341

D278

D274

D276

D277

D275

D273

D272

D271

D26:

D261

D27:

D283

D282

D281

D279

GC27

D28:

D291

D289

D288

GC28

S252

D33:

D629

D257

D258

D267

D264

D287

D59

D269

D285

D266

D284

D268

D265

D286

S259

D86

D84

S277 D329

D628

D627

D246

D239

D256

D255

D254

D253

D252

D251 D23: D242

D24:

D249

D259

D248

D262

M3

D263

D25:

D247

D236

GC26

D325

S279

S278 D32:

D328

D233

D228

D222

D617

D217 D21:

D226

D219 D221

D231

D22:

D223

D69

GC25

D237

D235

D234

D229

D244

D326

S27: D327

D218

D:9

D213

D211

D::

D216

D:3

D:8

D:7

D:6

D:5

D215

D:4

D212

D214

GC24

GC23

D53

D:2

D245

D238

D243

D241

D:1

D9:

D99

D98

D224

D227

D225

D232

3

2

6

2

6

2

6

2

7

3

23

8

9

22

3

21

2

:

8

9

22 23

2

3

:

21

76

32

Bottom View

35

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Definition

CN1 DC 5V Input LAN1 CAT 5 RX Port for Receive TX Signal LAN2 CAT 5 TX Port for Video Extended

U15 HDMI Input Port

RX Board

Connector Table

36

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

CN3 CN2

CN13

CN17

CN9

CN5

CN4

CN7

CN16

CN10 CN11

CN14

Top View

Location of the Jumpers and Connectors for TPPD 2200 AD Board

37

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Jumpers

Backlight Adjust

Connector type: 1x2 2-pin header, 2.54mm pitch Connector location: CN17

Panel VCC Select

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: CN5

Pin Status Settings

1-2 Short DC Adjust 1-2 Open PWM Adjust

Pin Status Settings

1-2 Short Panel VCC 5V IN 2-3 Short Panel VCC 3.3V IN

13

12

38

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Panel Number Select

Connector type: 1x2 2-pin header, 2.54mm pitch Connector location: CN10, CN11 and CN14

No.

Panel Jumper, X: Location to set the

jumper on (short)

CN10

(Panel1)

CN11

(Panel2)

CN14

(Panel3)

1 2 X Short pin 1-2 on CN14 3 X Short pin 1-2 on CN11 4 X X Short pin 1-2 on CN11 and CN14 5 X Short pin 1-2 on CN10 6 X X Short pin 1-2 on CN10 and CN14 7 X X Short pin 1-2 on CN10 and CN11 8 X X X Short pin 1-2 on CN10, CN11 and CN14

21

CN10

CN11

CN14

39

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

DC Power Input (12V ~ 24V)

Connector type: 1x4 4-pin header, 2.0mm pitch Connector location: CN16

Pin Definition Pin Definition

1 12V 2 12V 3 GND 4 GND

Pin Definition

1 GND 2 5V

1

4

12

DC Power Output (5V)

Connector type: 1x2 2-pin header, 2.0mm pitch Connector location: CN2

40

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Backlight Power and Signal Output

Connector type: 1x6 6-pin header, 2.0mm pitch Connector location: CN3

LVDS Connector

Connector type: 2x15 30-pin header, 2.0mm pitch Connector location: CN9

Pin Definition Pin Definition

1 12V 2 12V 3 GND 4 GND 5 BL ON/OFF 6 BL ADJ

Pin Definition Pin Definition

1 RXO0- 2 RXO0+ 3 RXO1- 4 RXO1+ 5 RXO2- 6 RXO2+ 7 GND 8 GND

9 RXOC- 10 RXOC+ 11 RXO3- 12 RXO3+ 13 RXE0- 14 RXE0+ 15 RXE1- 16 RXE1+ 17 RXE2- 18 RXE2+ 19 GND 20 GND 21 RXEC- 22 RXEC+ 23 RXE3- 24 RXE3+ 25 GND 26 GND 27 GND 28 VSEL 29 VSEL 30 VSEL

