Newco Vista Vend Installation Manual

Installation, Operation, Replacement Parts and Service Manual

Table of Contents

Product Compartment Loading........................................................................................................3

Installation........................................................................................................................................4

Operation..........................................................................................................................................5

Removal of Major Components.......................................................................................................6

Disassembly of Major Components.................................................................................................8

-Front Cover...........................................................................................................................8

-Product Trays........................................................................................................................9

-Control Heart ........................................................................................................................9

-Back Cover ...........................................................................................................................11

-Locking Cover......................................................................................................................11

-Carousel................................................................................................................................12

-Base.......................................................................................................................................12

Exploded Views ...............................................................................................................................13

-Control Box ..........................................................................................................................13

-Coin Box...............................................................................................................................15

-Back Shell.............................................................................................................................17

-Lock Cover ...........................................................................................................................19

-Door ......................................................................................................................................21

-Tray.......................................................................................................................................23

-Carousel................................................................................................................................25

-Base.......................................................................................................................................27

Specifications ...................................................................................................................................28

2

Fig 4

Fig 1

Level 1

Level 2

A

Product Compartment Loading

1. Product compartment segments are designed in 1/3 pie segments for easy removal from the Vendor. These
compartments telescope up after they are installed in the Vendor *See Figure 1. Once removed from the
Vendor the compartments collapse to the same level to allow for ease of loading *See Figure 2. The
product compartments are designed with individual bin dividers to allow larger products fit into the
product compartments, price is the same per product regardless if a bin divider (“A”) is used or not B *See

Figure 3. This allows flexibility when stocking the machine.

Fig 2 Fig 3

2. Product Compartments and coinbox are designed to fit into the cargo box, *See Figure 4.

3

Fig 1

Fig 2

Key Lock

A

Rotating Ring

C

Installation

1. Place Vista Vend on a sturdy, level, flat,
surface.

2. Plug the AC to DC Adaptor into a 120-volt
AC receptacle.

3. Plug the AC to DC Adaptor power cord into
the Vista Vend’s receptacle located on the
back of the lower left side. *See Figure 1

Power

Operation : Cash Box Removal

1. Unlock the front cover by inserting the key
into the lock and rotating it 1/4th turn
clockwise.

2. Remove the front cover by pressing in on the
lower right corner of the cover (“A”). Rotate
until cover has proper clearance for removal.
Lift the front cover from the vendor and set it
aside. *See Figure 2 *Note that the front
cover can be stored by setting it on the back
cover during route servicing.

3. Rotate the carousel by grasping the blue
rotation ring of the carousel and rotating it
until one of the three 120-degree segments of
trays is centered in the service opening.

4. Grasp the horizontal slot (“C”) in the center
of the top tray and lift the segment out of the
vendor. Set the segment of trays on a flat
surface and telescope all four trays down to
one level. *See Figure 3

Fig 3

Fig 4

5. Remove the coin box by rotating the coin box
counter-clockwise and aligning the “Remove­Install” arrow on the coin box with the
reference arrow below. Pull the coin box out

horizontally and set it aside. *See Figure 4

4

Fig 5

6. Reinstall the coin box by aligning the “Remove-Install” arrow with the reference arrow on the bottom
of the coin box support. Rotate the coinbox clockwise until the “operate arrow” is lined up with the
reference arrow below.

7. Reinstall the 120-degree tray segment by grasping the horizontal slot in the center of the smallest tray
and lifting it to telescope the segment of trays up. Reinsert the tray segment into the vendor. Make
sure each of the four trays in the 120-degree segment are at the same height as the trays on the right
side and on the left side. If the trays are not the same height, the tray is not properly seated, and the
vendor will not operate.

8. Reinstall the front cover by placing it over the service opening and rotating the cover to the left until it
stops.

9. Turn the key counter clockwise ¼ turn to lock.

Operation : Product Purchase

1. To purchase a product from the Vista Vend,
rotate the carousel clockwise or counter­clockwise by grasping the carousel rotating ring
and select a product to purchase. The product
you wish to purchase should be in the “Vend
Zone” *See Figure 5

2. Align the right side of the compartment
containing the desired product with the right
side of the door opening. *See Figure 6

3. Refer to the price posted on the tray level
containing the desired product.

4. Deposit coins in the coin box until enough credit
has been accumulated on the coin box display to
purchase the desired product.

