Newport MFA, MFA-CCV6, MFA-CC, MFA-PP, MFA-PPD User Manual

Miniature

Linear Stages

MFA Series

USER’S MANUAL

G

U

A

R

A

N

T

E

E

D

S

P

E

C

I

F

I

C

A

T

I

O

N

S

EDH0199En2041 — 12/18 ii

MFA Series Miniature Linear Stages

Warranty

Newport Corporation warrants this product to be free from defects in
material and workmanship for a period of 1 year from the date of
shipment. If found to be defective during the warranty period, the product
will either be repaired or replaced at Newport’s discretion.

To exercise this warranty, write or call your local Newport representative,
or contact Newport headquarters in Irvine, California. You will be given
prompt assistance and return instructions. Send the instrument,
transportation prepaid, to the indicated service facility. Repairs will be
made and the instrument returned, transportation prepaid. Repaired
products are warranted for the balance of the original warranty period, or
at least 90 days.

Limitation of Warranty

This warranty does not apply to defects resulting from modification or
misuse of any product or part.

This warranty is in lieu of all other warranties, expressed or implied,
including any implied warranty of merchantability or fitness for a
particular use. Newport Corporation shall not be liable for any indirect,
special, or consequential damages.

by Newport Corporation, Irvine, CA. All rights reserved.

Original instructions.

No part of this document may be reproduced or copied without the prior
written approval of Newport Corporation. This document is provided for
informa ti on only, and pro du ct specifications are subject to change without
notice. Any change will be reflected in future publishings.

CAUTION

Warranty does not apply to damages resulting from:

• Incorrect usage:

– Load on the stage greater than maximum specified load.

– Carriage speed higher than specified speed.

–Improper grounding.

¬ Connectors must be properly secured.

¬ When the load on the stage represents an electrical risk, it must

be connected to ground.

– Excessive or improper cantilever loads.

• Modification of the stage or any part thereof.

CAUTION

Please return equipment in
the original (or equivalent)
packing.

You will be responsible for
damage incurred from
inadequate packaging if the
original packaging is not
used.

© 2018

iii EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

Table of Contents

Warranty .................................................................................................................ii

EC Declaration of Conformity...............................................................................v

Definitions and Symbols.......................................................................................vi

Warnings ...............................................................................................................vii

Caution .................................................................................................................viii

1.0 — Introduction.................................................................................1

2.0 — Description ...................................................................................2

2.1 Design Details ............................................................................................2

3.0 — Characteristics............................................................................3

3.1 Definitions ..................................................................................................3

3.2 Mechanical Specifications .......................................................................4

3.3 Load Specification Definitions.................................................................4

3.4 Load Characteristics and Stiffness .........................................................5

3.5 Stage Weights ............................................................................................5

4.0 — Drives and Motors ....................................................................6

4.1 Stepper Drive Version ..............................................................................6

4.2 DC-Motor Drive Version ...........................................................................6

4.3 Sensor Position..........................................................................................7

4.4 Feedback Signal Position .........................................................................8

4.5 Pinouts........................................................................................................8

5.0 — Connection to Newport Controllers ..............................10

5.1 Warnings on Controllers ........................................................................10

5.2 Connection ...............................................................................................11

5.3 Cables .......................................................................................................11

6.0 — Connection to Non-Newport Electronics ....................12

6.1 MFA-PPD & MFA-CC Connections .........................................................12

6.2 MFA-PP Stage ...........................................................................................13

7.0 — Dimensions.................................................................................13

8.0 — Accessories.................................................................................14

8.1 MFA-BK Plate ...........................................................................................14

8.2 (M-)MFA-TP Top Plates ..........................................................................14

8.3 MFA-BP Base Plate ..................................................................................14

EDH0199En2041 — 12/18 iv

MFA Series Miniature Linear Stages

9.0 — Maintenance ..............................................................................15