1

2 30

6

29

41

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

Keypad Input

Connector type: 1x8 8-pin header, 2.0mm pitch Connector location: CN13

VGA Connector

Connector type: VGA Connector location: CN7

Pin Definition Pin Definition

1 GND 2 LED R (Red) 3 LED G (GREEN) 4 Key 1 (On/Off) 5 Key 2 (Down) 6 Key 3 (Menu) 7 Key 4 (Up) 8 Key 5 (Auto/Exit)

Pin Definition Pin Definition

1 VGA_Rin 2 VGA_Gin

3 VGA_Bin 4 NC

5 VGA_DET 6 GND

7 GND 8 GND

9 VGA_5V 10 GND 11 NC 12 VGA_SDA 13 HS_VGA 14 VS_VGA 15 VGA_SCL

1

11

8

5

15

42

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 2: Jumpers and Connectors

DVI Connector

Connector type: DVI Connector location: CN4

Pin Definition Pin Definition

1 RX2- 2 RX2+ 3 GND 4 RX45 RX4+ 6 SCL 7 SDA 8 VS

9 RX1- 10 RX1+ 11 GND 12 RX313 RX3+ 14 5V 15 GND 16 HP 17 RX0- 18 RX0+ 19 GND 20 RX521 RX5+ 22 GND 23 RXC+ 24 RXC-

8

24

1

11

43

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

ChaPter 3: system setuP

Removing the Chassis Cover

Prior to removing the chassis cover, make sure the unit’s power is off and disconnected from the power sources to prevent electric shock or system damage.

CAUTION!

CAUTION!CAUTION!

1. Remove the mounting screws around the chassis cover and then remove the cover.

2. Align the mounting holes that are on the sides of the SATA drive with the mounting holes on the drive bay and then use the provided mounting screws to secure the drive in place.

44

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

3. Place the SATA drive in the chassis and then use the provided mounting screws to secure the drive in the chassis.

Connect the SATA data cable and SATA power cable to the connectors on

the SATA drive.

SATA data & power connector

45

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

Installing a SO-DIMM Memory Module

2. Push the module down until the clips on both sides of the socket lock into position. You will hear a distinctive “click” sound, indicating the module is correctly locked into position.

1. Insert the module into the socket at an approximately 30 degrees angle. Apply firm even pressure to each end of the module until it slips into the socket. The gold-plated connector on the edge of the module will almost completely disappear inside the socket.

Memory module

46

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

1. The Mini PCIe module package includes the following items.

Mini PCIe Module

Antennas

RF Cables

Installing a Mini PCIe Module (Optional)

2. Insert the Mini PCIe module into the Mini PCIe slot at a 45 degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot

47

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

3. Secure the module with mounting screws. 4. Attach one end of the RF cables onto the module.

Mounting screw RF cable

48

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

5. Insert the antenna jack end of the cable through the antenna hole.

Antenna jack end of the cable

6. Insert the ring onto the antenna jack end of the cable.

Ring

Antenna jack

49

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

Installing VESA Mount (Optional)

1. For VESA mounting, align the mounting holes on the VESA mount bracket to the mounting holes on the back cover.

Mounting hole

50

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 3: System Setup

2. Secure the VESA mount bracket to the back cover with screws.

51

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

ChaPter 4: BIos setuP

This chapter describes how to use the BIOS setup program for the TPPC 2210 and TPPD 2200 series. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future.

To check for the latest updates and revisions, visit the NEXCOM Web site at www.nexcom.com.tw.

About BIOS Setup

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters.

These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.

With easy-to-use pull down menus, you can configure such items as:

▪ Hard drives, diskette drives, and peripherals

▪ Video display type and display options

▪ Password protection from unauthorized use

▪ Power management features

The settings made in the setup program affect how the computer performs. It is important, therefore, first to try to understand all the setup options, and second, to make settings appropriate for the way you use the computer.

When to Configure the BIOS

▪ This program should be executed under the following conditions:

▪ When changing the system configuration

▪ When a configuration error is detected by the system and you are

prompted to make changes to the setup program

▪ When resetting the system clock

▪ When redefining the communication ports to prevent any conflicts

▪ When making changes to the Power Management configuration

▪ When changing the password or making other changes to the security

setup

Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS RAM has lost power, or the system features need to be changed.

