Newco AKH-1, AKH Installation Manual

N E W C O E N T E R P R I S E S

INSTALLATION and OPERATION MANUAL

For AKH SERIES BREWERS

6Man Pt No 110326

REV.10-01

AKH-D

BREWER SPECIFICATIONS

Model
AKH-1 1 8-1/2" 16 3/8" 16 15/16
AKH-2 2 8-1/2" 16 3/8" 18 9/16
AKH-3 3 15-1/2" 16 3/8" 16 15/16

AKH-AP N/A 8-1/2" 16 3/8" 22 15/16

AKH-D N/A 8-1/2" 17 3/8” 21 3/16
AKH-LD N/A 8-1/2" 17 3/8” 21-3/8
AKH-TC N/A 8-1/2" 17 3/8” 17 5/8
AKH-TT N/A 8-1/2" 17 3/8” 16 15/16

No of

Warmers Width Length Height*

AKH-3

INSTALLATION INSTRUCTIONS

as indicated on serial tag. For (AKH Thermal Model)Turn master

WARNING: - Read and follow installation instructions before plugging or wiring in machine to electrical circuit.

Warranty will be void if machine is connected to any voltage other than that specified on the name plate.

1) Plug or wire brewer to appropriate voltage circuit
switch, located on rear of brewer, to the ON position.

2) (AKH warmer model), make sure warmer switches are in the OFF position. Place one of the empty decanters on the
warmer located below the brew basket. For (AKH thermo model) pump style airpots, remove the pump stem. Place
the empty dispenser into position below the brewbasket

3) Raise the top evaporation cover and pour ONE decanter (on AKH warmer model) or pitcher (on AKH thermo model)
of water through the pour-in grid into basin.

4) (AKH warmer model), Turn lower warmer/brew switch to the ON or BREW position to start brew cycle.
NOTE: Float assembly will prevent heat pump from activating if water is not present in the basin. This first pot will
be a few ounces short due to some water retention in the system.

5) Machine is now ready to use and will yield a full pot on following brew cycles.

COFFEE PREPARATION PROCEDURES

1) Place the filter into brew basket.

2) Place the appropriate amount of ground coffee into the filter for the volume of coffee to be brewed.

3) Slide the brew basket into holder.

4) For warmer units:

Place empty decanter on warmer located directly under the brew basket
Turn corresponding warmer switch to ON position.
For airpots or other dispensers
Remove any non brew thru lids or pump stems
Place airpot under brew basket.

5) Raise the top evaporation cover and pour ONE decanter(warmer model) or pitcher(therm model) of COLD water
through the pour in grid into the basin. Turn lower warmer / brew switch to the ON position to start the brew cycle.

(AKH warmer model), Brew cycle may be canceled by turning the rocker switch back to the off position.

(AKH thermo model), The brew cycle may be canceled by turning the master switch located on the rear of the
brewer to the off position.
NOTE: Never pour hot water into the brewer. This brewer features a European style brewing system which heats
only the water for coffee when you pour it into the brewer. This type of system does not have a tank to store hot
water. Do not overfill unit by pouring in more than one decanter of water at a time.

6) Hot water will be delivered through the sprayhead. This distributes the hot water evenly over the coffee bed within
the brew basket. The coffee brew will drain from the brew basket into the decanter below.

7) The unique thermal brew system takes a little longer to brew than tank systems, which allow the stored water to
become stale, but the result is better tasting and hotter coffee.

8) (AKH warmer model) TURN OFF WARMERS WHEN NOT IN USE. Red light in switch indicates when warmer is
ON.

9) To clean brew basket simply remove from brew rails and dump filter into waste basket. The brewing process, as
described above, can now be started again.

10 To clean brew basket simply remove from brew rails and dump filter into waste basket. The brewing process, as
described above, can now be started again.

INSTALLATION INSTRUCTIONS (CONTINUED)

2