9.1 Maintenance ............................................................................................15

9.2 Repair .......................................................................................................15

9.3 Calibration ...............................................................................................15

Service Form .........................................................................................................17

v EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

MFA Series

EU Declaration of Conformity

following Annex II-1A
of Directive 2006/42/EC on machinery

The manufacturer:

MICRO-CONTROLE Spectra-Physics,
9, rue du bois sauvage
F-91055 Evry FRANCE

Hereby declares that the machinery:

y Description: " MFA "
y Function: Miniature Linear Stages
y Models: MFA-CC/-CCV6/-PP/-PPD

– the technical file of which was compiled by:

Mr Hervé LE COINTE, Quality Director,
MICRO-CONTROLE Spectra-Physics, Zone Industrielle - B.P.29
F-45340 Beaune La Rolande France

– complies with all the relevant provisions of the Directive 2006/42/EC on machinery.
– complies with all the relevant provisions of the Directive 2014/30/EU relating to electro­magnetic compatibility.
– complies with all the relevant provisions of the Directive 2011/65/EU relating to RoHS2.

– was designed and built in accordance with the following harmonised standards:

y NF EN 61326-1:2013 « Electrical equipment for measurement, control and
laboratory use – EMC requirements – Part 1: General requirements »
y NF EN 55011:2010/A1:2011 Class A

– was designed and built in accordance with the following other standards:

y NF EN 61000-4-2
y NF EN 61000-4-3
y NF EN 61000-4-4
y NF EN 61000-4-5
y NF EN 61000-4-6

ORIGINAL DECLARATION

Done in Beaune La Rolande on 16 May2017
Hervé LE COINTE
Quality Director

DC1-EN rev:A

EC Declaration of Conformity

EDH0199En2041 — 12/18 vi

MFA Series Miniature Linear Stages

Definitions and Symbols

The following terms and symbols are used in this documentation and also
appear on the product where safety-related issues occur.

General Warning or Caution

The exclamation symbol may appear in warning and caution tables in this
document. This symbol designates an area where personal injury or
damage to the equipment is possible.

The following are definitions of the Warnings, Cautions and Notes that may
be used in this manual to call attention to important information regarding
personal safety, safety and preservation of the equipment, or important
tips.

WA RN IN G

Warning indicates a potentially dangerous situation which can result in
bodily harm or death.

CAUTION

Caution indicates a potentially hazardous situation which can result in
damage to product or equipment.

NOTE

Note indicates additional information that must be considered by the
user or operator.

European Union CE Mark

The presence of the CE Mark on Newport Corporation equipment means
that it has been designed, tested and certified as complying with all
applicable European Union (CE) regulations and recommendations.

Warnings and Cautions

ATTENTIO N

This stage is a Class A device. In a residential environment, this device
can cause electromagnetic interference. In this case, suitable measures
must be taken by the user.

vii EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

Warnings

W

ARNING

The motion of objects of all types carries potential risks for operators.
Ensure the protection of operators by prohibiting access to the dangerous
area and by informing the personnel of the potential risks involved.

WA RN IN G

Do not use this stage when its motor is emitting smoke or is unusually
hot to the touch or is emitting any unusual odor or noise or is in any
other abnormal state.

Stop using the stage immediately, switch off the motor power and then
disconnect the electronics power supply.

After checking that smoke is no longer being emitted contact your
Newport service facility and request repairs. Never attempt to repair the
stage yourself as this can be dangerous.

WA RN IN G

Make sure that this stage is not exposed to moisture and that liquid does
not get into the stage.

Nevertheless, if any liquid has entered the stage, switch off the motor
power and then disconnect the electronics from power supply.

Contact your Newport service facility and request repairs.

WA RN IN G

Do not insert or drop objects into this stage, this may cause an electric
shock, or lock the drive.

Do not use this stage if any foreign objects have entered the stage.
Switch off the motor power and then disconnect the electronics power
supply.

Contact your Newport service facility for repairs.

WA RN IN G

Do not place this stage in unstable locations such as on a wobbly table or
sloping surface, where it may fall or tip over and cause injury.