52

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering Setup

When the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines. These routines perform various diagnostic checks; if an error is encountered, the error will be reported in one of two different ways:

▪ If the error occurs before the display device is initialized, a series of beeps

will be transmitted.

▪ If the error occurs after the display device is initialized, the screen will

display the error message.

Powering on the computer and immediately pressing <Del> allows you to enter Setup.

Press the

key to enter Setup:

Legends

Key Function

Moves the highlight left or right to select a menu.

Moves the highlight up or down between sub-menus or fields.

Exits the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted field.

Scrolls backward through the values or options of the highlighted field.

Selects a field.

Displays General Help.

Load previous values.

Load optimized default values.

Saves and exits the Setup program.

Press <Enter> to enter the highlighted sub¬menu

53

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press .

54

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

BIOS Setup Utility

Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from several setup functions and one exit. Use arrow keys to select among the items and press to accept or enter the submenu.

Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Monday to Sunday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1999 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set the Date. Use Tab to switch between Date elements.

BIOS Information BIOS Vendor Core Version Filename Build Date and Time

System Date

System Time

Access Level

TXE Information TXE FW Version

American Megatrends

5.009 BF3ASSE3 08/04/2015 18:25:36

[Fri 10/16/2015] [16:20:36]

Administrator

01.01.00.1089

Save & ExitAdvanced Chipset Security BootMain

55

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Energy-Related Products function.

Disable ERP to active all wake-up functions.

ERP Support [Disabled]

OS Selection [Windows 7] ACPI Settings Wake-up Function Settings

Super IO Conguration SmartFAN Conguration

PC Health Status

Shutdown Temperature Conguration

Serial Port Console Redirection

CPU Conguration PPM Conguration SATA Conguration Network Stack Conguration CSM Conguration USB Conguration

Realtek PCIe GBE Family Controller (MAC:00:30:18:C3:F8:79) Realtek PCIe GBE Family Controller (MAC:00:30:18:C3:F8:7A)

Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Setting incorrect field values may cause the system to malfunction.

Save & ExitAdvanced Chipset Security BootMain

ERP Function

Set this option to Disabled to activate all wake-up functions. The available options are Auto and Disabled.

OS Selection

Selects the operating system as Windows 7 or Windows 8.X.

56

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

ACPI Settings

This section is used to configure ACPI Settings.

Exit

Advanced Chipset PCIPnP Security

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

ACPI Settings

ACPI Sleep State [S3 (Suspend to RAM)]

ACPI Sleep State

Select the highest ACPI sleep state the system will enter when the suspend button is pressed. The options are Suspend Disabled and S3(Suspend to RAM).

Wake-up Function Settings

This section is used to enable or disable system wake-up functions.

Wake system with Fixed Time

This section is used to enable or disable system wake on alarm event. When enabled, system will wake on the HR:MIN:SEC specified.

PS2 KB/MS Wake-up

This section is used to enable or disable system wake on PS2 keyboard or mouse from S3/S4/S5 state.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or disable System wake on alarm event. When enabled, System will wake on the

hr:min:sec specied

Wake system with Fixed Time

PS2 KB/MS Wake-up

[Disabled]

57

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Super IO Configuration

This section is used to configure serial ports 1 to 4 of the super IO.

Super IO Chip

Displays the Super I/O chip used on the board.

OS Select for Serial Port

Configures which operating system to enable serial port support.

Case Open Detect

Enables or disables case open detection feature.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set Parameters of Serial Port 1 (COMA)

Super IO Conguration

Serial Port 1 Conguration

Serial Port 2 Conguration Serial Port 3 Conguration Serial Port 4 Conguration

OS Select For Serial Port

WatchDog Timer

WatchDog Wake-up Timer in ERP

ATX Power Emulate AT Power

Case Open Detect

[Windows]

[Disabled]

-Enabled-

[Disabled]



WatchDog Timer

Enables or disables watchdog timer control. When enabled, the following sub-menus are available:

WatchDog Timer Value

Configures the watchdog timer value.

