New Space Design BVR-01 User Manual

BVR-01 GPS Video Recorder

User Manual

New Space Design Co., Ltd.

Thewarrantycardandinformationareprintedwithusermanual

Warranty

BVR

GPS Video Recorder

ADSBV001-0

Video Recorder + GPS

Camera

01

Index

Description & Feature

Specification

Product Overview

Getting Started

User Interface

Question/Troubleshooting

Package List

Safety Precautions

................................................... 02

.................................................................... 03

........................................................... 04

............................................................... 06

................................................................. 17

.......................................... 26

.................................................................... 27

........................................................ 28

02

Description & Feature

01

BVR has the function of video recording with GPS information for outdoors. People

always like to memorize the happening from the picture or video. However, it doesn’t

provide the information of location. And, people are sometimes hard to recall it. From

BVR’s application, user can easily recall the image and location because we combine

all information together.

► VGA(640x480) with 300,000 pixels

► MPEG-4 A/V encode @ VGA 30 FPS

► MicroSD for storing video files

► Customize User Interface

► Camera view angle: 63 degree

► 2 batteries of AAA size

► Car charger for vehicle used

► Support time zone setting

► Support language: English, Traditional Chinese, and Simple Chinese

► Function of changing recording length

03

Specification

02

Array Element

Sensor Size

Image Transfer Rate(Max)

Scan Mode

Electronic Exposure

Pixel Size

Image Area

640x480 (VGA)

1/4”
VGA, CIF, QCIF, QQCIF －30 fps．
QVGA, QQVGA －60 fps

Progressive

Up to 510:1 (for selected fps)

6 μm x 6 μm

3.984 mm×2.952 mm

CMOS Sensor

Power Source

Power Consumption

Operating Temperature

Operating Humidity

1. AAA x 2 Battery ( Ni-H ),

2. Car Adapter (3V/1A)

350mA 2.4V

Under 65˚C

5% ~ 85%

Power

Environment

Appearance

GPS

GPS Chipset

Frequency

Channels

Antenna

Datum

Cold Start

Warm Start

Hot Start

Reacquisition

Sensitivity

Dimension

Weight

Storage

SiRF Star III

L1, 1575.42MHz

12 CH for tracking

GPS Patch Antenna

WGS-84

50 sec , average

33 sec , average

1 sec , average

< 1 sec

-158dbm

98 x 34 28mm

47.5g

MicroSD

*Above data is based on open sky condition

04

Product Overview

03

- Top View - - Bottom View -

Low Battery Indicator

Screw hole for holder

Battery Cover

DC Jack

Record Indicator

GPS Indicator

Microphone

05

Product Overview

- Front View - - Back View -

- Left View -

Camera

Power / Function Button

MicroSD Card SocketBuzzer

06

Getting Started

04

1. Insert MicroSD card 2. Open the battery cover and insert
two AAA batteries.

1. Battery Mold for bike

Note: 1. Please use MicroSD card of class 6 or Higher

2. Please use application to formation your
MicroSD before insert into the device

07

3. Attach the holder on the bottom of device.

Getting Started

08

Getting Started

4. Firm the holder with device by hand screw.

09

Getting Started

5. Assembly the mounting frame with device.

10

Getting Started

6. Place the device on the bike.

11

2. DC Mold for vehicle

Getting Started

2. Combine the holder with mounting frame
and attach it on the windshield.

1. Insert MicroSD card

Note: 1. Please use MicroSD card of class 6 or Higher

2. Please use application to formation your
MicroSD before insert into the device

12

Getting Started

3. Start the vehicle engine.

4. Plug in the DC jack of car adapter and connect the power cable with the car cigarette lighter.

13

Getting Started

5. Assembly the holder with device and adjust the device to make sure
that the camrea can get the best view.

14

3. Start the record function

Getting Started

1. Press the power switch (1 second). Then, release the power switch. The buzzer will have
a short beep.

15

Getting Started

2. GPS indicator lights up. It means that the device is searching GPS signal. when GPS fixed,
GPS indicator will start blinking by the interval of 3 seconds.

3. When record indicator starts blinking by the interval of 3 seconds, it means the device is
recording.

16

Getting Started

5. Press the power switch (3 seconds) when the system is power on. Then, release the power
switch. Record indicator will light up and buzzer will have a short beep. After that, Record
indicator will turn off. The buzzer will have a long beep during the same time. It means that
system is turned off.

4. Trun off the power

1. Insert the CD-ROM to your computer.

2. The system will automatically pop out the setup window. Or, you can double
click “Setup.exe” in CD-ROM drive

17

User Interface

05

1. Install application

18

User Interface

3. Click “Next” for the following setup.

4. After installing the application, there is an icon shows on the desktop.

19

User Interface

5. Connect MicroSD, unplugged from BVR, with PC.

6. Double click the icon to run the application.

20

User Interface

7. Select your language

8. Click the first button to find the video file from MicroSD and open it.

9. The video file will show on this table.

21

User Interface

9. When the video is playing, the application shows the relative location on the map as well.
The icon on the up-right corner is the function to enlarge the map.

8. Click the button to play the video.

22

User Interface

10. When the video is playing, the application shows GPS Information with Speed,
Distance, Time, Longitude, Latitude, Altitude, and Compass as well.