If this stage has been dropped or the case has been damaged, switch off
the motor power and then disconnect the electronics power supply.

Contact your Newport service facility and request repairs.

WA RN IN G

Do not attempt to modify this stage; this may cause an electric shock or
downgrade its performance.

WA RN IN G

Do not exceed the usable depth indicated on the mounting holes (see
section “Dimensions”). Longer screws can damage the mechanics or
cause a short-circuit.

EDH0199En2041 — 12/18 viii

MFA Series Miniature Linear Stages

Caution

Only the MFA-CCV6 stage is compatible and can be used in a vacuum
environment up to 10-6hPa.

C

AUTION

Do not place this stage in a hostile environment such as X-Rays, hard
UV,… or in any vacuum environment.

CAUTION

Do not place this stage in a location affected by dust, oil fumes, steam or
high humidity. This may cause an electric shock.

CAUTION

Do not leave this stage in places subject to extremely high temperatures
or low temperatures. This may cause an electric shock.

• Operating temperature: +10 to +35 °C

• Storage temperature: -10 to +40 °C (in its original packaging)

CAUTION

Do not move this stage if its motor power is on.

Make sure that the cable to the electronics is disconnected before
moving the stage. Failure to do so may damage the cable and cause an
electrical shock.

CAUTION

Be careful that the stage is not bumped when it is being carried. This
may cause it to malfunction.

CAUTION

When handling this stage, always unplug the equipment from the power
source for safety.

CAUTION

When the carriage is in its end-of-run position, it is strongly recommended
not to go beyond this point as this may damage the stage mechanism.

CAUTION

Contact your Newport service facility to request cleaning and
specification control every year.

1 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

Miniature Linear Stages
MFA Series

1.0 —Introduction

This manual provides operating instructions for the stage that you have
purchased in the MFA Series:

1

)

REMARK

Vacuum compatible stage to 10

-

6

hPa. In this case, the max. speed and

load capacity have to be divided by two.

MFA-CC miniature linear stage.

RECOMMENDATION

We recommend you read carefully the chapter “Connection to
electronics” before using the MFA stage.

MFA stages in an XYZ configuration.

• MFA-CC

• MFA-CCV6

(

1)

• MFA-PP

• MFA-PPD

EDH0199En2041 — 12/18 2

MFA Series Miniature Linear Stages

2.0 —Description

Designed for space-limited applications and compact multi-axis
a

ssemblies, MFA Series linear stages supply very high resolution, single­axis translation in a low-cost, motorized package. Typical applications for
this stage are fiber optic alignment, laser diode research, bio-medical
applications and inspection systems.

MFA linear stages are available in two versions: The MFA-CC with a DC­m

otor, features an integrated gear-box and a motor mounted high
resolution 2,048 cts/rev rotary encoder. The high-resolution position
feedback and low-friction mechanical design ensures ultra-smooth motion
with 100 nm sensitivity. The DC motor supplies an optimized output torque
that permits the use of a lower ratio step-down gear allowing for faster
motion with higher reliability and lower backlash. Hence, the MFA-CC is the
recommended choice for applications that require small incremental
motion with high dynamic speed range and good repeatability. The MFA-PP
and MFA-PPD stepper motor versions are more economical solutions for
less demanding applications.

Travel limit switches prevent bearing damage from accidental over-travel.

MFA stages feature an all-steel construction that provides a higher
stiffness-to-weight ratio and lower thermal expansion compared to
aluminum designs. The result is superior performance in a smaller
footprint. The smooth motion of the MFA linear stages is further
accentuated by Newport's proprietary double-row linear ball bearing
design with bearing ways that are directly machined into the structural
frame of the stage. Compared to other solutions that use commercial
bearings, MFA linear stages have a higher load capacity and stiffness with
low pitch and yaw errors.

Another benefit of Newport's integrated bearing ways is the availability of
4 widely spaced mounting holes for base mounting and XY-assemblies.
This provides better stress distribution and allows for more rigid multi­axis combinations than other designs that provide only line contact with 2
mounting holes.