5. Push the colored, numbered (1,2,3,4) button on
the coin box that corresponds to the color of the
door handle located above the product to be
purchased. *See Figure 7

Fig 7

Fig 6

5

6. Grasp the door handle of the same color as the button that was pushed and move the door to the left until

the door stops.

7. Reach in and retrieve the product.

8. After removing the product, close the door by moving the door all the way back to the right.

Removal of Major Components

1. Unlock the front cover by inserting the key into
the lock and rotating it 1/4th turn clockwise.

2. Remove the front cover by pressing in on
the lower right corner of the cover has proper
clearance for removal. Lift the front cover from
the vendor and set it aside. *See Figure 7
*Note that the front cover can be stored by
setting it on the back cover during route
servicing.

3. Rotate the carousel by grasping the rotation ring

of the carousel and rotating it until one of the
three 120-degree segments of trays is centered
in the service opening.

4. Grasp the horizontal slot in the center of the top

tray and lift the segment out of the vendor. Set
the segment of trays on a flat surface and
telescope all four trays down to one level.
*See Figure 8

Fig 7

Fig 8

5. Remove the coin box by rotating the coin box

counter-clockwise and aligning the “Remove­ Install” arrow on the coin box with the
reference arrow below. Pull the coin box out
horizontally and set it aside. *See Figure 9

Fig 9

6

6. Remove the 3 screws on the left side of the
service opening that secures the locking cover
assembly. *See Figure 10

7. Remove the locking cover assembly by lifting it
vertically. *See Figure 11

8. Grasp the back-up slide arm (gray color) and
push up until the lock member arm (gray color)
can be separated from the back-up connect
blocks (gray color). *See Figure 12

9. Remove the 4 screws on the left side and the 5
screws on the right side of the control heart
assembly. *See Figure 13

10. Push in at the bottom of the right side of the
control heart assembly and snap the control
assembly off the back cover.

11. To remove the back cover, remove the screw
located below the coin box support at the top of
the steel tube. Remove the 2 screws at the
bottom left side of the back cover and rotate the
back cover counter-clockwise until the tabs
along the bottom perimeter of the cover are
clear of the tabs on the base. *See Figure 14

12. Grasp the back cover on the top with the right
hand and spread the lower left side of the cover
out with the left hand. Lift the back cover from
the base.

13. To remove the carousel, retract each detent
wheel (dark purple color) slightly and lift the
carousel enough above the detent wheel, so the
detent wheel can move under the carousel and
release the spring tension.

14. After both detent wheels are released under the
carousel, lift the carousel off the base. Remove
the thrust washer located on the steel tube under
the carousel.

Fig 10

Fig 11

Fig 12

Fig 13

Fig 14

7

15. Remove the detent wheels from the base by
sliding the wheels out from the center until they
clear the retaining tabs of the base. Lift out the
detent wheel, the spring applicator (dark purple
color), and the spring.

Fig 15

16. To remove the lock member arm (gray color)
and the lock member latch (gray color), remove
spring and then lift them vertically from the
base. * See Figure 15

17. Remove the lock member rocker (gray color)
by rotating the lock member rocker to the left
until it snaps out of the retaining bosses on the
base. Remove the rocker spring from the base.

Disassembly of Major Components

FRONT COVER:

1. Remove the door brackets B or C from each door by removing the screw on the back of the door bracket.

2. Remove the door handles by removing the screw on the underside of the handle.

3. Remove the doors by sliding them to the left and out of the front cover.

4. Remove the door vanes from the door by removing the mounting screws.

5. Remove all 4 lever covers from the front cover
by removing the screws underneath the lever
covers.

6. Remove all 8 door levers. Note: Lever “L” is
used on all 4 levels on the left side of the front
cover, and “R-1” is used on levels 1, 2, & 3 on
the right side of the cover. “R-2” is used on
level 4 on the right side of the front cover.

7. Remove the 3 front cover latches located on the
left side of the front cover by removing the
mounting screws form the back of the latches.

8. To reassemble the front cover, perform the
above steps in reverse order.

8

PRODUCT TRAYS:

1. To disassemble a product tray segment, telescope all trays down to one level, grasp the largest tray, and lift

it off the other trays. Repeat this process for the remaining trays.

2. To assemble the product trays, grasp the smallest tray and slide the second smallest tray down over the “T”

tabs of the smaller tray. Repeat this process for the remaining trays.

CONTROL HEART:

1. Turn the control heart assembly upside-down with the upper and lower cams (green color) facing up.

2. Remove the nut and lock washer from both cams. Remove the mounting screws from the two metal cross

braces and set cross braces aside.

