Nexcom NSA 5160, NI 140F, NX 140F, NI 142C, NI 180C User Manual

NEXCOM International Co., Ltd.

Published July 2016

www.nexcom.com

Network and Communication Solutions

Network Security Appliance NSA 5160

User Manual

ii

NSA 5160 BIOS Manual

Content

Contents

Preface

Copyright ............................................................................................. iv

Disclaimer .............................................................................................. iv

Acknowledgements ............................................................................... iv

Regulatory Compliance Statements ........................................................ iv

Declaration of Conformity ...................................................................... iv

RoHS Compliance ................................................................................... v

Warranty and RMA ................................................................................ vi

Safety Information ................................................................................viii

Installation Recommendations ...............................................................viii

Safety Precautions .................................................................................. ix

Technical Support and Assistance ............................................................ x

Conventions Used in this Manual ............................................................ x

Global Service Contact Information ........................................................ xi

Package Contents .................................................................................xiii

Ordering Information ............................................................................xiv

Chapter 1: Product Introduction

Overview ................................................................................................1

Key Features ...........................................................................................1

Hardware Specifications ..........................................................................2

Knowing Your NSA 5160 ........................................................................ 3

Front Panel ..........................................................................................3

Rear Panel ...........................................................................................4

Chapter 2: Jumpers and Connectors

Before You Begin ....................................................................................5

Precautions ............................................................................................5

Jumper Settings ......................................................................................6

Locations of the Jumpers and Connectors ...............................................7

Jumpers ..................................................................................................8

RTC Clear ............................................................................................ 8

ME Firmware Update ...........................................................................8

BIOS Recovery Swap ............................................................................9

TPM Select Pin Header .........................................................................9

Console CTS Strap Pin Header ...........................................................10

BMC Strap .........................................................................................10

Console UART Controller Strap ..........................................................11

Connector Pin Definitions .....................................................................12

External I/O Interfaces ........................................................................ 12

Reset Button ..................................................................................12

RS232 Console and Dual USB 2.0 Port ...........................................12

Connector Pin Definitions .....................................................................13

Internal Connectors ........................................................................... 13

Power Button .................................................................................13

CPLD JTAG Pin Header ...................................................................13

USB 3.0 Box Header .......................................................................14

SATA DOM Power Connector .........................................................14

System Fan Connector ...................................................................15

VGA Connector .............................................................................15

LCM JST Connector ........................................................................16

iii

NSA 5160 BIOS Manual

Content

ATX Power Connector ....................................................................16

ATX Power Connector ....................................................................17

Block Diagram ......................................................................................18

Chapter 3: System Setup

Removing the Chassis Cover .................................................................19

Installing a SATA DOM ..........................................................................20

Installing DIMM Memory Modules ........................................................23

Installing a 2.5” SATA Hard Drive ..........................................................24

Installing a LAN Module ........................................................................28

Chapter 4: BIOS Setup

About BIOS Setup .................................................................................30

When to Configure the BIOS .................................................................30

Default Configuration ...........................................................................31

Entering Setup ......................................................................................31

Legends ................................................................................................31

BIOS Setup Utility ..................................................................................33

Main .................................................................................................33

Advanced .........................................................................................34

Intel RC Setup ..................................................................................44

Server Mgmt .....................................................................................55

Security .............................................................................................59

Boot ..................................................................................................60

Save & Exit ........................................................................................61

iv

NSA 5160 User Manual

Preface

PrefaCe

Copyright

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.

Disclaimer

The information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom.com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.

Acknowledgements

NSA 5160 is a trademark of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and describes how to keep the system CE compliant.

Declaration of Conformity

FCC

This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense.

CE

The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.

v

NSA 5160 User Manual

Preface

RoHS Compliance

NEXCOM RoHS Environmental Policy and Status Update

NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green

products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2011/65/EU, to be your trusted green partner and to protect our environment.

RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <

0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm.

In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products. The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned.

The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.

How to recognize NEXCOM RoHS Products?

For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name.

All new product models launched after January 2013 will be RoHS compliant. They will use the usual NEXCOM naming convention.

vi

NSA 5160 User Manual

Preface

Warranty and RMA

NEXCOM Warranty Period

NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM. HCP series products (Blade Server) which are manufactured by NEXCOM are covered by a three year warranty period.

NEXCOM Return Merchandise Authorization (RMA)

▪ Customers shall enclose the “NEXCOM RMA Service Form” with the

returned packages.

▪ Customers must collect all the information about the problems

encountered and note anything abnormal or, print out any on-screen messages, and describe the problems on the “NEXCOM RMA Service Form” for the RMA number apply process.

▪ Customers can send back the faulty products with or without accessories

(manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, NEXCOM is not responsible for the devices/parts.

▪ Customers are responsible for the safe packaging of defective products,

making sure it is durable enough to be resistant against further damage and deterioration during transportation. In case of damages occurred during transportation, the repair is treated as “Out of Warranty.”

▪ Any products returned by NEXCOM to other locations besides the

customers’ site will bear an extra charge and will be billed to the customer.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

Repair Service Charges for Out-of-Warranty Products

NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee.

System Level

▪ Component fee: NEXCOM will only charge for main components such as

SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistor, capacitor.

▪ Items will be replaced with NEXCOM products if the original one cannot

be repaired. Ex: motherboard, power supply, etc.

▪ Replace with 3rd party products if needed.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

Board Level

▪ Component fee: NEXCOM will only charge for main components, such

as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistors, capacitors.

▪ If RMA goods can not be repaired, NEXCOM will return it to the customer

without any charge.

vii

NSA 5160 User Manual

Preface

Warnings

Read and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements.

Cautions

Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

viii

NSA 5160 User Manual

Preface

Installation Recommendations

Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated.

Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:

▪ A Philips screwdriver

▪ A flat-tipped screwdriver

▪ A grounding strap

▪ An anti-static pad

Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

Safety Information

Before installing and using the device, note the following precautions:

▪ Read all instructions carefully.

▪ Do not place the unit on an unstable surface, cart, or stand.

▪ Follow all warnings and cautions in this manual.

▪ When replacing parts, ensure that your service technician uses parts

specified by the manufacturer.

▪ Avoid using the system near water, in direct sunlight, or near a heating

device.

▪ The load of the system unit does not solely rely for support from the

rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability.

▪ The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.

ix

NSA 5160 User Manual

Preface

Safety Precautions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a

damp cloth. Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the

equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a stable surface during installation. Dropping it or

letting it fall may cause damage.

7. The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting

the equipment to the power outlet.

9. Place the power cord in a way so that people will not step on it. Do not

place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work

according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage.

15. Do not place heavy objects on the equipment.

16. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet.

17. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

x

NSA 5160 User Manual

Preface

Technical Support and Assistance

1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com.

2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling: – Product name and serial number – Detailed information of the peripheral devices – Detailed information of the installed software (operating system,

version, application software, etc.) – A complete description of the problem – The exact wordings of the error messages

Warning!

1. Handling the unit: carry the unit with both hands and handle it with care.

2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth.

3. CompactFlash: Turn off the unit’s power before inserting or removing a CompactFlash storage card.

Conventions Used in this Manual

Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.

CAUTION!

CAUTION!CAUTION!

Caution: Information to avoid damaging components or losing data.

Note: Provides additional information to complete a task easily.

xi

NSA 5160 User Manual

Preface

Global Service Contact Information

Headquarters

NEXCOM International Co., Ltd.