2.1 Design Details

Base Material Stainless Steel
Bearings Double row linear ball bearings
Drive Mechanism Backlash compensated leadscrew
Drive Screw Pitch 0.5 mm
Reduction Gear MFA-CC: 1:14
MFA-PP: 1:43
Feedback MFA-CC: Motor mounted rotary encoder; 2,048 cts/rev

MFA-PP: None
Limit Switches Optical switches
Origin Uses motor side limit for homing, typically <5 mm repeatability
Cable Length MFA-PP, MFA-PPD & MFA-CC: 3 m

MFA-CCV6: 1.5 m

3 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

3.0 —Characteristics

3.1 Definitions

Specifications of our products are established in reference to ISO 230
standard part II “Determination of accuracy and repeatability of
positioning numerically controlled axes”.

T

his standard gives the definition of position uncertainty which depends

on the 3 following parameters:

Absolute Accuracy

Difference between ideal position and real position.

Accuracy

Difference between ideal position and real position after the compensation
of linear errors.

Linear errors include: cosine errors, inaccuracy of screw or linear scale
pitch, angular deviation at the measuring point (Abbe error) and thermal
expansion effects. All Newport motion electronics can compensate for
linear errors.

The relation between absolute accuracy and on-axis accuracy is as follows:

Absolute Accuracy = Accuracy + Correction Factor

x Travel

Repeatability

Ability of a system to achieve a commanded position over many attempts.

Reversal Value (Hysteresis)

Difference between actual position values obtained for a given target
position when approached from opposite directions.

Minimum Incremental Motion (MIM or Sensitivity)

The smallest increment of motion a device is capable of delivering
consistently and reliably.

Resolution

The smallest increment that a motion device can theoretically move
and/or detect. Resolution is not achievable, whereas MIM, is the real
output of a motion system.

Yaw, P itch

Rotation of carriage around the Z axis (Yaw) or Y axis (Pitch), when it
moves.

The testing of accuracy, repeatability, and reversal error are made
systematically with test equipment in controlled environment (20±1°C).

A linear cycle with 21 data points on the travel and 4 cycles in each
direction gives a total of 168 points.

Guaranteed and Typical Specifications

Guaranteed maximum performance values are verified per Newport's A167
metrology test procedure. For more information, please consult the
metrology tutorial section in the Newport catalog or at www.newport.com

EDH0199En2041 — 12/18 4

MFA Series Miniature Linear Stages

3.2 Mechanical Specifications

NOTE

For the MFA-CCV6 vacuum compatible stage to 10

-6

hPa, the max. speed

and load capacity have to be divided by two.

CAUTION

To reach specifications stated, stages must be fixed on a plane surface
with a flatness of 5 µm.

3.3 Load Specification Definitions

Normal Load Capacity (Cz)

Maximum load a stage can move while maintaining specifications.

This value is given with speed and acceleration specified for each stage,
and with a load perpendicular to bearings.

Axial Load Capacity (±Cx)

Maximum load along the direction of the drive train.

Off-Centered Load (Q)

Maximum cantilever-load a stage can move: Q ≤Cz/(1 + D/a)

D: Cantilever distance.

a: Construction parameter

MFA-PP and MFA-PPD MFA-CC

Travel Range [in. (mm)] 1 (25)
Minimum Incremental Motion (µm) 0.1 0.1
Uni-directional Repeatability, Typical (Guaranteed) (µm) 0.12 (±0.25) ±0.08 (±0.15)
Bi-directional Repeatability, Typical (Guaranteed)

(1) (2)

(µm) ±0.2 (±0.75) ±0.15 (±0.75)

Accuracy, Typical (Guaranteed)

(1)

(µm) ±0.9 (±3.0) ±0.7 (±3.0)

Maximum Speed (mm/s) 0.3 (MFA-PP) 2.5

1.0 (MFA-PPD)

Pitch, Typical (Guaranteed)

(1)

(µrad)

(3)

±25 (±100)

Yaw, Typical (Guaranteed)

(1)

(µrad)

(3)

±30 (±50)

MTBF 10,000 h at a 1 kg load with a 20% duty cycle

1)

For the definition of Typical and Guaranteed specifications see “Motion Basics Terminology & Standards” Tutorial
at www.newport.com

2)

After backlash compensation.