3. Remove the upper and lower cam and also remove both metal cam bushings.

*Note: The upper cam has the shorter step and the lower cam has the longer step.

4. Turn the control heart assembly face up and remove the back-up actuator (gray color) by unsnapping it

from the mounting bosses.

5. Slide the back-up slide arm (gray color) up until the notch at the bottom of the slide arm lines up with the

horizontal round boss above. Continued on the next page.

9

6. Lift the back-up slide arm from the control heart assembly. Note: The round boss is used to hold the

back-up spring during testing and service only. Remove and attach the back-up spring below on the side of
the lock member arm (gray color) for vending operations.

7. Move the lower cam slide arm (green color) back until the notches at the bottom of the lower slide arm line

up with the retaining tabs above. Lift the lower cam slide arm up to clear the retaining tabs, and then pull
the lower cam slide arm back horizontally to remove.

8. Pull the upper cam slide arm back and lift it out of the control heart assembly.

9. To remove the lock slide arm, turn the control heart assembly upside- down. Remove the screw and

metal arm from the bottom of the lock. Turn the assembly back upright, and lift the slide arm off the
vertical side of the control heart assembly. Slide the lock slide arm back horizontally and remove. To
reinstall the lock slide arm, perform the above steps in reverse.

10. To remove the lock, remove the retaining nut and the lock from the control heart assembly. To reinstall the
lock, perform the above steps in the reverse order.

11. Remove the back up connect blocks from the control heart assembly by pulling them up and snapping them

from their mounting bosses.

12. Remove the lock (orange color) of the back-up actuator (gray color) by pulling the lock to the side enough

to free the pin from the hole and turn the lock ¼ turn and slide the lock off the spring. The spring can be
removed from the back up actuator by twisting and pulling on the spring at the same time.

13. Remove the lock (orange color) of the back-up actuator (gray color) by pulling the lock to the side enough

to free the pin from the hole and turn the lock ¼ turn and slide the lock off the spring. The spring can be
removed from the back up actuator by twisting and pulling on the spring at the same time.

1. Remove the back-up actuator assembly (gray color).

2. Remove the four lever springs and remove the screw to the right of the 4 door latches (orange color).

Lift the steel latch shaft on the free end and pull horizontally to remove. Then remove the 4 latches (orange
color).

3. Remove the back-up push arm for key (orange color) by prying up gently on each end until it pops out.

4. Remove the shaft for the “V” actuators (orange color) by prying up on the right end of the shaft. Pop it up
and remove it horizontally.

5. Remove the 4 press springs and the 4 press plates (orange color).

6. Remove the 4 “V” actuators by pulling up on the push key (orange color) and sliding the “V” actuators off
to the side. Remove the four push keys.

7. To re-assemble the door latch system, perform the above steps in reverse.

10

Back Cover

LOCKING COVER:

1. Remove bracket “L” and bracket “R” by removing the mounting screws.

2. Remove the 3 “U” nuts from the locking cover upper section by spreading the nuts enough to clear their

mounting hole and pulling them off.

3. To remove the locking cover upper section from the locking cover lower section, remove the 5 mounting

screws and pull the covers off.

Locking Cover

BACK COVER:

1. Remove mounting plate “C” with attached circuit board and unplug the power cord.

2. Remove the coin box support by rotating it clockwise.

3. Remove connecting plate “A” from the back cover by removing the 8 mounting screws.

4. Remove the connection plate “B” by removing the mounting screw.

11

Base

CAROUSEL:

1. To remove the two center pieces from the 6 tray supports, free one slot at a time in the center piece by
squeezing the 2 prongs of the tray support together and pulling the center piece away from the prongs
while holding pressure on the center piece to keep other depressed prongs from re-latching. Do this on
all 6 slots of the center piece, and it will pull free from the tray supports.

2. To remove the 6 tray supports from the carousel, squeeze the 2 prongs together (through the slots in the

carousel), and pull the tray supports out of the carousel slots.

BASE:

1. To remove the carousel rollers, lift the rollers from their retaining bosses on the base.

2. The roller shaft can be removed from the rollers by removing one of the “E” clips.

3. Remove the steel tube from the base by removing the screw at the base of the tube.

4. Remove the feet from the base by removing the two screws and the wing nut on top of the base. Remove

the foot cup and the foot base from underneath the base.

5. The electrical wire that supplies power to the coin box can be removed by pulling the wire down out of the

steel tube and out from underneath the tabs on the base. Also, remove the nut on the jack on the lower left
side of the base. Pull the wire and the jack out of the base.