WatchDog Timer Unit

Configures the metrics used for the watchdog timer.

WatchDog Wake-up Timer in ERP

Enables or disables watchdog wake-up timer when ERP function is disabled.

58

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Serial Port 1 Configuration Serial Port 2 Configuration

Change Settings

Selects an optimal setting for the Super IO device.

Transmission Mode Select

Configures the serial port mode to RS232, RS422 or RS485.

Mode Speed Select

Configures the speed of the serial port modes.

Serial Port FIFO Mode

The options are 16-Byte FIF0, 32-Byte FIF0, 64-Byte FIF0 and 128-Byte FIF0.

Change Settings

Selects an optimal setting for the Super IO device.

Serial Port FIFO Mode

The options are 16-Byte FIF0, 32-Byte FIF0, 64-Byte FIF0 and 128-Byte FIF0.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 1 Conguration

Serial Port

Device Settings

Change Settings Transmission Mode Select Mode Speed Select Serial Port FIFO Mode

[Enabled]

IO=3F8h; IRQ=4;

[Auto] [RS232] [RS232=1Mbps,RS422/R...] [128-Byte FIFO]

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 2 Conguration

Serial Port

Device Settings

Change Settings Serial Port FIFO Mode

[Enabled]

IO=2F8h; IRQ=3;

[Auto] [128-Byte FIFO]

59

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Serial Port 3 Configuration

Change Settings

Selects an optimal setting for the Super IO device.

Serial Port FIFO Mode

The options are 16-Byte FIF0, 32-Byte FIF0, 64-Byte FIF0 and 128-Byte FIF0.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 3 Conguration

Serial Port

Device Settings

Change Settings Serial Port FIFO Mode

[Enabled]

IO=3E8h; IRQ=10;

[Auto] [128-Byte FIFO]

Serial Port 4 Configuration

Change Settings

Selects an optimal setting for the Super IO device.

Serial Port FIFO Mode

The options are 16-Byte FIF0, 32-Byte FIF0, 64-Byte FIF0 and 128-Byte FIF0.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 4 Conguration

Serial Port

Device Settings

Change Settings Serial Port FIFO Mode

[Enabled]

IO=2E8h; IRQ=10;

[Auto] [128-Byte FIFO]

60

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

SmartFAN Configuration

This section is used to configure the fan settings.

CPUFAN Type

Configures the CPU fan type to 3-pin or 4-pin.

CPUFAN Smart Mode

Enables of disables CPU fan smart mode. When enabled, the following submenus are available:

CPUFan Full-Speed Temperature

Configures the temperature threshold of full speed. Fan will activate at full speed when temperature threshold is exceeded.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

SmartFAN Conguration

CPUFAN Type

CPUFAN Smart Mode CPUFAN Full-Speed Temperature CPUFAN Full-Speed Duty CPUFAN Idle-Speed Temperature CPUFAN Idle-Speed Duty

[3-Pin]

[Enabled] 75 100 40 40

CPUFan Full-Speed Duty

Configures the pre-set duty threshold of full speed. Fan will activate at full speed when the pre-set duty is exceeded.

CPUFan Idle-Speed Temperature

Configures the temperature threshold of idle speed. Fan will activate at idle speed when the temperature is below the threshold.

CPUFan Idle-Speed Duty

Configures the pre-set duty threshold of idle speed. Fan will activate at idle speed when the pre-set duty is below the threshold.

61

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

PC Health Status

CPU Temperature System Temperature CPUFAN Speed VCORE VCC +12V VDIMM VCC3V VSB3V VBAT

: +59 C : +67 C : 0 RPM : +0.808 V : +5.120 V : +12.144 V : +1.375 V : +3.408 V : +3.408 V : +3.280 V

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Shutdown Temperature

[Disabled]

PC Health Status

This section is used to monitor hardware status such as temperature, fan speed and voltages.

Shutdown Temperature Configuration

This section is used to configure the temperature to shutdown the system.

CPU Temperature

Detects and displays the current CPU temperature.

System Temperature

Detects and displays the current system temperature.