3)

To obtain arcsec units, divide µrad value by 4.8.

G

U

A

R

A

N

T

E

E

D

S

P

E

C

I

F

I

C

A

T

I

O

N

S

5 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

3.4 Load Characteristics and Stiffness

NOTE

For the MFA-CCV6 vacuum compatible stage to 10-6hPa, the load
capacity has to be divided by two.

3.5 Stage Weights

The weight indicated is the average value for stages with their cable
installed.

The weight variation between drive units is not very significant.

MFA-CCV6 stage.

Weight [lb (kg)]
MFA 1.3 (0.6)

Cz, Normal centered load capacity (N) 50

-Cx, +Cx, Axial load capacity (N) 10
Kax, Compliance in roll (µrad/Nm) 60
Kay, Compliance in pitch (µrad/Nm) 10
Q, Off-center load (N) Q ≤Cz ÷ (1 + D/20)
Where D = Cantilever distance (mm)

C

z

Z

D

±

C

x

X

α

y

Y

α

z

Q

EDH0199En2041 — 12/18 6

MFA Series Miniature Linear Stages

4.0 —Drives and Motors

4.1 Stepper Drive Version

Stepper-motor-driven stages are offered in one half-step drive version:
M

FA-PP & MFA-PPD.

Micro-Step Drive

T

his is the drive for stepper or pulse-driven motors, transmitted by the

electronic unit, which entails a theoretical movement of the motor by one
fraction of a full-step. For these translation stages, the micro-step is
equivalent to 1/64 of the full-step.

Stepper Motor Performance Specifications and Characteristics

Command Signals for the Stepper Motor

4.2 DC-Motor Drive Version

One DC-motor-driven configuration is available: MFA-CC.

DC-Motor Performance Specifications and Characteristics

NOTE

For the MFA-CCV6 vacuum compatible stage to 10

-6

hPa, the max. speed

has to be divided by two.

Resolution

(1)

Speed Angle by Step RMS Current Resistance Inductance

(µm) (mm/s) (°) per Phase (A) (Ω) (mH)

MFA-PP 0.00757 0.3 15 0.25 12.5 5.5
MFA-PPD 0.00757 1.0 15 0.25 12.5 5.5

1

)

Micro-step driving.

0 2

-1

1

10.5 1.5

Step 1 2 3 4 5 8 7 8

+ Phase 1

+ + – – + + – –

– Phase 1

– – + + – – + +

+ Phase 2

– + + – – + + –

– Phase 2

+ – – + + – – +

Direction – MOTION

+

+ Phase 1

– Phase 1

+ Phase 2

– Phase 2

Direction +

Resolution Speed Nominal Max RMS Max. Peak Resistance Inductance Tachometer
(µm) (mm/s) Voltage (V) Current (A) Current (A) (Ω) (mH) Const. (V/krpm)

MFA-CC 0.0174 2.5 24 0.15 0.21 54.6 1.19 –

7 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

Command Signals for the DC-Motor

In the above drawings, + Motor signal is referred to – Motor signal.

➀

When the stage moves in + Direction, the + Motor voltage is higher than
– Motor voltage.

➁

When the stage moves in – Direction, the + Motor voltage is lower than
– Motor voltage.

4.3 Sensor Position

End-of-Run are 5 V open collector type.

CAUTION

“End-of-Run” are active signals and should not be connected to any other
source.

D

irection +

+V

+ Motor

– Motor

–V

MOTION Direction +

M

OTIONDirection –

–

EOR Limit

Travel Range

+

EOR Limit

Home Position

Direction – MOTION Direction +

EDH0199En2041 — 12/18 8

MFA Series Miniature Linear Stages

4.4 Feedback Signal Position

The incremental sensor consists of an optical scale and an encoder head.
When the carriage moves, the encoder head generates square signals in
quadrature and sends to pins #19, #20, #23 and #24 of the SUB-D25
connector.