Carousel

12

101 121020 LOWER CAM POM GREEN PMS347C 1
102 121021 UPPER CAM POM GREEN PMS347C 1
103 121022 LOWER CAM SLIDE ARM POM GREEN PMS347C 1
104 121023 UPPER CAM SLIDE ARM POM GREEN PMS347C 1
105 121024 BACKUP SLIDE ARM POM GREY PMS424C 1
106 121049 CONTROL HEART SUPPORT-A PC BLACK 1
107 121050 CONTROL HEART SUPPORT-B PC BLACK 1
108 121107 BACKUP SPRING OD8x42, DIA0.8 Ni-PLATED 1
109 121025 BACKUP CONNECT BLOCK POM GREY PMS424C 2
110 121026 LATCH - A POM ORANGE PMS021C 2
111 121108 CAM LOCK J-35834-CAM-TBD-14 1
112 121109 KEY 2
113 121027 LOCK SLIDE ARM POM GREY PMS424C 1
114 121110 LATCH SHAFT POLE STEEL DIA3.2x48.5 Ni-PLATED 1
115 121111 SCREW FOR LATCH STAINLESS STEEL M4x15PA 1
116 121112 LEVER SPRING OD4.0x28, DIA0.5 N-PLATED 4
117 121028 "V"ACTUATOR FOR LATCH POM ORANGE PMS021C 4
118 121001 NO 4.PUSH KEY POM ORANGE PMS021C 1
119 121002 NO 3.PUSH KEY POM ORANGE PMS021C 1
120 121003 NO 2.PUSH KEY POM ORANGE PMS021C 1
121 121004 NO 1.PUSH KEY POM ORANGE PMS021C 1
122 121113 SHAFT FOR"V"ACTUATOR DIA3.2x43.5 Ni-PLATED 1
123 121114 PRESS SPRING OD6.6x14.4, DIA0.4 Ni-PLATED 4
124 121005 PRESS PLATE POM ORANGE PMS021C 4
126 121012 BACKUP PUSH ARM FOR KEY POM ORANGE PMS021C 1
127 121115 SPRING OF BACK UP ACTUATOR OD4.4x16.1, DIA0.7 Ni-PLATED 1
128 121029 BACKUP ACTUATOR POM GREY PMS424C 1
129 121013 LOCK OF BACKUP ACTUATOR POM ORANGE PMS021C 1
130 121116 SCREW STAINLESS STEEL M3x8BT 4
131 121117 STEEL BUSHING DIA12.1xDIA12.9x16.7 Ni-PLATED 2
132 121118 HEXAGON SCREW M5x32 Ni-PLATED 2
134 121119 SPRING WASHER M5x9.0x1.3 Ni-PLATED 2
135 121120 E RING ETW-2.3 ACP 2
136 121121 HEXAGON NUT M5x(8)x4mm Ni-PLATED 2
137 121079 LATCH - B POM ORANGE PMS021C 1
138 121095 LATCH - C POM ORANGE PMS021C 1
140 121105 FIX BRACKET-A STEEL T=1.2mm Zn-PLATED 1
141 121106 FIX BRACKET-B STEEL T=1.2mm Zn-PLATED 1
142 121122 SCREW SYAINLESS STEEL M3x10PM 4
143 121123 FLAT WASHER ID3.3xOD10xT0.9 Ni-PLATED 4
144 121124 SPRING WASHER M3xOD5x0.7 Ni-PLATED 4
145 121125 FLAT WASHER ID4.2xOD9xT0.6 Ni-PLATED 1
146 121126 SPRING WASHER ID4.1xOD7.6x1.0 Ni-PLATED 1
147 121127 SILICON FLUID SF1000 1g

