USER MANUAL
▍MODEL:
* LCMR-300 (300W Incandescent lam p)
* LCMR-1000 (1000W Resistive load)
▍FEATURES:
* Learning function, easy operation.
* Receiver has 6 memory settings, no memory loss forever.
* Red LED indicator for POWER ON and MEMORY SETTINGS.
* Learning function Receiver compatible to all ARC transmitters (including learning transmitter
and code switch transmitter).
* Remote control till 30M in open area.
▍INSTALLATION:
Controller (Receiver)
* Disconnect main power before installation.
* Screw holder of receiver can be cut off if necessary.
* Connect AC wire and load (lamp) to receiver
block terminal (fig. 1).
* Connect main power on.
* LED indicator on receiver should light on.
Remote control (Transmitter)
Learning system transmitter (fig. 2)
* Learning system has million codes which is house
code.
* The million codes are set up in each transmitter
before shipping out of factory.
* Million code of each transmitter will have very few
chance to be the same with other transmitters.
* LYCT-505 can remote control max. 16 receivers.
LED indicator on the transmitter will light on
while pressing the button.
* LWST-605 can control 2 receivers.
Code switch transmitter (fig. 3)
* YCT-100 & YCT-603 max. control 16 receivers (under a house code)
LED indicator on the transmitter will light on while pressing the button.
* WST-512 can control 1 recei ver only .
Page 1
Link transmitter with receiver (fig. 4)
* LCMR can be remote controlled by wall switch
or handy transmitter.
* Cover LWST-605 or WST-512 to LCMR
as a wall switch to remote control LCMR.
* Or use LYCT-505 / YCT-603 / YCT-100 to handy
remote control LCMR.
* All ARC transmitters with other functions such like
sensor function can also remote control LCMR.
▍HOW TO SET CODE: learning function:
* To start, program your transmitter with the
receiver.
* Connect power to receiver (fig.1).
* Bring the transmitter near the receiver, push the
learning button on receiver once (fig.4)
* Receiver LED will blink slowly, press transmitter
selected “ON” button.
* Receiver connected lamp will blink twice, code is
confirmed and LED stops blinking.
* Remember the transmitter button you selected for the
programmed receiver.
▍HOW TO CHANGE OR DELETE
CODE :
DELETING INDIVIDUALLY- ALL MEMORY DELETE -
*Push the learning button once, LED will blink slowly. * Push the learning button for 6 sec.., LED will blink continuously.
* Press selected “OFF” button on transmitter, * Release and push again once.
which selected programmed memory is deleted. * Receiver connected lamp will blink twice for confirmation.
* Receiver connected lamp will blink twice for confirmation. * ALL PROGRAMMED MEMORY WILL BE DELETED
* Repeat step for re-setting. FROM RECEIVER.
▍RECEIVER HAS 6 MEMORY SETTINGS:
* Learning function RECEIVER has 6 memory settings.
* It can be programmed as to your requirement with special effect. It can be programmed to switch ON at one time individually
or programmed with different combinations switching.
* This means one receiver can be programmed into max. 6 different combinations.
Example : if there are 3 receivers, [ receiver 1 = lamp shade , receiver 2 = night light , receiver 3 = ceiling light ]
Receiver 1,2,3 can be control individually with transmitter button 1,2,3
Receiver 1,3 can be programmed with transmitter button 4, ( lamp shade and ceiling light ON/OFF at same time )
Receiver 1,2,3 can also be programmed into group function ALL ON or OFF at same time into group button
( lamp shade, night light and ceiling light ON/OFF at same time )
(Above settings ‘Receiver 1’ and ‘3’ takes up 3 programmed memory and ‘Receiver 2’ only 2 program memory,
different combinations and settings can be teamed up and controlled from transmitter )
▍OPERATION:
TRANSMITTER DIMMER RECEIVER(LCMR-300)
ON button – control receiver ON/DIMMER * Press transmitter button ‘ON’ twice, light will start to dim,
OFF button – switch OFF function press again, light stops at required brightness.
GROUP button – ALL ON or ALL OFF at the same time * To dim again, restart as above procedures.
Page 2
Direct 16 controls button
– (LYCT-505 / YCT-603 / YCT-100)
Channel I - 1,2,3,4 ON/OFF RECEIVER(LCMR-1000)
Channel II – 5,6,7,8 * Press transmitter button ‘ON’ to switch on.
Channel III – 9,10,11,12 * Press transmitter button ‘OFF’ to switch off.
Channel IV – 13,14,15,16
▍SPECIFICATION:
IP : 20
Class: I
T(max): 40℃
Frequency: 433.92MHz
Power: 230V ～ +/-10%, 50Hz
LCMR-300 : 300 W / 230V～ (incandescent lamp)
LCMR-1000: 1000W / 230V～(Resistive load)
▍FAULT FINDING:
No activation : Check battery direction or running out battery of
transmitter.
Replace new fuse (fig. 5):
* disconnect main power, put fuse into fuse hole (step1).
* put fuse hole into the main module (step2) and connect main power on.
Fuse specification:
LCMR-300: T1.6A H250V
LCMR-1000 T5A H250V
▍CAUTION :
Do not place two receivers near each other, the distance should be above 1 meter.
▍Warning!
DO NOT OVERLOAD
Do not use in damp places like patios, cellar, flammable liquid, solvents, paints etc…
▍Manufacturing site:
HOMEWELL Electronics Co., Ltd.
Address: NO.7~8 Building, the 5th. Industrial Park, Xia Village Gong Ming Town, Baoan District, Shenzhen city , China
Page 3
Loading...