11. User can click the video bar to jump video frames.

12. Click the speaker icon to mute or un-mute the volume.

23

User Interface

2. System Setup

2. Click the tool button to open the window of System Setup.

3. After “System Setup” as page 24, disconnect MicroSD from PC. And then, plug it in the
device. The system of device would automatically update the setting.

1. Connect MicroSD unplugged from device with PC

24

User Interface

Time zone

SBAS

File overwrite

Speed OSD

Disable warning

Record Time

Format

Setup dierent time zone for dierent
nation location.

If the user locates in Japan or U.S.A,
please select the item for the accuracy
of GPS.

If the memory of MicroSD is full, the
system will overwrite the oldest le.

Show the speed on the video screen.

Turn o the alarm of memory full and
low battery condition.

Select the recording time of the video
le (10, 20, 30, 60 minutes)

User must use this function to format
microSD card before using BVR

25

User Interface

Memory Condition

When the memory card is almost full (175Mb remained): Record indicator will stay in steady
ON state with three beep sounds. And, the alarm would repeat by 2 minutes until the memory
remain 1Mb or less.

Low Battery Condition

When the voltage of battery is less than 2.2V, Low Battery Indicator (Green light) will start blinking
by the interval of 0.5 second with three beep sounds. The Alarm would repeat by 2 minutes.
The system would turn off until the voltage is lower than 2.0V. The repeated alarm would continue
2~5 times depended on the different brands of the battery.

26

This chapter presents some troubleshooting problems you may encounter while using
the device. Even if the following guide fails to solve your problem, please do not
disassemble the device, but leave the problems to professional staff.

Question/Troubleshooting

06

TroubleshootingTrouble

Power light not turn on

The date or time of video is
not correct.

No Map information

No video file

No GPS signal

1. Remove the battery and replace the new sets.

2. Remove the car adapter and plug it again.

Go to System setup to select the time zone of your
nation before recording.

Make sure your PC has internet connection
before play the video file.

Please format MicroSD before plug in the device
for recording.

1. To get GPS signal, you need to power on the
device at the place of open sky.

2. When traveling to other country, GPS fixed may
be over 3 minutes.

27

Package List

07

BVR x 1

Mounting Frame (for Vehicle) x1

Holder 02 x 1

Power Cable x 1

Jelly Case x 1

Mounting Frame (for Bike) x1

CD-ROM x 1

Holder 01 x 1

User Manual x 1

28

Safety Precautions

08

1. Please turn off the power when inserting or removing MicroSD card.
Otherwise, it may cause damage to MicroSD card, or the unit.

2. Your product is a sophisticated electronic device. Do not drop or subject the unit to
jarring or strong vibrations.

3. Avoid placing the product in areas of high humidity or where it might be subjected to
splashing.

4. The panel is made of plastic and can be easily damaged. Avoid sharp objects.

5. Use only the supplied adaptor with Output 3V/1A.

6. Turn off power before cleaning. Use only a soft cloth to clean the unit. Do not use
liquid cleaners.

7. Avoid exposing the unit to extreme heat.

8. Do not disassemble the product, otherwise it may result in electric shock and void
your warranty.

Warranty

Thank you for purchasing BVR 01. Our product of GPS video tracker has been passed the critical
examination from certicated lab. If the product is in malfunction or damaged due to quality problem,
please send it for repair. Free maintenance service is oered with 12 months from the date of
purchasing. Warranty is to be proved with the Warranty Card included in the Packing Case. When
purchasing the product, please check and ensure a Warranty Card is in the case and ask the dealer to
x shop stamp and insert date and model number on it to validate. When the product purchased is
exceeded Free Warranty Period, we will charge fee for the maintenance and service.

This warranty does not cover malfunction or damage resulted from the list below

1. Natural disaster, ood, earthquake, some unstoppable disasters, and improper use.

2. Product dismantle and modify unauthorized.

3. Use expendable that is not designated from our company.

4. Malfunction and damage by shipping process after purchasing the product.

5. Malfunction and damage after exceeded free warranty period.

6. Revise the content of warranty card without company authorization.
in such cases, material cost and service fee will be charged.

Instruction

29

Warranty

Q&A Service

Q1: How to know the free warranty period if owner cannot provide the warranty card or relative document?
A1: We oer two conditions below for recognition of warranty period to insure customer’s rights:
a. Keep the receipt of buying this product for proof.
b. Add 3 months from the shipping month as the beginning month of warranty period.
(E.g. if the shipping month is in January 2010, the warranty period is to April 2011.

Q2: What kind of condition that service charge is needed?
A2: The list below is the condition of service charge:

1. Warranty is expired.

2. Cannot provide the warranty card or relative document.

3. Cannot recognize the serial number and bar code on the device due to the sticker of serial number and
barcode has been damaged.

4. Natural disaster or improper use.

5. Use unauthorized power, drop the device, place in the water, insert the object that is not the device’s parts,
dismantle or modify the device without the authorization, or use unauthorized parts or expendable.

30

Warranty

Repair Service

Please contact with us if your device has the problem. Pleasae mail the device with the address below
if you need the repair service.

Please ll out the information of warranty

Model Number

Purchasing Date

Serial Number

Purchasing Place

New Space Design CO.,Ltd.

xxxxxxxxxxxxxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxx

xxxxxxxxxxxxxxxxx

[email protected]

(Note: The shipping fee will be charged by sender. Our company only covers the shipping fee of the return.)

Address:

Tel:

Fax:

E-mail:

31

New Space Design Co., Ltd.