9F, No. 920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7786 Fax: +886-2-8226-7782 www.nexcom.com

America

USA NEXCOM USA

2883 Bayview Drive, Fremont CA 94538, USA Tel: +1-510-656-2248 Fax: +1-510-656-2158 Email: [email protected] www.nexcom.com

Asia

Taiwan NEXCOM Intelligent Systems

Taipei Office

13F, No.920, Chung-Cheng Rd., ZhongHe District, New Taipei City, 23586, Taiwan, R.O.C. Tel: +886-2-8226-7796 Fax: +886-2-8226-7792 Email: [email protected] www.nexcom.com.tw

NEXCOM Intelligent Systems Taichung Office

16F, No.250, Sec. 2, Chongde Rd., Beitun Dist., Taichung City 406, R.O.C. Tel: +886-4-2249-1179 Fax: +886-4-2249-1172 Email: [email protected] www.nexcom.com.tw

Japan NEXCOM Japan

9F, Tamachi Hara Bldg., 4-11-5, Shiba Minato-ku, Tokyo, 108-0014, Japan Tel: +81-3-5419-7830 Fax: +81-3-5419-7832 Email: [email protected] www.nexcom-jp.com

China

NEXCOM China

1F & 2F, Block A, No. 16 Yonyou Software Park, No. 68 Beiqing Road, Haidian District, Beijing, 100094, China Tel: +86-10-5704-2680 Fax: +86-10-5704-2681 Email: [email protected] www.nexcom.cn

xii

NSA 5160 User Manual

Preface

Europe

United Kingdom NEXCOM EUROPE

10 Vincent Avenue, Crownhill Business Centre, Milton Keynes, Buckinghamshire MK8 0AB, United Kingdom Tel: +44-1908-267121 Fax: +44-1908-262042 Email: [email protected] www.nexcom.eu

Italy NEXCOM ITALIA S.r.l

Via Lanino 42, 21047 Saronno (VA), Italia Tel: +39 02 9628 0333 Fax: +39 02 9625 570 Email: [email protected] www.nexcomitalia.it

NEXCOM Shanghai

Room 603/604, Huiyinmingzun Plaza Bldg., 1, No.609, Yunlin East Rd., Shanghai, 200333, China Tel: +86-21-5278-5868 Fax: +86-21-3251-6358 Email: [email protected] www.nexcom.cn

NEXCOM Surveillance Technology

Room 209, Floor 2 East, No.2, Science & Technology industrial park of privately owned enterprises, Xili, Nanshan Dist., Shenzhen, 518055, China Tel: +86-755-8364-7768 Fax: +86-755-8364-7738 Email: [email protected] www.nexcom.cn

NEXCOM United System Service

Hui Yin Ming Zun Building Room 1108, Building No. 11, 599 Yunling Road, Putuo District, Shanghai, 200062, China Tel: +86-21-6125-8282 Fax: +86-21-6125-8281 Email: [email protected] www.nexcom.cn

xiii

NSA 5160 User Manual

Preface

Package Contents

Before continuing, verify that the NSA 5160 package that you received is complete. Your package should have all the items listed in the following table.

Item Part Number Name Description Qty

1 19S00516000X0 NSA 5160 ASSY 1 2 5044440031X00 Rubber Foot Kang Yang: RF20-5-4P 19.8 x 18 x 5.0mm 4 3 6012200052X00 PE Zipper Bag #8 170 x 240mm, w/China RoHS Symbol 1 4 6012200053X00 PE Zipper Bag #3 100 x 70mm, w/China RoHS Symbol 1 5 6023309081X00 Cable EDI: 232091081804-RS COM Port. DB9 Female to RJ45 8P8C L:1800mm 1 6 50311F0102X00 (H)Round Head Screw Long Fei:P6#32T x 1/4/SW7*0.8 W/Spring + Flat Washer P6#32T x 1/4/SW7 x 0.8 NI 4 7 603ATA0052X00 SATA Cable ST:MD-6104042 SATA 7P 180D (Lock) to 7P 90D (Lock) L=260mm 1 8 5060900301X00 NSA 5130 Ear Sets VER:A CHYUAN-JYH 79.5 x 43.5 x 26mm AL PANTONE 295U 1 9 50311F0100X00 (H)Round Head Screw w/Spring+Flat Washer Long Fei:P3 x 6L P3 x 6 iso/SW6 x 0.5 NI 1

10 5040150001X00 NSA 7135 AL Handle VER:A PANADVANCE 78 x 58 x 8mm 1

xiv

NSA 5160 User Manual

Preface

Ordering Information

The following below provides ordering information for NSA 5160.

Barebone NSA 5160 (P/N: 10S00516000X0)

1U Intel® Xeon® processor D-1520 4C/2.2Ghz with 2x 10GbE + 8 1GbE LAN ports, 2 LAN module (NI/NX series) bays, w/o LCM kit

NX 140F

Intel® XL710-AM1 10GbE module 4 fiber ports by PCIe x8 interface with PKG

NX 142F

Intel® XL710-AM1 10GbE module 4 fiber ports with 2 bypass segment (multi mode) by PCIe x8 interface with PKG

NI 140F

Intel® I350 module 4 fiber ports with PCIe x8 interface with PKG

NI 180F

Intel® I350 module 8 fiber ports with PCIe x8 interface with PKG

NI 142C

Intel® I350 module 4 copper ports with 2 bypass segment by PCIe x8 interface with PKG

NI 180C

Intel® I350 module 8 copper ports by PCIe x8 interface with PKG

NI 184C

Intel® I350 module 8 copper ports with 4 bypass segment by PCIe x8 interface with PKG

NI 142F

Intel® I350 module 4 fiber ports with 2 bypass segment by PCIe x8 interface with PKG

NI 121F

Intel® I350 module 2 fiber ports with 1 bypass segment by PCIe x8 interface with PKG

xv

NSA 5160 User Manual

Preface

Model P/N Controller Interface Type Port Number Bypass/Segment Expansion Slot Location Slot

NX 140F 10S20140F01X0 XL710-AM1 PCIe x8 4 SFP+ None None All Slot

NX 142F 10S20142F01X0 XL710-AM1 PCIe x8 4 SFP+

2 bypass

(multi mode)

None All Slot

NI 140F 10SK000NI02X0 i350AM4x1 PCIe x8 4 SFP None None All Slot

NI 180F 10S10180F01X0 i350AM4x2 PCIe x8 8 SFP None None All Slot

NI 142C 10SK000NI03X0 i350AM4x1 PCIe x8 4 Copper 2 bypass None All Slot

NI 180C 10S10180C01X0 i350AM4x2 PCIe x8 8 Copper None None All Slot

NI 184C 10S10184C01X0 i350AM4x2 PCIe x8 8 Copper 4 bypass None All Slot

NI 142F 10S10142F01X0 i350AM4x1 PCIe x8 4 SFP 2 bypass None All Slot

NI 121F 10S10121F01X0 i350AM2x1 PCIe x8 4 SFP 1 bypass None All Slot

1

NSA 5160 User Manual

Chapter 1: Product Introduction

ChaPter 1: ProduCt IntroduCtIon

Key Features

▪ 1U rackmount network platform

▪ Intel

®

Xeon® processor D-1500 product family

▪ Support DDR4 2133 ECC & REG, up to 128GB

Overview

▪ Onboard 8G LAN Copper + 2 x 10G SFP+

▪ Support up to two LAN modules

2

NSA 5160 User Manual

Chapter 1: Product Introduction

Hardware Specifications

Main Board

▪ NSB 5160 ▪ Intel® Xeon® processor D-1500 product family ▪ CS4227 10G PHY ▪ Support IPMI 2.0 (option) ▪ One PCIe x8 expansion slot