CPUFAN Speed

Detects and displays the CPU fan speed.

VCORE to VBAT

Detects and displays the output voltages.

Shutdown Temperature

Sets the temperature to shutdown the system.

62

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Serial Port Console Redirection

This section is used to configure serial port console redirection settings.

Console Redirection

Enables or disables the console redirection. When enabled, Console Redirection Settings will be available.

Console Redirection (Serial Port for Out-of-Band Management)

Enables or disables the console redirection. When enabled, Console Redirection Settings will be available.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Console Redirection Enable or Disable

COM1

Console Redirection

Console Redirection Settings

Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS)

Console Redirection

Console Redirection Settings

[Disabled]

►

Console Redirection Settings

Specifies how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.

COM1

Console Redirection Settings

Terminal Type

Bits per second Data Bits Parity Stop Bits Flow Control VT-UTF8 Combo Key Sup Recorder Mode Resolution 100x31 Legacy OS Redirection Resolution Putty KeyPad Redirection After BIOS POST

[ANSI]

[115200] [8] [None] [1] [None] [Enabled] [Disabled] [Disabled] [80x24] [VT100] [Always Enable]

Terminal Type

ANSI Extended ASCII character set. VT100 ASCII character set. VT100+ Extends VT100 to support color, function keys, etc. VT-UTF8 Uses UTF8 encoding to map Unicode characters onto 1 or more bytes.

63

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Bits Per Second

Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed.

Data Bits

The options are 7 and 8.

Parity

A parity bit can be sent with the data bits to detect some transmission erros.

Even Parity bit is 0 if the number of 1’s in the data bits is even. Odd Parity bit is 0 if number of 1’s in the data bits is odd.

Stop Bits

Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit.

Flow Control

Flow control can prevent data loss from buffer overflow. When sending data and the receiving buffers are full, a “stop” signal can be sent to stop the data flow.

VT-UTF8 Combo Key Support

Enables or disables VT-UTF8 combination key support for ANSI/VT100 terminals.

Recorder Mode

When this field is enabled, only text will be sent. This is to capture the terminal data.

Resolution 100x31

Enables or disables extended terminal resolution.

Legacy OS Redirection Resolution

Selects the number of rows and columns that support redirection.

Putty KeyPad

Selects the Putty keyboard emulation type.

Redirection After BIOS POST

The settings specify if BootLoader is selected, then Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy Console Redirection is enabled for Legacy OS.

64

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Console Redirection Settings (Serial Port for Out-of-Band Management)

Specifies how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.

Out-of-Band Mgmt Port

Terminal Type

Bits per second Flow Control

Data Bits Parity Stop Bits

COM1

[VT-UTF8]

[115200] [None]

8 None 1

Terminal Type

ANSI Extended ASCII character set. VT100 ASCII character set. VT100+ Extends VT100 to support color, function keys, etc. VT-UTF8 Uses UTF8 encoding to map Unicode characters onto 1 or more bytes.

Bits Per Second

Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed.

Flow Control

Flow control can prevent data loss from buffer overflow. When sending data and the receiving buffers are full, a “stop” signal can be sent to stop the data flow.

65

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

CPU Configuration

This section is used to configure the CPU.

Exit

Advanced Chipset PCIPnP Security

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Disabled for Windows XP

CPU Conguration

Intel(R) Celeron(R) CPU N2807 @ 1.58GHz CPU Signature 30678 Microcode Patch 815 Max CPU Speed 1580 MHz

Min CPU Speed 500 MHz Processor Cores 2 Intel HT Technology Not Supported Intel VT-x Technology Supported

L1 Data Cache 24 kB x 2 L1 Code Cache 32 kB x 2 L2 Cache 1024 kB x 1 L3 Cache Not Present 64-bit Supported

Limit CPUID Maximum [Disabled]

Execute Disable Bit [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetch [Enabled] Intel Virtualization Technology [Disabled] Power Technology [Energy Efficient]

Limit CPUID Maximum

The CPUID instruction of some newer CPUs will return a value greater than 3. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur.

Execute Disable Bit

When this field is set to Disabled, it will force the XD feature flag to always return to 0.