“Encoder” are “differential pair” (type RS-422) type output signals. Using
these signals permits a high immunity to noise. Emission circuits generally
used by Newport are 26LS31 or MC3487. Reception circuits to use are
26LS32 or MC3486.

4.5 Pinouts

The pinout diagram for the MFA-PP stages mini-DIN9 connector is shown
below.

Pin #21

Pin #22

O

utput Signals

E

ncoder Phase B

Encoder Phase B

Encoders
& Sensors
P

ower Supply

+5 V 5%
150 mA max.

0

V

Pin #24

P

in #20

Encoder Phase A

E

ncoder Phase A

Pin #23

Pin #19

}

NEWPORT

STAGE

USER

Direction +

0

1

E

ncoder

P

hase A

0

1

Encoder
Phase A

1

234

0

1

Encoder
Phase B

0

1

E

ncoder

P

hase B

D

irection –

M

OTION Direction +

2

6

9

1

3

7

MFA-PP

1 – End-of-Run
2 Phase 1a
3 +5 V
4 Phase 2b
5 N.C.
6 Phase 2a
7 Phase 1b
8 Ground
9 + End-of-Run

9 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

The pinout diagrams for the MFA-PPD and MFA-CC stages SUB-D25M
connector are shown below.

1)

Pin #13 of SUB-D25M is reserved for internal logic for Newport
controller.

MFA-CC

1 N.C.
2 N.C.
3 N.C.
4 N.C.
5 + Motor
6 + Motor
7 – Motor
8 – Motor
9 N.C.
10 N.C.
11 N.C.
12 N.C.
13 Reserved

(

1)

14 Ground
15 N.C.
16 0 V
17 + End-of-Run
18 – End-of-Run
19 Encoder Phase A
20 Encoder Phase B
21 +5 V
22 0 V
23 Encoder Phase /A
24 Encoder Phase /B
25 N.C.

MFA-PPD

1 Phase 1a
2 N.C.
3 Phase 1b
4 N.C.
5 Phase 2a
6 N.C.
7 Phase 2b
8 N.C.
9 N.C.
10 N.C.
11 N.C.
12 N.C.
13 Reserved

(

1)

14 Ground
15 N.C.
16 0 V
17 + End-of-Run
18 – End-of-Run
19 N.C.
20 N.C.
21 +5 V
22 0 V
23 N.C.
24 N.C.
25 N.C.

1

3

25

14

1

EDH0199En2041 — 12/18 10

MFA Series Miniature Linear Stages

5.0 —Connection to Newport Controllers

5.1 Warnings on Controllers

Controllers are intended for use by qualified personnel who recognize
shock hazards and are familiar with safety precautions required to avoid
p

ossible injury. Read the controller user’s manual carefully before
operating the instrument and pay attention to all written warnings and
cautions.

WA RN IN G

Disconnect the power plug under the following circumstances:

• If the power cord or any attached cables are frayed or damaged in

any way.

• If the power plug is damaged in any way.

• If the unit is exposed to rain, excessive moisture, or liquids are spilled

on the unit.

• If the unit has been dropped or the case is damaged.

• If you suspect service or repair is required.

• Whenever you clean the electronics unit.

CAUTION

To protect the unit from damage, be sure to:

• Keep all air vents free of dir t and dust.

• Keep all liquids away from the unit.

• Do not expose the unit to excessive moisture (85% humidity).

• Read this manual before using the unit for the first time.

WA RN IN G

All attachment plug receptacles in the vicinity of this unit are to be of
the grounding type and properly polarized.

Contact your electrician to check your receptacles.

WA RN IN G

This product is equipped with a 3-wire grounding type plug.

Any interruption of the grounding connection can create an electric
shock hazard.