Main Memory

▪ 4x DDR4 2133 memory DIMM support ECC/Non-ECC memory,

max 128GB

LAN Features

▪ Swappable LAN modules

** Please see LAN module list in Ordering Information.

▪ Support Intel® i350/Intel® XL710 Copper/Fiber ports ▪ Support 10/100/1000/10G link speed

I/O Interface-Front

▪ Power status/HDD status/LAN status/Bypass status LEDs ▪ 2x USB 2.0 ports ▪ 1x RJ45 type console port ▪ 2x SFP + ports ▪ 8x Copper LAN ports ▪ 2x LAN modules

I/O Interface-Rear

▪ 1x Power button switch ▪ 1x VGA port

Devices

▪ 1x SATA-DOM device space

Power Input

▪ 300W switching power supply

Chassis Dimensions

▪ Chassis dimension: 430mm x 450mm x 44mm ▪ Carton dimension: 560mm x 620mm x 190mm

Weight

▪ Without packing: 8kg ▪ With packing: 12kg

Environment

▪ Operating temperatures : 0°C~40°C ▪ Storage temperature : -20°C~75°C ▪ Relative humidity : 10%~90% non-condensing

Certifications

▪ CE approval ▪ FCC Class A ▪ UL

3

NSA 5160 User Manual

Chapter 1: Product Introduction

Knowing Your NSA 5160

LCD

SFP ports

Front Panel

USB ports

RJ45 type

console port

LCD

LCD display with serial data interface.

Reset Button

Press to restart the system.

Power LED

Indicates the power status of the system.

HDD LED

Indicates the status of the hard drive.

RJ45 Type Console Serial Port

Used to connect RJ45 type console devices.

USB Ports

Used to connect USB 2.0 devices.

SFP Ports

Used to connect SFP modules for connecting fiber optic network devices.

Copper LAN Ports

Eight LAN ports used to connect network devices.

LAN Modules

Two LAN module bays to install add-on network modules.

Reset button

Power/HDD LEDs

LAN modulesCopper LAN ports

4

NSA 5160 User Manual

Chapter 1: Product Introduction

Rear Panel

AC Power Socket Power Switch

Expansion slot

(optional)

Expansion Slot (Optional)

Used to install a PCI Express add-on card.

VGA

Used to connect an analog VGA monitor.

AC Power Socket

Plug an AC power cord here before turning on the system.

Power Switch

Press to power-on or power-off the system.

VGA

5

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

ChaPter 2: JumPers and ConneCtors

This chapter describes how to set the jumpers and connectors on the NSA 5160 motherboard.

Before You Begin

▪ Ensure you have a stable, clean working environment. Dust and dirt can

get into components and cause a malfunction. Use containers to keep small components separated.

▪ Adequate lighting and proper tools can prevent you from accidentally

damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: – A Philips screwdriver – A flat-tipped screwdriver – A set of jewelers screwdrivers – A grounding strap – An anti-static pad

▪ Using your fingers can disconnect most of the connections. It is

recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.

▪ Before working on internal components, make sure that the power is off.

Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the electronic components. Humid environments tend to have less static electricity than

dry environments. A grounding strap is warranted whenever danger of static electricity exists.

Precautions

Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous.

Follow the guidelines below to avoid damage to your computer or yourself:

▪ Always disconnect the unit from the power outlet whenever you are

working inside the case.

▪ If possible, wear a grounded wrist strap when you are working inside the

computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.

▪ Hold electronic circuit boards by the edges only. Do not touch the

components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.

▪ Leave all components inside the static-proof packaging that they shipped

with until they are ready for installation.

▪ Use correct screws and do not over tighten screws.

6

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Jumper Settings

A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open.

Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).

Two-Pin Jumpers: Open (Left) and Short (Right)

Three-Pin Jumpers: Pins 1 and 2 are Short

1

2

3

1

2

3

7

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Locations of the Jumpers and Connectors

The figure below shows the location of the jumpers and connectors.

71

1

2

4

1

B49

B12

B11

B1

B49

B12

B11

B1

1313131312121

2

1

6

3

1

915

16 10

85

41

17

1717

1

11 10

19

12

24

1

13

58

1

4

16131

2

A32 A31 B31 B32B2

B1

A1

A2

260

159

4

1

2

15

16

2

1

2

1

31313

1

U68

JP3

JP11J4

J8

J10

LED15

U49

SATA4

SATA3SATA2

SATA1

JP8

JP6

JP10

D5

U7

J3

J2

J1

JP4

JP5J7J6

J5

JP7

J11

CN1

SW21

J9

JUSB1

CON1

CON2

JP9

JTPMSEL1

JPWRBTN1

VGACONN1

FAN2

FAN1

8

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Jumpers

RTC Clear

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: J5

ME Firmware Update

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: J6

1 3 1 3

Pin Function

1-2 Disable ME Force Update 2-3 ME Force Update

1-2 On: default

Pin Function

1-2 Normal 2-3 Clear CMOS

1-2 On: default

9

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

BIOS Recovery Swap

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: J7

1 3

Pin Function

1-2 Disable BIOS_Recovery Mode 2-3 Enable BIOS_Recovery Mode

1-2 On: default

TPM Select Pin Header

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JTPMSEL1

1 3

Pin Function

1-2 Enable Some Special Commands 2-3 Disable Some Special Commands

2-3 On: default

10

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Console CTS Strap Pin Header

Connector type: 1x3 3-pin header, 2.54mm pitch Connector location: JP7

BMC Strap

Connector type: 1x2 2-pin header, 2.54mm pitch Connector location: JP5

1 3

Pin Function

1-2 RTS to CTS 2-3 CTS

2-3 On: default

Pin Function

NC Enable BMC 1-2 Disable BMC

NC: default

12

11

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Console UART Controller Strap

Connector type: 1x2 2-pin header, 2.54mm pitch Connector location: JP4

Pin Function

NC System UART Controller 1-2 BMC Debug UART Controller

NC: default

12

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

External I/O Interfaces

Reset Button

Connector location: SW21

Pin Definition

1 GND 2 RST_BTN_N

1 2

RS232 Console and Dual USB 2.0 Port

Connector type: RJ45 port and USB 2.0 ports, Type A Connector location: CN1

RS232 Console

Pin Definition Pin Definition

1 SP_RTS1_R 2 SP_DTR1_R 3 SP_TXD1_R 4 GND 5 SP_DCD1_R 6 SP_RXD1_R 7 SP_DSR1_R 8 SP_CTS1_CON

USB

Pin Definition Pin Definition

1 VCC5 2 USB 2N 3 USB 2P 4 GND 5 VCC5 6 USB 1N 7 USB 1P 8 GND

8 1

1

5 8

4

13

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Connector Pin Definitions

Internal Connectors

Power Button

Connector type: 1x2 2-pin header Connector location: JPWRBTN1

Pin Definition

1 GND 2 PWRBTN

CPLD JTAG Pin Header

Connector type: 1x6 6-pin header Connector location: JP9

12

16

Pin Definition Pin Definition

1 P3V_STBY 2 GND 3 JTAG_ TCK 4 JTAG_TDO 5 JTAG_TDI 6 JTAG_TMS

14

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

USB 3.0 Box Header

Connector type: 2x10 20-pin header Connector location: JUSB1

Pin Definition Pin Definition

1 P5V 2 NC 3 NC 4 GND 5 NC 6 NC 7 GND 8 NC

9 NC 10 GND 11 USB2_L_DP0 12 USB2_L_DN0 13 GND 14 USB3_L_TX_P1 15 USB3_L_TX_N1 16 GND 17 USB3_L_RX_P1 18 USB3_L_RX_N1 19 P5V