13

14

201 121073 COIN BOX-UPPER ABS BLACK 1
202 121074 COIN BOX-LOWER ABS BLACK 1
203 121075 COIN TRAY-A PC RED PMS199C 1
204 121076 COIN TRAY-B PC RED PMS199C 1
205 121077 MOUNTING PLATE-A ABS BLACK 1
206 121078 MOUNTING PLATE-B ABS BLACK 1
208 121082 LOCK POLE PA66 BLACK 1
209 121083 LENS PC CLEAR RED PMS#194C 1
210 121080 PRESS PLATE - LEVER ABS PINK PMS182C 1
211 121086 LOCK POLE KEY POM BLACK 1
212 121084 PUSH HANDLE PC COOL GREY PMS#11U 1
213 121087 PUSH LEVER POM L. PURPLE PMS263C 4
214 121085 LOCK WASHER PC COOL GREY PMS#11U 1
215 121088 PUSH KEY #1 POM BLUE PMS300C 1
216 121089 PUSH KEY #2 POM BLUE PMS300C 1
217 121090 PUSH KEY #3 POM BLUE PMS300C 1
218 121091 PUSH KEY #4 POM BLUE PMS300C 1
219 121081 PCB BRACKET ABS PINK PMS182C 1
220 121098 INFRARED TRANSMITTER PMMA CLEAR 1
221 121128 PIN-PUSH KEY SPP1.5x6 BLACK OXIDE 5
222 121129 SCREW STAINLESS STEEL M2.3x6PT 5
223 121130 SCREW STAINLESS M2.6x10PT 5
224 121131 SCREW STAINLESS STEEL M3x8PT 1
225 121132 SCREW STAINLESS STEEL M3x10PA 4
226 121133 SPRING A - COIN BOX OD7.4x26.1 DIA0.6 Ni-PLATED 1
227 121134 SPRING B - COIN BOX OD4.3x17.1, DIA0.3 Ni-PLATED 1
228 121135 ELECTRICAL CONTROL ASSEMBLY 1
229 121136 TRANSFORMER PRI: 120V 60Hz, SEC: 0.5A DC12V 1
230 121137 SCREW STAINLESS STEEL M3x10KA 3
231 121138 SCREW STAINLESS STEEL M3x6PT 2
232 121139 SCREW STAINLESS STEEL M2x5PM 9
233 121140 SCREW STAINLESS STEEL M2x5KM 1
234 121101 LOCK LATCH POM BLACK 1
235 121102 LATCH COVER POM BLACK 1
236 121141 SPRING-LOCK LATCH OD6.1x14, DIA0.3 Ni-PLATED 2
237 121142 SCREW STAINLESS STEEL M2.6x12KA 2

15

16

219 121081 PCB BRACKET ABS PINK PMS182C 1
222 121129 SCREW STAINLESS STEEL M2.3x6PT 5
301 121063 BACK SHELL PCTA DS2010 CLEAR 1
302 121072 COINBOX SUPPORT PC BLACK 1
303 121051 CONNECTING PLATE-A PC BLACK 1
304 121030 CONNECTING PLATE-B PC BLACK 1
305 121068 HOUSING-LEVEL PC CLEAR 1
306 121069 BASE-LEVEL ABS WHITE 1
307 121070 COVER-LEVEL ABS WHITE 1
308 121143 SCREW STAINLESS STEEL M3x12PA 5
309 121144 BABY OIL 4mL 4mL
310 121099 PRESS BRACKET-A POM BLACK 3
311 121100 PRESS BRACKET-B POM BLACK 2
312 121145 SCREW STAINLESS STEEL M3x10KA 1
313 121146 SCREW STAINLESS STEEL M4x15PA 1
314 121147 SCREW STAINLESS STEEL M5x16PA 2
315 121148 FLAT WASHER ID3.3xOD10xT0.9 Ni-PLATED 6
316 121149 SPRING WASHER M3xOD5x0.7 Ni-PLATED 25
317 121150 FLAT WASHER ID3.3xOD8xT1.0 Ni-PLATED 19
318 121151 SCREW STAINLESS STEEL M3x14PT 21
319 121152 FLAT WASHER ID4.2xOD9xT0.6 Ni-PLATED 1
320 121153 SPRING WASHER M4.1xOD7.6x1.0 Ni-PLATED 1

17

18

401 121071 LOCKING COVER UPPER PC BLACK 1
402 121060 LOCKING COVER LOWER PC BLACK 1
403 121031 BRACKET --L PC BLACK 1
404 121032 BRACKET --R PC BLACK 1
405 121154 U--TYPE NUT STEEL 13x22,T=0.7 Ni-PLATED 3
406 121155 SCREW STAINLESS STEEL M5x16PA 3
407 121156 SCREW STAINLESS STEEL M3x10PA 11

19

20

501 121064 FRONT SHELL PCTA DS2010 CLEAR 1
502 121061 NO.4 DOOR PC CLEAR 1
503 121062 NO.3 DOOR PC CLEAR 1
504 121052 NO.2 DOOR PC CLEAR 1
505 121053 NO.1 DOOR PC CLEAR 1
506 121033 DOOR HANDLE POM YELLOW PMS108C 1