Hardware Prefetcher

Turns on or off the mid level cache (L2) streamer prefetcher.

Adjacent Cache Line Prefetch

Turns on or off prefetching of adjacent cache lines.

Intel® Virtualization Technology

When this field is set to Enabled, the VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

Power Technology

Enables or disables the power management features.

66

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

CPU PPM Configuration

This section is used to configure the Processor Power Management (PPM) configuration.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable/Disable Intel SpeedStep

PPM Conguration

EIST

CPU C state Report Enhanced C state Max CPU C-state

[Enabled]

[Enabled] [Enabled] [ C7]

EIST

Enables or disables Intel® SpeedStep.

CPU C State Report

Enables or disables CPU C-State report to OS.

Enhanced C State

Enables or disables enhanced C-State.

Max CPU C-state

This option controls the max C-State that the processor will support.

Advanced Boot Security Save & ExitMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable / Disable Serial ATA

SATA Conguration

SATA Port

SATA Mode SATA Speed Support SATA Port1 mSATA/SATA Port2

SATA Port TS64GSSD320 (64.0GB)

mS ATA Not Present

[Enabled]

[AHCI Mode] [Gen2] [Enabled] [Enabled]

SATA Configuration

This section is used to configure the SATA drives.

SATA Port

Enables or disables the SATA port.

SATA Mode

IDE This option configures the Serial ATA drives as Parallel ATA physical storage device.

AHCI This option configures the Serial ATA drives to use AHCI (Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.

67

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

SATA Speed Support

Configures the speed of the SATA controller.

SATA Port1

Enables or disables SATA port1.

mSATA/SATA Port2

Enables or disables mSATA/SATA port2.

Advanced Boot Security Save & ExitMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable/Disable UEFI Network Stack

Network Stack

[Disabled]

Network Stack Configuration

This section is used to configure the network stack settings.

Network Stack

Enables or disables UEFI network stack.

68

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Advanced Boot Security Save & ExitMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set display mode for Option ROM

Compatibility Support Module Conguration

Option ROM Messages

INT19 Trap Response

Option ROM execution order

Network Storage Other PCI devices

[Force BIOS]

[Immediate]

[Do not launch] [Legacy only]

[UEFI rst]

CSM Configuration

This section is used to configure the compatibility support module features.

Option ROM Messages

Selects the display mode for Option ROM. The options are Force BIOS and Keep Current.

INT19 Trap Response

Allows Option ROMs to trap Interrupt 19 when enabled.

Immediate Execute the trap right away. Postponed Execute the trap during legacy boot.

Network

Enables or disables the boot option for legacy network devices.

Storage

Enables or disables the boot option for legacy storage devices.

Other PCI Devices

Enables or disables the boot option for legacy PCI devices.

69

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

USB Conguration

USB Devices: 1 Keyboard, 1 Mouse, 3 Hubs

Legacy USB Support

XHCI Hand-off EHCI Hand-off USB Mass Storage Driver Support

USB hardware delays and time-outs:

USB transfer time-out Device reset time-out Device power-up delay

[Enabled]

[Enabled] [Disabled] [Enabled]

[20 sec] [20 sec] [Auto]

Legacy USB Support

Enabled Enables Legacy USB. Auto Disables support for Legacy when no USB devices are connected. Disabled Keeps USB devices available only for EFI applications.

XHCI Hand-off

This is a workaround for OSs that does not support XHCI hand-off. The XHCI ownership change should be claimed by the XHCI driver.

USB Configuration

This section is used to configure the USB.

EHCI Hand-off

This is a workaround for OSs that does not support EHCI hand-off. The EHCI ownership change should be claimed by the EHCI driver.

USB Mass Storage Driver Support

Enables or disables USB mass storage driver support.

USB Transfer Time-out

The time-out value for control, bulk, and Interrupt transfers.

Device Reset Time-out

Selects the USB mass storage device’s start unit command timeout.

Device Power-up Delay

Maximum time the value will take before it properly reports it self to the Host Controller. “Auto” uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.