2 1

20 19

SATA DOM Power Connector

Connector type: 1x2 2-pin header Connector location: J9

Pin Definition

1 P5V 2 GND

1

2

15

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

System Fan Connector

Connector type: 1x4 4-pin Wafer Connector location: FAN1 and FAN2

Pin Definition

1 GND

2 P12V

3 TACH

4 PWN

1 4

VGA Connector

Connector type: 2x8 16-pin header Connector location: VGACONN1

Pin Definition Pin Definition

1 DACROA_B 2 DACGOA_B 3 DACBOA_B 4 NC 5 GND 6 GND 7 GND 8 GND

9 VGA_VCC 10 GND 11 NC 12 AVSYNCO_B 13 AHSYNCO_B 14 AVSYNCO_B 15 DDC_CLKO_B 16 NC

1

2

15

16

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

LCM JST Connector

Connector type: 1x6 6-pin header Connector location: J11

Pin Definition Pin Definition

1 IBMC_LCM_TXD 2 IBMC_LCM_RXD 3 GND 4 P5V 5 LCM_LED_KR_N 6 LCM_LED_KG_N

16

ATX Power Connector

Connector type: 2x4 8-pin header Connector location: CON1

Pin Definition Pin Definition

1 GND 2 GND

3 GND 4 GND

5 P12V 6 P12V

7 P12V 8 P12V

1

5 8

4

17

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

ATX Power Connector

Connector type: 2x12 24-pin header Connector location: CON2

Pin Definition Pin Definition

1 3.3V 2 3.3V 3 GND 4 5V 5 GND 6 5V 7 GND 8 PW-OK

9 5VSB 10 12V 11 12V 12 3.3V 13 3.3V 14 -12V 15 GND 16 GND 17 GND 18 GND 19 GND 20 RES/-5V 21 5V 22 5V 23 5V 24 GND

11

2

13 24

18

NSA 5160 User Manual

Chapter 2: Jumpers and Connectors

Block Diagram

Intel

BDX-DE

B1B0

DDR4 @ 2400MHz

A1A0

Channel A

Channel B

Cortina CS4227

KR

2x 10GbE SFP+

U

S

B

2

.

0

3x SATA3 Port

U

S

B

3

.0

1x USB3.0 Port

1x SATA DOM

Internal Connector

SATA3

PCIe Gen3 x1

SMBus

LPC (33MHz)

UART

SPI

AST 2300

VIDEO RGB

(Rear)

128MB DDR-3

16MB

EEPROM

10GbE

EEPROM

VR 12.5

PCIe Gen2 x1

P

C

I

e

G

e

n

3

x

8

CPLD

XDP

P

C

I

e

G

e

n

3

x

8

P

C

I

e

G

e

n

3

x

4

U

S

B

2

.

0

P

C

I

e

G

e

n

2

x

1

Intel I210

Intel I211

P

C

I

e

G

e

n

2

x

1

P

C

I

e

G

e

n

2

x

1

P

C

I

e

G

e

n

3

x

4

P

C

I

e

G

e

n

2

x

1

Intel I211

P

C

I

e

G

e

n

2

x

1

Intel I211

P

C

I

e

G

e

n

3

x

4

UART

SATA3

NC-SI

TPM

LPC (33MHz)

19

NSA 5160 User Manual

Chapter 3: System Setup

2. Gently slide the cover outwards, then lift up the cover to remove it.

ChaPter 3: system setuP

Removing the Chassis Cover

CAUTION!

CAUTION!CAUTION!

Prior to removing the chassis cover, make sure the unit’s power is off and disconnected from the power sources to prevent electric shock or system damage.

Lift here

1. Remove the screws on the chassis cover then put them in a safe place for later use.

20

NSA 5160 User Manual

Chapter 3: System Setup

Installing a SATA DOM

1. Locate the SATA DOM connector on the board.

2. Fasten a copper post on the mounting hole.

21

NSA 5160 User Manual

Chapter 3: System Setup

3. Install the SATA DOM to the connector with the mounting hole aligned to the copper post.

4. Fasten a screw on top of the copper post.

22

NSA 5160 User Manual

Chapter 3: System Setup

5. Connect the power cable to the power connector on the board.

23

NSA 5160 User Manual

Chapter 3: System Setup

Installing DIMM Memory Modules

1. Locate the DIMM sockets on the board.

2. Release the locks on the DIMM sockets.

3. Insert the module into the socket at an 90 degree angle. Apply firm even pressure to each end of the module until it slips into the socket.

4. While pushing the modules into position, the lock will close automatically.

24

NSA 5160 User Manual

Chapter 3: System Setup

Installing a 2.5” SATA Hard Drive

Please correctly follow the below instructions and noted items to avoid making unnecessary damages.

1. Remove the mounting screws that secure the hard drive bracket to the chassis.

2. Note the sides of the hard drive bracket. The longer side is designed to fit on the chassis’ standoff while the shorter side is designed to fit on the motherboard’s standoff.

Mounting screw

CAUTION!

CAUTION!CAUTION!

Longer side Shorter side

3.5” Bracket

Longer side Shorter side

2.5” Bracket

25

NSA 5160 User Manual

Chapter 3: System Setup

3. Place the SATA hard drive into the hard drive bracket with the SATA connector facing outwards.

SATA data and power connector

4. Align the mounting holes that are on the sides of the SATA drive with the mounting holes on the hard drive bracket. Then use the provided mounting screws to secure the SATA drive in place.

5. Repeat step 4 for securing the screws on the other side of the hard drive bracket.

3.5” Bracket

2.5” Bracket

26

NSA 5160 User Manual

Chapter 3: System Setup

6. Place the drive into the chassis with the connector side facing the board, and then use the provided mounting screws to secure the hard drive bracket in place.

7. Locate the SATA data connector on the board.

SATA data connector

Connector side

27

NSA 5160 User Manual

Chapter 3: System Setup

8. Plug the SATA data cable onto the connector, then plug the other end to

the SATA data connector on the hard drive.

SATA data cable SATA data connector

9. Plug the SATA power cable to the SATA power connector on the hard drive.

SATA power cable

28

NSA 5160 User Manual

Chapter 3: System Setup

Mounting screw Cover plate

Installing a LAN Module

The system is equipped with 2 LAN module bays. To install a LAN module, please follow the instructions below.

1. Remove the screw on the cover plate of the LAN module then put them in a safe place for later use. Each cover is secured by one screw.

Please correctly follow the below instructions and noted items to avoid making unnecessary damages. Make sure the power supply is switched off and disconnected from the power sources before replacing or adding LAN modules to prevent electric shock or system damage.

CAUTION!

CAUTION!CAUTION!

2. Use the handle provided, and insert the handle into the two holes on the LAN module cover.

Handle

Insert here

3. Once the handle is firmly secured in position, pull the handle outwards to remove the LAN module bay.

29

NSA 5160 User Manual

Chapter 3: System Setup

4. Place the LAN module into the tray making sure the connector side of the module is at the rear side of the tray.

Important:

Before using Optical fiber for transferring data, make sure you have connected an approved Optical Transceiver Module. User needs to install appropriate and UL approved Laser Class I Transceivers, rated 3.3Vdc, max. 1W.

5. Secure the module in place with screws, and slide the tray back into the

bay.