If you are unable to insert the plug into your wall plug receptacle,
contact your electrician to perform the necessary alterations to ensure
that the green (green-yellow) wire is attached to ear th ground.

WA RN IN G

This product operates with voltages that can be lethal.

Pushing objects of any kind into cabinet slots or holes, or spilling any
liquid on the product, may touch hazardous voltage points or short out
parts.

11 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

5.2 Connection

There is a label on every stage indicating its part and serial numbers.

W

ARNING

Always turn the controller's power OFF before connecting to a stage.

NOTE

These stages are ESP compatible. Enhanced System Performance is
Newport's exclusive technology that enables Newport ESP motion
controllers to recognize the connected Newport ESP stage and upload
the stage parameters. This ensures that the user can operate the motion
system quickly and safely.

5.3 Cables

MFA-PP, MFA-PPD and MFA-CC are delivered equipped with a 3-meter
cable, the MFA-CCV6 stage is delivered with a 1.5-meter cable.

These cables are equipped with a SUB-D25M connector for direct
connection to Newport Controllers.

WARNING

This cable is shielded correctly. For a correct operation, make sure to
lock connectors (ground continuity provided by the cable).

WARNING

Keep the motor cables at a safe distance from other electrical cables in
your environment to avoid potential cross talk.

BENDING

STATIC CABLE: ≥.94 (24)
CABLE IN MOTION: ≥2.76 (70)

ø.24

(6)

LOCKING

KNOBS

2.28 (58)

DISCONNECTED

CABLE

CONNECTOR

S

TAGE

SUB-D25 CONNECTOR SHOWN

DIMENSIONS IN INCHES (AND MILLIMETERS)

EDH0199En2041 — 12/18 12

MFA Series Miniature Linear Stages

6.0 —Connection to Non-Newport Electronics

6.1 MFA-PPD & MFA-CC Connections

WARNING

N

ewport is not responsible for malfunction or damage of MFA stages

when used with non-Newport controllers.

WARNING

Newport guarantees “ ” compliance of MFA stages only if used with
Newport cables and controllers.

It is the customer’s responsibility to modify the cable and take care of
sensor signal connections, when using the stage with non-Newport
controllers.

End-of-Runs and Mechanical Zero are open collector type with a 5.6 V
protective Zener diode.

Reserved
(EEPROM Enable):
I

in

max.: 10 mA

V max.: 30 V

NEWPORT STAGE
SUB-D25M CONNECTOR

+5 V

R

,

Pull-Up Resistor

End-of-Run:
I

in

max.: 16 mA

V max.: 5.6 V

NEWPORT STAGE

For connection to non-Newport electronics,
pin #17 and #18 End-of-Runs must be
connected to +5 V with a pull-up resistor. For
some non-Newport controllers, the +5 V
output signal may be pulled up internally.

+5 V

R

,

Pull-Up Resistor

Pin #17
Pin #18

Pin #13

5.6 V

To enable End-of-Run, when a MFA stage is
used with non-Newport controllers using the
S

ub-D25M connector provided, pin #13 must
be connected to +5 V with a pull-up resistor
(ex: 4.99 kΩ).

13 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

6.2 MFA-PP Stage

WARNING

T

he MFA-PP stage is equipped with a mini-DIN9 non-standard connector

and must only be used with our Newport NSC200 controller/driver.

NSC200 Single-Axis Low-Power

Motion Controller/Driver.

7.0 —Dimensions

1.89 (48)

.87

±.49

(22

±12.5

)

1.42
(36)

.79

(20)

5.26 (133.5)

.79
(20)

1.42
(36)

.79

(20)

.39 (10)

.98

(25)

1.42
(36)

1.77
(45)

CABLE LENGTH 9.8 FT (3 M)

4 HOLES C’BORED,

FOR 4-40 (M3) SCREW

4 HOLES M2 THD,
DEPTH: .12 (3)

2 HOLES M3 THD,
DEPTH: .20 (5)

6 HOLES M3 THD,
DEPTH: .20 (5)

MFA-PPD & MFA-CC:

SUB-D25M CONNECTOR

MFA-PP:

MINI-DIN9 CONNECTOR

MODEL SHOWN: MFA

DIMENSIONS IN INCHES (AND MILLIMETERS)

EDH0199En2041 — 12/18 14

MFA Series Miniature Linear Stages

8.0 —Accessories

N

OTE

These plates are not included with MFA stages and must be ordered
separately.

