Congratulations and thank you for purchasing the NewHank Workmate mixer.
This mixer is a representationof NewHank’s continuing commitment to produce the best and highest quality
audio products possible at an affordable price-point.
Please carefully read and understand the instructions in this manual thoroughly before attempting to
operate this unit.
These instructions contain important safety information regarding the use and maintenance of this unit.
Take special care to follow all warning symbols and labels both on the unit and printed in this manual.
Please keep this manual with the unit, for future reference.
Do not discard the packing carton in the trash. Please recycle whenever possible.
KEY FEATURES
• 2U Compact Rack mount design • Stereo Master Balance Control
• USB/SD Audio Player (32GB Max) • Player reads both WAV and MP3 file formats
• Bluetooth audio connectivity to Media Player • All , Ra ndom and Single Play function
• Assignable crossfader section • 2 band EQ on line input channels
• Master output both on balanced XLR and RCA • Stereo Master Balance Control
• Microphone Gain , Treble and Bass Control • Adjustable individual ZONE Output
• Extremely clean signal to noise ratio
GETTING STARTED THE BASIC PRINCIPLES
1. Study the diagrams on page 4 and 5.
3. Make sure all devices are turned off and all faders, zone and gain rotary’s are set to "zero”.
4. Connect all your stereo input sources as indicated in Figure 2
on page 5.
5. Connect the stereo outputs to power amplifier(s), powered speakers and so on.
6. Plug all devices into AC power.
7. Always switch your system on in the following sequence:
1. Audio input sources (like DVD- CD Players, Tuners etc).
2. Mixer.
3. Amplifiers, Powered speakers etc.
Always switch your system off in reverse sequence:
1.Amplifiers, Powered speakers etc.
2.Mixer.
3.Audio input sources (like DVD- CD Players, Tuners etc).
26. CUE CH 1 - Sends the channel 1 pre-fader signal to the headphones when engaged.
27.CUE CH 2 - Sends the channel 2 pre-fader signal to the headphones when engaged.
28.CUE CH 3 - Sends the channel 3 pre-fader signal to the headphones when engaged.
29. CUE CH 4 - Sends the channel 4 pre-fader signal to the headphones when engaged.
30.MASTER MONITORING - Sends the Output signal to headphones when engaged.
31.HEADPHONES VOLUME- Adjusts the headphone output level.
32.HEADPHONES - 6.3MM Stereo Headphone connector.
33.POWER SWITCH -- Mains power ON/OFF switch. Before you turn on the power, be sure that you
have made all connections to the mixer. Also check that amplifiers are turned off. Remember mixer on
first and turned off last.
REAR PANEL CONNECTIONS
!
Figure 2
34. CH1 PHONO1 – Turntables can be connected to these jacks. The red colored RCA jack represents
the right channel input and the white jack the left channel input.
35. CH1 LINE1 -- Do not connect turntable’s to these jacks. CD players, Ta pe decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
36. CH2 AUX1 --Do not connect turntable’s to these jacks. CD players, Tap e decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
37. CH2 PHONO2 – Turntables can be connected to these jacks. The red colored RCA jack represents
the right channel input and the white jack the left channel input.
38. CH2 LINE2 -- Do not connect turntable’s to these jacks. CD players, Tap e decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
39. CH3 AUX2 -- Do not connect turntable’s to these jacks. CD players, Ta pe decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
40. CH3 LINE3 -- Do not connect turntable’s to these jacks. CD players, Tap e decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
41. CH3 MIC 1 -- Connect a microphone to this 6.3mm input.
42. CH4 AUX3 --Do not connect turntable’s to these jacks. CD players, Tap e decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
43. CH4 LINE4 --Do not connect turntable’s to these jacks. CD players, Tap e decks or other line level
sources can be connected. The red colored RCA jack represents the right channel input and the
white jack the left channel input.
44. CH4 MIC 2 -- Connect a microphone to this 6.3mm input.
45. REC- - Use this RCA fixed output signal for recording etc
46. MASTER -- Unbalanced RCA stereo output for short cable runs.
47. BALANCED XLR --Balanced stereo output for short and long cable runs.
48. BOOTH --Use this output signal to drive a booth monitor or separate sound
system. The output level for these 6.3mm jacks is controlled by the BOOTH volume knob(16).
49. IEC POWER SOCKET -- Connects to mains with the supplied power-cord.
SPECIFICATIONS
Installation: Place on flat surface or mount in 19" rack.
Power supply: Integrated transformer AC 230V-50Hz.
Power consumption: 1 2 W typical, 21W w/ full headphone output.
Operating Temperature: 5 to 35 deg. CC; Humidity: 25 to 85%.
!! ! ! ! (Non-condensing); Storage Temperature: -20 to 60 deg. C
Dimensions: 19" 2he Rack mount, Front 483x88mm Rear:438x85mm.
!! ! ! !
Please Note: All specifications and improvements to and in the design of this unit and its manuals are
subject to change at any time without any prior written or published notice.