Connector

side

30

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

ChaPter 4: BIos setuP

This chapter describes how to use the BIOS setup program for the NSA 5160. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future.

To check for the latest updates and revisions, visit the NEXCOM website at www.nexcom.com.tw.

About BIOS Setup

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters.

These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS.

With easy-to-use pull down menus, you can configure such items as:

▪ Hard drives, diskette drives, and peripherals

▪ Video display type and display options

▪ Password protection from unauthorized use

▪ Power management features

The settings made in the setup program affect how the computer performs. It is important, therefore, first to try to understand all the setup options, and second, to make settings appropriate for the way you use the computer.

When to Configure the BIOS

▪ This program should be executed under the following conditions:

▪ When changing the system configuration

▪ When a configuration error is detected by the system and you are

prompted to make changes to the setup program

▪ When resetting the system clock

▪ When redefining the communication ports to prevent any conflicts

▪ When making changes to the Power Management configuration

▪ When changing the password or making other changes to the security

setup

Normally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS RAM has lost power, or the system features need to be changed.

31

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Default Configuration

Most of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.

Entering Setup

When the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines. These routines perform various diagnostic checks; if an error is encountered, the error will be reported in one of two different ways:

▪ If the error occurs before the display device is initialized, a series of beeps

will be transmitted.

▪ If the error occurs after the display device is initialized, the screen will

display the error message.

Powering on the computer and immediately pressing allows you to enter Setup.

Legends

Key Function

Moves the highlight left or right to select a menu.

Moves the highlight up or down between sub-menu or fields.

Exits the BIOS Setup Utility.

Scrolls forward through the values or options of the highlighted field.

Scrolls backward through the values or options of the highlighted field.

Selects a field.

Displays General Help.

Load previous values.

Load optimized default values.

Saves and resets the system.

Press <Enter> to enter the highlighted sub-menu

32

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Scroll Bar

When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields.

Submenu

When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press .

33

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

BIOS Setup Utility

Once you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from several setup functions and one exit. Use arrow keys to select among the items and press to accept or enter the submenu.

Main

The Main menu is the first screen that you will see when you enter the BIOS Setup Utility.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Set the Date. Use Tab to switch between Date elements.

BIOS Information

BIOS Vendor Core Version Compliancy Project Version Build Date and Time Access Level

Memory Information

Total Memory

System Date

System Time

American Megatrends

5.11 UEFI 2.4; PI 1.3 G516- 0.08 x64 03/02/2016 17:53:06 Administrator

4096 MB

[Thu 05/26/2016] [23:15:46]

System Date

The date format is <day>, <month>, <date>, <year>. Day displays a day, from Monday to Sunday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1999 to 2099.

System Time

The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59.

Access Level

Displays the access level of the current user in the BIOS.

34

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Advanced

The Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference.

Setting incorrect field values may cause the system to malfunction.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

System ACPI Parameters

Trusted Computing

AST2300 Super IO Conguration

Serial Port Console Redirection PCI Subsystem Settings

Network Stack Conguration CSM Conguration USB Conguration



Trusted Computing

This section is used to configure trusted computing settings.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.

Conguration

Security Device Support

TPM State Pending operation Device Select

Current Status Information

TPM Enabled Status TPM Active Status TPM Owner Status

[Enable]

[Enabled] [None] [Auto]

[Enabled] [Activated] [Owned]

Security Device Support

Enables or disables BIOS support for the security device. O.S. will not show security device. TCG EFI protocol and INT1A interface will not be available.

TPM State

Enables or disables the security device.

Pending Operation

Configures the operation mode for the security device.

Device Select

Configures the TPM version.

35

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

AST2300 Super IO Configuration

This section is used to configure the I/O functions supported by the onboard Super I/O chip.

Super IO Chip

Displays the Super I/O chip used on the board.

Serial Port 1 Configuration

Configuration settings for serial port 1.

Serial Port 2 Configuration

Configuration settings for serial port 2.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Set Parameters of Serial Port 1 (COMA)

AST2300 Super IO Conguration

Super IO Chip

Serial Port 1 Conguration

Serial Port 2 Conguration

AST2300



Serial Port 1 Configuration

This section is used to configure serial port 1.

Serial Port

Enables or disables the serial port.

Change Settings

Selects an optimal setting for the Super IO device.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 1 Conguration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3F8h; IRQ=4;

[Auto]

36

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Serial Port 2 Configuration

This section is used to configure serial port 2.

Serial Port

Enables or disables the serial port.

Change Settings

Selects an optimal setting for the Super IO device.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable or Disable Serial Port (COM)

Serial Port 2 Conguration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=2F8h; IRQ=3;

[Auto]

Serial Port Console Redirection

This section is used to configure the serial port that will be used for console redirection.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Console Redirection Enable or Disable

COM0

Console Redirection

Console Redirection Settings

COM1

Console Redirection

Console Redirection Settings

Legacy Console Redirection

Legacy Console Redirection Settings

Serial Port for Out-of-Band Management / Windows Emergency Management Services (EMS)

Console Redirection Console Redirection Settings

[Enabled]

[Disabled]

[Enabled]

Console Redirection (COM0/COM1/EMS)

Enables or disables console redirection for COM0/COM1/EMS.

►

37

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Console Redirection Settings (COM0)

Specifies how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more

COM0

Console Redirection Settings

Terminal Type

Bits per second Data Bits Parity Stop Bits Flow Control VT-UTF8 Combo Key Sup Recorder Mode Resolution 100x31 Legacy OS Redirection Putty KeyPad Redirection After BIOS

[ANSI]

[115200] [8] [None] [1] [None] [Enabled] [Disabled] [Disabled] [80x24] [VT100] [Always Enable]

Terminal Type

ANSI Extended ASCII character set. VT100 ASCII character set. VT100+ Extends VT100 to support color, function keys, etc. VT-UTF8 Uses UTF8 encoding to map Unicode characters onto 1 or more bytes.

Data Bits

The options are 7 and 8.

Bits Per Second

Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed.

Parity

A parity bit can be sent with the data bits to detect some transmission errors.

Even Parity bit is 0 if the number of 1’s in the data bits is even. Odd Parity bit is 0 if number of 1’s in the data bits is odd.

Stop Bits

Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit.

Flow Control

Flow control can prevent data loss from buffer overflow. When sending data and the receiving buffers are full, a “stop” signal can be sent to stop the data flow.

VT-UTF8 Combo Key Support

Enables or disables VT-UTF8 combination key support for ANSI/VT100 terminals.

Recorder Mode

When this field is enabled, only text will be sent. This is to capture the terminal data.

Resolution 100x31

Enables or disables extended terminal resolution.

Legacy OS Redirection

Selects the number of rows and columns that support redirection.

Putty Keypad

Selects the Putty keyboard emulation type.

Redirection After BIOS

The settings specify if BootLoader is selected, then Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy Console Redirection is enabled for Legacy OS.

38

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Console Redirection Settings (COM1)

Specifies how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more

COM0

Console Redirection Settings

Terminal Type

Bits per second Data Bits Parity Stop Bits Flow Control VT-UTF8 Combo Key Sup Recorder Mode Resolution 100x31 Legacy OS Redirection Putty KeyPad Redirection After BIOS

[ANSI]

[115200] [8] [None] [1] [None] [Enabled] [Disabled] [Disabled] [80x24] [VT100] [Always Enable]

Terminal Type

ANSI Extended ASCII character set. VT100 ASCII character set. VT100+ Extends VT100 to support color, function keys, etc. VT-UTF8 Uses UTF8 encoding to map Unicode characters onto 1 or more bytes.