8.1 MFA-BK Plate

The MFA-BK top plate is used for XZ and XYZ assemblies with MFA stages.

8.2 (M-)MFA-TP Top Plates

8.3 MFA-BP Base Plate

6 HOLES ø.24 (6)

1.77
(45)

1.21

(30.65)

.38

(

9.65)

.31
(

8)

2.17 (55)

.79

(

20)

.79

(20)

1.42
(

36)

2 HOLES C’BORED

FOR 4-40 (M3) SCREW

4 HOLES C’BORED
FOR M2 SCREW

.24 (6)

4 HOLES C’BORED

FOR 4-40 (M3) SCREW

ON 1.42 x .79 (36 x 20)

6 HOLES 8-32 (M4) THD

1.0
(25)

2.48 (63)

2.0
(50)

1.26 (32)

1.0

(25)

.24
(6)

1.42
(36)

3.50 (89)

.24

(6)

.79

(20)

ø.79

(20)

1.42
(36)

1.97
(50)

4 HOLES C’BORED

FOR 4-40 (M3) SCREW

ON SQR .79 (20)

4 HOLES ø.26 (7,5)
ON 2.98

x 1.0 (75.8 x 25.4)

8 HOLES M3 THD

15 EDH0199En2041 — 12/18

MFA Series Miniature Linear Stages

9.0 —Maintenance

R

ECOMMENDATION

Please contact Technical Sales Support team for recommendations on
application specific maintenance.

9.1 Maintenance

The MFA stage requires no particular maintenance. Nevertheless, this is a
precision mechanical device that must be kept and operated with caution.

PRECAUTIONS

The MFA stage must be used or stocked in a clean environment, without
dust, humidity, solvents or other substances.

RECOMMENDATION

It is recommended to return the stage to Newport for re-lubrication after
2000 hours of use.

If the MFA stage is mounted on a workstation and cannot be easily
removed, please contact Newport's After Sales Service for further
instructions.

9.2 Repair

CAUTION

Never attempt to disassemble a component of the stage that has not
been covered in this manual.

To disassemble a non specified component can cause a malfunction of
the stage.

If you observe a malfunction in your stage, please contact us immediately
to arrange for a repair.

CAUTION

Any attempt to disassemble or repair a stage without prior
authorization will void your warranty.

9.3 Calibration

CAUTION

It is recommended to return your MFA stage to Newport once a year for
recalibration to its original specifications.

EDH0199En2041 — 12/18 16

MFA Series Miniature Linear Stages

17 EDH0199En2041 — 12/18

Your Lo ca l Rep re se nt at iv e

Tel .:
F

ax:

N

ame:

Company:

Address:

Country:

P. O . N u m b e r :

Item(s) Being Returned:

Model #:

Description:

Reasons of return of goods (please list any specific problems):

R

eturn authorization #:

(Please obtain prior to return of item)

Date:

Phone Number:

Fax Number:

Serial #:

Service Form

Visit Newport Online at:

www.newport.com

North America & Asia

Newport Corporation
1791 Deere Ave.

Irvine, CA 92606, USA

Sales

Tel.: [phone]
e-mail: [e-mail]

Technical Support

Tel.: [phone]
e-mail: [e-mail]

Service, RMAs & Returns

Tel.: [phone]
e-mail: [e-mail]

Europe

MICRO-CONTROLE Spectra-Physics S.A.S
9, rue du Bois Sauvage

91055 Évry CEDEX
France

Sales & Technical Support

Tel.: [phone]
e-mail: [e-mail]

Service & Returns

Tel.: [phone]