70

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Driver Information Driver Name: Driver Version: Driver Released Date:

Device Information Device Name: PCI Slot: MAC Address:

Patent Information This product is covered by one or US6,570,884, US6,115,776, and US6,

Realtek UEFI UNDI Driver

2.024 2013/10/15

Realtek PCIe GbE Family 03:00:00 00:30:18:C3:F8:79

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Driver Information Driver Name: Driver Version: Driver Released Date:

Device Information Device Name: PCI Slot: MAC Address:

Patent Information This product is covered by one or US6,570,884, US6,115,776, and US6,

Realtek UEFI UNDI Driver

2.024 2013/10/15

Realtek PCIe GbE Family 04:00:00 00:30:18:C3:F8:7A

Realtek PCIe GbE Family Controller

Displays the driver information of the Ethernet controller 1.

Realtek PCIe GbE Family Controller

Displays the driver information of the Ethernet controller 2.

71

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Chipset

This section gives you functions to configure the system based on the specific features of the chipset. The chipset manages bus speeds and access to system memory resources.

North Bridge

Enters the North Bridge submenu.

South Bridge

Enters the South Bridge submenu.

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

North Bridge Parameters

North Bridge

South Bridge

►

North Bridge

Save & Exit

Advanced

Chipset Boot SecurityMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enable : Enable IGD Turbo Enable. Disable: IGD Turbo Disable

Memory Information Total Memory Memory Current Frequency

Intel IGD Conguration

IGD Turbo Enable

Spread Spectrum clock

IGD Boot Type Active LVDS LVDS Panel Type

2048 MB 1333 Mhz

[Enabled]

[Disabled]

[LVDS] [Enabled] [1920x1080 24bit Dual ]

IGD Turbo Enable

Enables or disables IGD turbo.

Spread Spectrum Clock

Enables or disables spread spectrum clock.

IGD Boot Type

Selects the video device that will be activated during POST. This will not affect any external graphics that may be present.

Active LVDS

Enables or disables LVDS.

LVDS Panel Type

Configures the LVDS display resolution.

72

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

South Bridge

MMPE Slot Speed

Configures the MMPE slot speed. The options are Auto, Gen2 and Gen1.

MPE Controller

Enables or disables the MPE controller.

Speed

Configures the MPE controller speed.

Onboard Lan1 to Lan2 Controller

Enables or disables the onboard Lan1 or Lan2 controller.

Restore AC Power Loss

Select the AC power state when power is re-applied after a power failure.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Azalia HD Audio Options

Azalia HD Audio

USB Conguration

MMPE Slot Speed MPE Controller Speed Onboard Lan1 Controller Onboard Lan2 Controller

Restore AC Power Loss

[Auto] [Enabled] [Auto] [Enabled] [Enabled]

[Power Off]

►

Azalia HD Audio

Azalia

Control detection of the Azalia device.

Disabled Azalia will be unconditionally Disabled. Enabled Azalia will be unconditionally Enabled.

Azalia HDMI Codec

Enables or disables internal HDMI codec for Azalia.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled Enabled = Azalia will be unconditionally Enabled Auto = Azalia will be enabled if present disabled otherwise.

Audio Conguration

Audio Controller

Azalia HDMI Codec

[Enabled]

73

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

USB Configuration

USB 3.0 Support

Enables or disables the USB 3.0 controller.

USB 3.0 Link Power Management

Enables or disables USB 3.0 link power management.

Chipset

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Control the USB 3.0 functions

USB Conguration

USB 3.0 Support

USB 3.0 Link Power Management

USB 2.0 Support

[Auto]

[Enabled]

[Disabled]

Security

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Set Administrator Password

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User Will have Administrator rights. The password length must be in the following range: Minimum length 3 Maximum length 20

Administrator Password

User Password

Administrator Password

Select this to reconfigure the administrator’s password.

User Password

Select this to reconfigure the user’s password.

74

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Boot

This section is used to configure the boot features.

Setup Prompt Timeout

Selects the number of seconds to wait for the setup activation key. 65535(0xFFFF) denotes indefinite waiting.

Bootup NumLock State

This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.

Save & Exit

Advanced Chipset

Security

BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Number of seconds to wait for setup activation key.