Data Bits

The options are 7 and 8.

Bits Per Second

Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed.

Parity

A parity bit can be sent with the data bits to detect some transmission errors.

Even Parity bit is 0 if the number of 1’s in the data bits is even. Odd Parity bit is 0 if number of 1’s in the data bits is odd.

Stop Bits

Stop bits indicate the end of a serial data packet. (A start bit indicates the beginning). The standard setting is 1 stop bit. Communication with slow devices may require more than 1 stop bit.

Flow Control

Flow control can prevent data loss from buffer overflow. When sending data and the receiving buffers are full, a “stop” signal can be sent to stop the data flow.

VT-UTF8 Combo Key Support

Enables or disables VT-UTF8 combination key support for ANSI/VT100 terminals.

Recorder Mode

When this field is enabled, only text will be sent. This is to capture the terminal data.

Resolution 100x31

Enables or disables extended terminal resolution.

Legacy OS Redirection

Selects the number of rows and columns that support redirection.

Putty Keypad

Selects the Putty keyboard emulation type.

Redirection After BIOS

The settings specify if BootLoader is selected, then Legacy console redirection is disabled before booting to Legacy OS. Default value is Always Enable which means Legacy Console Redirection is enabled for Legacy OS.

39

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Legacy Console Redirection Settings

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Select a COM port to display redirection of Legacy OS and Legacy OPROM Messages

Legacy Serial Redirection Port

[COM0]

Legacy Serial Redirection Port

Configures the COM port to display redirection of legacy OS and legacy OPROM messages.

Console Redirection Settings (Serial Port for Out-of-Band Management)

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS through a serial port.

Out-of-Band Mgmt Port

Terminal Type Bits per second Flow Control

Data Bits Parity Stop Bits

[COM0]

[VT-UTF8] [115200] [None]

8 None 1

Out-of-Band Mgmt Port

Configures the out-of-band management port. Microsoft Windows Emergency Management Services (EMS) allows for remote management of a Windows Server OS via a serial port.

Terminal Type

ANSI Extended ASCII character set. VT100 ASCII character set. VT100+ Extends VT100 to support color, function keys, etc. VT-UTF8 Uses UTF8 encoding to map Unicode characters onto 1 or more bytes.

Bits Per Second

Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed.

Flow Control

Flow control can prevent data loss from buffer overflow. When sending data and the receiving buffers are full, a “stop” signal can be sent to stop the data flow.

40

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

PCI Subsystem Settings

This section is used to configure the PCI.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enables or Disables 64bit capable Devices to be Decoded in Above 4G Address Space (Only if System Supports 64bit PCI Decoding).

PCI Bus Driver Version

PCI Devices Common Settings:

Above 4G Decoding

SR-IOV Support

PCI Express Settings

A5.01.08

[Disabled]

Above 4G Decoding

Enables or disables decoding of 64bit devices in 4G address space.

SR-IOV Support

Enables or disables SR-IOV support.

►

PCI Express Settings

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enables or Disables PCI Express Device Relaxed Ordering.

PCI Express Device Register Settings

Relaxed Ordering

Extended Tag No Snoop Maximum Payload

[Disabled]

[Disabled] [Enabled] [Auto]

Relaxed Ordering

Enables or disables the PCI Express device relaxed ordering.

Extended Tag

When this function is enabled, it allows a device to use 8-bit tag field as a request.

No Snoop

Enables or disables the PCI Express device no snoop option.

Maximum Payload

Selects the maximum TLP payload size of the PCI Express device.

41

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Network Stack

This section is used to configure the network stack.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable UEFI Network Stack

Network stack

[Disabled]

Network Stack

Enables or disables UEFI network stack.

CSM Configuration

This section is used to configure the compatibility support module features.

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable CSM Support.

Compatibility Support Module Conguration

CSM Support

CSM16 Module Version

GateA20 Active Option ROM Messages INT19 Trap Response

Option ROM execution

Network Video Other PCI devices

[Enabled]

07.79

[Upon Request] [Force BIOS] [Immediate]

[Do not launch] [Legacy] [UEFI]

CSM Support

This field is used to enable or disable CSM support, if Auto option is selected, based on OS, CSM will be enabled or disabled automatically.

GateA20 Active

Upon Request GA20 can be disabled using BIOS services. Always Do not allow disabling GA20; this option is useful when any RT code is executed above 1MB.

42

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Option ROM Messages

This field is used to set display mode for Option ROM. The options are Force BIOS and Keep Current.

INT19 Trap Response

Allows Option ROMs to trap Interrupt 19 when enabled.

Network

Enables or disables the boot option for legacy network devices.

Video

Enables or disables the boot option for legacy video devices.

Other PCI Devices

Enables or disables the boot option for legacy PCI devices.

43

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Advanced

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

USB Conguration

USB Module Version

USB Controllers

1 EHCI, 1 XHCI

USB Devices:

4 Drives, 2 Keyboards, 2 Mice, 3 Hubs

Legacy USB Support

XHCI Hand-off EHCI Hand-off USB Mass Storage Driver Port 60/64 Emulation

USB hardware delays a

USB transfer time-out Device reset time-out Device power-up delay

13

[Enabled]

[Enabled] [Disabled] [Enabled] [Enabled]

[20 sec] [20 sec] [Auto]

Legacy USB Support

Enable Enables Legacy USB. Auto Disables support for Legacy when no USB devices are connected. Disable Keeps USB devices available only for EFI applications.

XHCI Hand-off

This is a workaround for OSs that does not support XHCI hand-off. The XHCI ownership change should be claimed by the XHCI driver.

USB Configuration

This section is used to configure the USB.

EHCI Hand-Off

This is a workaround for OSs that does not support EHCI hand-off. The EHCI ownership change should be claimed by the EHCI driver.

USB Mass Storage Driver

Enables or disables USB mass storage device driver support.

Port 60/64 Emulation

Enables I/O port 60h/64h emulation support. This should be enabled for complete USB keyboard legacy support for non-USB aware OS.

USB Transfer Time-out

The time-out value for control, bulk, and Interrupt transfers.

Device Reset Time-out

Selects the USB mass storage device’s start unit command timeout.

Device Power-up Delay

Maximum time the value will take before it properly reports itself to the Host Controller. “Auto” uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor.

44

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Displays and provides option to change the Processor Settings

Processor Conguration

Memory Conguration IIO Conguration PCH Conguration Network Conguration

------------------------------------------------------------------------------------Setup Warning: Setting items on this Screen to incorrect may cause system to malfunction!

Intel RC Setup

This section is used to configure the processor and chipset settings.

►

► ► ►

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Change Per-Socket Settings

Per-Socket Conguration

Processor Socket Socket 0 Processor ID 00050663* Processor Frequency 2.000GHz Processor Max Ratio 14H Processor Min Ratio 08H Microcode Revision 07000005 L1 Cache RAM 512KB L2 Cache RAM 2048KB L3 Cache RAM 12288KB Processor 0 Version Intel (R) Xeon (R) CPU D-

-1548 @ 2.00GHz

Hyper-Threading [ALL] [Enable] Execute Disable Bit [Enable] Enable Intel TXT Supp [Disabled] VMX [Enable] Enable SMX [Disable] Hardware Prefetcher [Enable]

Processor Configuration

Hyper-Threading [ALL]

Enables or disables hyper-threading technology.

Execute Disable Bit

When this field is set to Disabled, it will force the XD feature flag to always return to 0.