121033 POM PURPLE PMS252C 1
121033 POM GREEN PMS368C 1

121033 POM BLUE PMS285C 1
507 121034 DOOR LATCH--A POM BLACK 1
508 121035 DOOR LATCH--B POM BLACK 3
509 121036 LEVER--L POM GREY PMS424C 4
510 121037 LEVER--R1 POM BLACK 3
511 121038 LEVER--R2 POM BLACK 1
512 121054 NO.4 LEVER COVER PC BLACK 1
513 121055 NO.3 LEVER COVER PC BLACK 1
514 121056 NO.2 LEVER COVER PC BLACK 1
515 121057 NO.1 LEVER COVER PC BLACK 1
516 121039 NO.4 DOOR VANE POM BLACK 1
517 121040 NO.3 DOOR VANE POM BLACK 1
518 121041 NO.2 DOOR VANE POM BLACK 1
519 121042 NO.1 DOOR VANE POM BLACK 1
521 121043 SCREW BRACKET -B POM BLACK 1
522 121044 SCREW BRACKET -C POM BLACK 2
523 121157 SCREW STAINLESS STEEL M3x12KA 4
524 121158 SCREW STAINLESS STEEL M3x12PA 3
525 121159 RIVET SCREW STAINLESS STEEL M3x5BB 14
526 121160 SCREW STAINLESS STEEL M3x10KA 16

21

22

601 121018 LEVER 4# TRAY ABS CLEAR 3
602 121019 LEVER 3# TRAY ABS CLEAR 3
603 121016 LEVER 2# TRAY ABS CLEAR 3
604 121017 LEVER 1# TRAY ABS CLEAR 3
605 121014 REMOVABLE DIVIDER--A ABS CLEAR 24
606 121015 REMOVABLE DIVIDER--B ABS CLEAR 24

23

24

701 121065 CAROUSEL PCTA DS2010 CLEAR 1
702 121045 CENTRE PIECE PC BLACK 2
703 121046 TRAY SUPPORT PC BLACK 6
704 121092 STEEL TUBE OD25x179, T=1.0 CHROME 1
705 121006 INSERT--A POM BLACK 2
706 121007 INSERT--B POM BLACK 24
707 121008 THRUST WASHER POM BLACK 1
708 121093 "U" RING RUBBER BLACK 1
709 121161 SCREW STAINLESS STEEL M5x8PM 2
710 121162 GLUE GB-404CPU 10g 10g
711 121163 GLUE GB-899 1.0g 1.0g

25

26

108 121107 BACKUP SPRING OD8x42, DIA0.8 Ni-PLATED
801 121066 BASE ABS BLACK 1
802 121009 ROLLER TPE NATURAL 6
803 121164 SHAFT ROLLER STEEL DIA5x24.5 Ni-PLATED 6
804 121058 DETENT WHEEL TPE DARK PURPLE PMS253C 2
805 121165 DETENT SPRING OD13.3x60 DIA1.5 Ni-PLATED 2
806 121067 DETENT SPRING APPLICATOR POM DARK PURPLE PMS253C 2
807 121166 LOCK WASHER ETW-4 ACP 12
808 121011 FOOT BASE POM BLACK 6
809 121010 FOOT CUP POM BLACK 6
810 121094 FOOT RUBBER BLACK 6
811 121167 WING BOLT M6 STEEL M6x30 Ni-PLATED 6
812 121168 NUT M6 M6 Ni-PLATED 6
814 121169 STEEL BUSHING ID7.5xOD9.5x20 1
815 121103 DETENT WHELL PIPE POM WHITE 2
816 121104 ROLLER PIPE POM WHITE 6
817 121170 SCREW STAINLESS STEEL M3x10PT 12
818 121171 SPRING OD8.7x15, DIA1.2 Ni-PLATED 6
819 121172 FLAT WASHER ID6.4xOD12.5xT1.0 Ni-PLATED 6
820 121173 SILICON FLUID SF1000 2g
901 121059 LOCK MEMBER ARM POM GREY PMS424C 1
902 121047 LOCK MEMBER LATCH POM GREY PMS424C 1
903 121174 SPRING OF LATCH OD6.6x14.4, DIA0.6 Ni-PLATED 1
904 121048 ROCKER OF LOCK MEMBER POM GREY PMS424C 1
905 121175 SPRING OF ROCKER OD7.4x18, DIA0.6 Ni-PLATED 1

27

28