65535(0xFFFF) means indenite

waiting.

Boot Conguration

Setup Prompt Timeout

Bootup NumLock State

Quiet Boot

Boot Option Priorities

Boot Option #1 Boot Option #2

Hard Drive BBS Priorities

[Off]

[Enabled]

[P0: TS64GSSD320 . . .] [UEFI: Built-in EFI . . .]

Quiet Boot

Enabled Displays OEM logo instead of the POST messages. Disabled Displays normal POST messages.

Boot Option Priorities

Adjust the boot sequence of the system. Boot Option #1 is the first boot device that the system will boot from, next will be #2 and so forth.

Hard Drive BBS Priorities

Sets the order of the legacy devices in this group.

2

75

TPPC 2210 and TPPD 2200 Series User Manual

Chapter 4: BIOS Setup

Save & ExitAdvanced Chipset Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Reset the system after saving the changes.

Save Changes and Reset

Discard Changes and Reset

Restore Defaults Save as User Defaults Restore User Defaults

Boot Override

UEFI: Built-in EFI Shell P0: TS64GSSD320

Launch EFI Shell from lesystem device

Reset System with TXE disable Mode

Save & Exit

Save Changes and Reset

To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Discard Changes and Reset

To exit the Setup utility and reboot the system without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting.

Restore Defaults

To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Save as User Defaults

To use the current configurations as user default settings for the BIOS, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Restore User Defaults

To restore the BIOS to user default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Boot Override

To bypass the boot sequence from the Boot Option List and boot from a particular device, select the desired device and press <Enter>.

Launch EFI Shell from filesystem device

To launch EFI shell from a filesystem device, select this field and press <Enter>.

Reset System with TXE Disable Mode

To restart the system and boot with TXE disabled, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

►

76

TPPC 2210 and TPPD 2200 Series User Manual

Appendix A: Watchdog

aPPendIx a: WatChdog

WDT Device Configuration Registers (LDN CR07)

Watchdog Control Configuration Register 1 - Index F5h

Bit Name R/W Reset Default Description

7 Reserved R - 0 Reserved

6 WDTMOUT_STS R/W 5VSB 0

If watchdog timeout event occurred, this bit will be set to 1. Write a 1 to this bit will clear it to 0.

5 WD_EN R/W 5VSB 0

If this bit is set to 1, the counting of watchdog time is enabled.

4 WD_PULSE R/W 5VSB 0

Select output mode (0: level, 1: pulse) of RSTOUT# by setting this bit.

3 WD_UNIT R/W 5VSB 0

Select time unit (0: 1sec, 1: 60 sec) of watchdog timer by setting this bit.

2 WD_HACTIVE R/W 5VSB 0

Select output polarity of RSTOUT# (1: high active, 0: low active) by setting this bit.

1-0 WD_PSWIDTH R/W 5VSB 0

Select output pulse width of RSTOUT# 0: 1ms 1: 25ms 2: 125ms 3: 5 sec

77

TPPC 2210 and TPPD 2200 Series User Manual

Appendix A: Watchdog

Watchdog Timer Configuration Register 2 - Index F6h

Bit Name R/W Reset Default Description

7-0 WD_TIME R/W 5VSB 0 Time of watchdog timer (0 ~ 255)

Watchdog PME Enable Configuration Register 2 - Index FAh

Bit Name R/W Reset Default Description

7 WDT_PME R 5VSB 0

0: No WDT PME occurred. 1: WDT PME occurred. The WDT PME is occurred one unit before WDT timeout.

6 WDT_PME_EN R/W 5VSB 0

0: Disable Watchdog PME. 1: Enable Watchdog PME.

5 Reserved R - 0 Reserved

4 WDT_CLK_SEL R/W 5VSB 1

WDT Clock Source Select 0: Internal 1KHz clock. 1: 1KHz clock driven by CLKIN.

3-1 Reserved R - 0 Reserved

0 WDOUT_EN R/W 5VSB 0

0: Disable Watchdog time-out output via WDTRST# 1: Enable Watchdog time-out output via WDTRST#