Enable Intel® TXT Support

Enables or disables Intel TXT support.

VMX

Enables or disables Virtual Machine Extensions.

IntelRCSetup

►

45

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Enable SMX

Enables or disables Secure Mode Extensions.

Hardware Prefetcher

Turns on or off the mid level cache (L2) streamer prefetcher.

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

CPU Socket 0 Conguration

Processor Configuration

CPU Socket 0 Configuration

Processor settings for the CPU on socket 0.

IntelRCSetup

►

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Number of Cores to Enable. 0 means all cores. 8 Cores available.

CPU Socket 0 Conguration

------------------------------------------------------------------------------------

Cores Enabled

IOT Cfg Cbo Bitmap 0

CPU Socket 0 Configuration

Cores Enabled

Configures the number of cores to enable. 0 means all cores.

IoT Cfg Cbo Bitmap

Configures the bit to enable IOT/OCLA.

IntelRCSetup

0

46

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Maximum Memory Frequency Selections in Mhz. Do not select Reserved

-----------------------------------------------------------------------------------Integrated Memory Controller (iMC)

------------------------------------------------------------------------------------

Memory Frequency

Memory Topology

Memory Configuration

Memory Frequency

Configures the maximum frequency of the memory. Do not select Reserved.

IntelRCSetup

[Auto]

►

Memory Topology

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

-----------------------------------------------------------------------------------Socket0.Ch0.Dimm0: 2133MT/s UNKNOWN SRx8 4GB RDIMM

IntelRCSetup

Detects and displays the information on the memory installed.

47

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Set this option to allow DFX Lock Bits to remain clear

IIO Conguration

------------------------------------------------------------------------------------

EV DFX Features [Disable]

IIO0 Conguration IOAT Conguration IIO General Conguration

Intel VT for Directed I/O (VT-d)

IIO Configuration

IntelRCSetup

► ►

►

EV DFX Features

Enables or disables DFX lock bits to remain clear.

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Selects PCIe port Bifurcation for selected slot(s)

IOU2 (IIO PCIe Port 1

IOU0 (IIO PCIe Port 2 IOU1 (IIO PCIe Port 3 No PCIe port active E Socket 0 PcieD00F0 - Port 0/DMI Socket 0 PcieD01F0 - Port 1A Socket 0 PcieD01F1 - Port 1B Socket 0 PcieD02F0 - Port 2A Socket 0 PcieD02F2 - Port 2C Socket 0 PcieD03F0 - Port 3A Socket 0 PcieD03F2 - Port 3C

IIO Auto Programming

IIO0 Configuration

IntelRCSetup

[x4x4]

[Auto] [x8x8] [PCU Squelch exit ig. . .]

[Enable]

►

IOU2, IOU0 and IOU1 (IIO PCIe Port 1 to Port 3)

Port Bifurcation settings for IOU2, IOU0 and IOU1.

No PCIe Port Active

Configures the workaround solution for ECO when the PCIe ports are not active.

IIO Auto Programming

Enables or disables auto programming of IIO.

48

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Socket 0 PCIED00F0 - Port 0/DMI Socket 0 PCIED00F0 - Port 1A to Socket 0 PCIED03F2 - Port 3C

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Socket 0 PcieD00F0 - Port 0/DMI

------------------------------------------------------------------------------------

Link Speed

PCI-E Port DeEmphasis

PCI-E Port Link Status PCI-E Port Link Max PCI-E Port Link Speed

IntelRCSetup

[Auto]

[-6.0 dB]

Linked as x4 Max Width x4 Gen 2 (5.0 GT/s)

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Socket 0 PcieD0xFx - Port xx

------------------------------------------------------------------------------------

PCI-E Port

PCI-E Port Link Link Speed PCI-E Port DeEmphasis

PCI-E Port Link Status PCI-E Port Link Max PCI-E Port Link Speed

IntelRCSetup

[Auto]

[Enable] [Auto] [-6.0 dB]

Linked as x4 Max Width x4 Gen 2 (5.0 GT/s)

Link Speed

Configures the link speed of the PCIe port.

PCI-E Port DeEmphasis

Configures the level of the PCIe port de-emphasis.

PCI-E Port

Enables or disables the PCIe port.

PCI-E Port Link

Enables or disables link training of the PCIe port.

Link Speed

Configures the link speed of the PCIe port.

PCI-E Port DeEmphasis

Configures the level of the PCIe port de-emphasis.

49

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit Save & Exit

Advanced AdvancedSecurity SecurityBoot BootMain Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Control to enable/disable IOAT devices

Allows selection of the TXT DPR size in system

Enable IOAT

No Snoop Disable TPH

TXT DPR memory setting

----------------------------------------------------------------------------------... IIO 0

----------------------------------------------------------------------------------...

IIO IOAPIC

----------------------------------------------------------------------------------...

IOAT Configuration IIO General Configuration

IntelRCSetup IntelRCSetup

[Disable]

[Disable] [Enable]

[3M DPR]

[Enable]

Enable IOAT

Enables or disables Intel® I/O Acceleration Technology.

No Snoop

Enables or disables PCIe no snoop attribute for the processor caches.

Disable TPH

Enables or disables transactions processing hints (TPH).

TXT DPR Memory Setting

Configures the TXT DPR size.

IIO IOAPIC

Enables or disables I/O Advanced Power Interface Configuration (IOAPIC) for IIO 0.

50

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable Intel Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI Tables.

Intel VT for Directed I/O (VT-d)

------------------------------------------------------------------------------------

Intel VT for Directed I/O

Intel VT for Directed I/O (VT-d)

IntelRCSetup

[Enable]

Intel VT for Directed I/O

Enables or disables Intel® Virtualization Technology for Directed I/O (VT-d) by reporting the I/O device assignment to VMM through DMAR ACPI tables.

51

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable Intel(R) IO Controller Hub devices

PCH Conguration

------------------------------------------------------------------------------------

PCH Devices

PCI Express Conguration PCH SATA Conguration USB Conguration

PCH Configuration

IntelRCSetup

►

► ► ►

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable SMBUS Device.

SMBUS Device

PCH Display PCH state after G3

PCH Devices

IntelRCSetup

[Enabled]

[Enabled] [S0]

SMBUS Device

Enables or disables SMBUS device.

PCH Display

Enables or disables the PCH Display.

PCH State After G3

Configures the PCH state after G3.

52

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit Save & Exit

Advanced AdvancedSecurity SecurityBoot BootMain Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable PCIe root port function swapping feature to dynamically assign function 0 to enabled root port.

Control the PCI Express Root Port.

PCIe Root Port Function

PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 PCI Express Root Port 4 PCI Express Root Port 5 PCI Express Root Port 6 PCI Express Root Port 7 PCI Express Root Port 8

PCI Express Root Port

PCIe Speed

PCI Express Configuration PCI Express Root Port 1 to Port 8

IntelRCSetup IntelRCSetup

[Enabled]

[Auto]

PCIe Root Port Function

Enables or disables PCIe root port function swapping feature to dynamically assign function 0 to the enabled root port.

PCI Express Root Port

Enables or disables the PCIe root port.

PCIe Speed

Configures the PCIe speed for the root port.

► ► ► ► ► ► ► ►

53

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable or Disable SATA Controller

SATA Controller

Congure SATA as

SATA Port 0

Port 0 Hot Plug SATA Device Type

SATA Port 1

Port 1 Hot Plug SATA Device Type

SATA Port 2

Port 2 Hot Plug SATA Device Type

SATA Port 3

Port 3 Hot Plug SATA Device Type

PCH SATA Configuration

IntelRCSetup

[Enabled]

[AHCI]

[Not Installed]

[Enabled] [Disabled] [Hard Disk Drive]

[Not Installed]

[Enabled] [Disabled] [Hard Disk Drive]

[Not Installed]

[Enabled] [Disabled] [Hard Disk Drive]

[Not Installed]

[Enabled] [Disabled] [Hard Disk Drive]

SATA Controller

Enables or disables the SATA controller.

Configure SATA as

Configures the SATA as IDE or AHCI. IDE This option configures the Serial ATA drives as Parallel ATA physical storage device.

AHCI This option configures the Serial ATA drives to use AHCI (Advanced Host Controller Interface). AHCI allows the storage driver to enable the advanced Serial ATA features which will increase storage performance.

Port 0 to Port 3

Enables or disables Serial ATA port 0 to port 3.

Hot Plug

Enables or disables hot plugging feature on Serial ATA port 0 to port 3.

SATA Device Type

Identifies what type of SATA device is connected on port 0 to port 3.

54

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Mode of operation of xHCI controller.

xHCI Mode

Trunk Clock Gating

USB Configuration

IntelRCSetup

[Auto]

[Enabled]

xHCI Mode

Configures the XHCI mode.

Trunk Clock Gating

Enables or disables Trunk Clock Gating.

Save & Exit

Advanced Security BootMain

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Switch ByPass Auto Detect to Enable/Disable

Network Conguration

------------------------------------------------------------------------------------

ByPass Auto Detect

If all the PCIE slots don't insert the Lan Module or all the Lan Modules don't support ByPass function, the options of the ByPass will not be shown!!

Network Configuration

IntelRCSetup

[Enabled]

ByPass Auto Detect

Enables or disables automatic LAN Bypass function.

55

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Server Mgmt

BMC Support

Enables or disables interfaces to communicate with BMC.

Wait for BMC

Enables or disables waiting for BMC.

BMC Warm Reset

To perform a BMC warm reset, select this field then press <Enter>.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enable/Disable interfaces to communicate with BMC

BMC Self Test Status BMC Device ID BMC Device Revision BMC Firmware Revision IPMI Version

BMC Support

Wait For BMC System Event Log

BMC network conguration

View System Event Log BMC User Settings BMC Warm Reset

PASSED 32 1

0.72

2.0

[Enabled]



Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Change this to enable or disable all features of System Event Logging during boot.

Enabling/Disabling Options

SEL Components

Erasing Settings

Erase SEL When SEL is Full

Custom EFI Logging Options

Log EFI Status Codes

NOTE: All values changed here do not take until computer is restarted.

[Enabled]

[No] [Do Nothing]

[Error code]

System Event Log

SEL Components

Enables or disables all the features of system event logging during boot.

Erase SEL

Configures the options for erasing SEL.

When SEL is Full

Configures the action to perform when SEL is full.

Log EFI Status Codes

Configures the options for logging EFI status codes.

56

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Select to congure LAN

channel parameters statically or dynamically(by BIOS or

BMC). Unspecied option will

not modify any BMC network parameters during BIOS phase

--BMC network conguration--

*********************

Congure IPV4 support

*********************

Lan channel 1

Conguration Address

Current Conguration

Station IP address Subnet mask Station MAC address

*********************

Congure IPV6 support

*********************

Lan channel 1

IPV6 is not supported in BMC.

[Unspecied]

DynamicAddressBmcDhcp

0.0.0.0

0.0.0.0 00-00-00-00-00-00

BMC Network Configuration

Configuration Address

Select to configure LAN channel parameters statically or dynamically (by BIOS or BMC). Unspecified option will not modify any BMC network parameters during BIOS phase.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

No. of log entries in SEL : 0

<< System Event Log is Empty >>

View System Event Log

Displays system event log information including date, time and sensor type.

57

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit Save & ExitAdvanced AdvancedIntelRCSetup IntelRCSetupServer Mgmt Server Mgmt

Security SecurityBoot Boot

Main Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Press <Enter> to Add a User. Enter BMC User Name

BMC User Settings

Add User

Delete User

Change User Settings

BMC Add User Details

User Name

User Password Channel No User Privilege Limit

0 [Reserved]

BMC User Settings BMC User Settings - Add User

Add User

Option to add a user.

Delete User

Option to delete a user.

Change User Settings

Option to change user settings.

User Name

Configures a username for the new user account.

User Password

Configures a password for the new user account.

Channel No

Assigns a channel number for the new user account.

User Privilege Limit

Configures the access privileges of the new user account.



58

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit Save & ExitAdvanced AdvancedIntelRCSetup IntelRCSetupServer Mgmt Server Mgmt

Security SecurityBoot Boot

Main Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Enter BMC User Name Enter BMC User Name

BMC Delete User Details

User Name

User Password

BMC Change User Settings

User Name

User Password User Change User Password Channel No User Privilege Limit

[Disable]

0 [Reserved]

BMC User Settings - Delete User BMC User Settings - Change User Settings

Deletes the specified user account. Reconfigures user account settings such as username, password, channel

number and access privileges.

59

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Security

Administrator Password

Select this to reconfigure the administrator’s password.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Set Administrator Password

Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User Will have Administrator rights. The password length must be in the following range:

Minimum length 3 Maximum length 20

Administrator Password

60

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Boot

Setup Prompt Timeout

Selects the number of seconds to wait for the setup activation key. 65535(0xFFFF) denotes indefinite waiting.

Bootup NumLock State

This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.

Quiet Boot

Enabled Displays OEM logo instead of the POST messages. Disabled Displays normal POST messages.

AMI Virtual Device

Enables or disables AMI virtual device.

Boot Mode Select

Configures the boot mode option.

Fixed Boot Order Priorities

Adjust the boot sequence of the system. Boot Option #1 is the first boot device that the system will boot from, next will be Boot Option #2 and so forth.

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security

Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Number of seconds to wait for setup activation key.

65535(0xFFFF) means indenite

waiting.

Boot Conguration

Setup Prompt Timeout

Bootup NumLock State Quiet Boot

AMI Virtual Device

Boot mode select

FIXED BOOT ORDER Priorities

Boot Option #1 Boot Option #2 Boot Option #3 Boot Option #4 Boot Option #5 Boot Option #6 Boot Option #7 Boot Option #8

[On] [Disabled]

[Disable]

[LEGACY]

[USB CD/DVD] [USB Key] [Hard Disk] [USB Hard Disk] [CD/DVD] [USB Floppy] [USB Lan] [Network]

1

61

NSA 5160 BIOS Manual

Chapter 4: BIOS Setup

Save & Exit

Save & ExitAdvanced IntelRCSetup Server Mgmt

Security Boot

Main

→←: Select Screen ↑↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit

Reset the system after saving the changes.

Save Options

Save Changes and Exit

Discard Changes and Exit

Save Changes and Reset Discard Changes and Reset

Default Options

Restore Defaults

Boot Override

Save Changes and Exit

To save the changes and exit the Setup utility, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes. You can also press <F4> to save and exit Setup.

Discard Changes and Exit

To exit the Setup utility without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting. You can also press <ESC> to exit without saving the changes.

Save Changes and Reset

To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Discard Changes and Reset

To exit the Setup utility without saving the changes, select this field then press <Enter>. You may be prompted to confirm again before exiting.

Restore Defaults

To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes.

Boot Override

To bypass the boot sequence from the Boot Option List and boot from a particular device, select the desired device and press <Enter>.