NewAir AC10100H, AC10100E User Manual

ELECTRICAL SAFETY

• This appliance is for indoor use only.

• Always turn off the unit and unplug it when not in use.

• Do not use this unit in excessively humid or wet environments.

• Do not pull or place strain on the power cord when moving the appliance.

• IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY AN ELECTRICIAN

OR SPECIALIZED TECHNICIAN AUTHORIZED BY THE MANUFACTURER IN ORDER
TO PREVENT FIRE.

FOR MAXIMUM EFFICENCY

• Do not exceed the recommended room size.

• Make sure doors and windows are closed while the portable air conditioner is in use.

Also keep curtains and blinds closed during the sunniest parts of the day while the air
conditioner is in operation.

• Frequently clean the portable air conditioner’s filters.

• Once the room or area has reached your desired comfort level, be sure to reduce the

unit’s temperature and ventilation settings.

2

14″

extend it with your own hose, as this

Mounting of the Exhaust Pipe

• Only use the hose provided and
clip exhaust hose to the back of
the air conditioner.

• Avoid kinks and bends in the
exhaust hose. This can cause
moist air to accumulate, causing
the unit to overheat and shut
down.

• The exhaust hose may be
extended from 12 inches (300mm)
to 59 inches (1500mm), but for
maximum cooling efficiency use
the shortest length possible.

WARNING!

The included exhaust hose is
specifically designed to fit the
specifications of this unit. Do not

can cause the air conditioner to
malfunction.

5

carbon filter from its

Installation of the Carbon Filter

1. Remove the filter frame from the unit.

2. Separate the filter fixer from the filter
frame.

3. Remove the activated
plastic bag.

4. Attach the activated carbon filter to the
filter frame.

5. Reattach the filter fixer onto the filter
frame (the activated carbon filter should
be placed between the filter frame and
filter fixer firmly).

6. Insert the filter set (filter frame + activated
carbon filter + filter fixer) into the back of
the unit.

FIG.13

6

Setting the Model/Function:

Press the MODE button to select the desired mode (cooling, fan or heating).

Setting Temperature

1. Press 'Temperature up' or 'Temperature down' button to change the set temperature.

2. The display window will indicate the set temperature. If not, the temperature displayed will
show the ambient room temperature.

3. Please note that the preset temperatures are as follows:

Cooling: 75oF (24oC)

Heating: 68oF (20oC)

Setting Fan/Ventilation Speed:

1. Press SPEED button to select the desired fan speed (high or low). The indicator light will
display the fan speed selected.

2. If the unit is in AUTO mode, it will choose the ventilation speed automatically according to
the ambient temperature (the related indicators will light on). In the AUTO mode the fan
speed cannot be changed manually.

Setting Timer

1. Press TIMER button to set the desired number of operating hours (from 1 to 12 hours).
When the set time has been reached, the machine will turn off automatically. The display
window will show the hour(s) you set as you press TIMER button. If the TIMER is not set,
the unit will work continuously.

2. By pressing the timer without turning on the other functions, you can PRE-SET the number
of hours to be delayed before the unit turns on. For example, if you set the timer to “2”, the
unit will automatically turn on after 2 hours.

Sleep Function

1. When in cooling mode, press the SLEEP button. The set temperature will increase 2oF (1oC)
on the 1st hour; another 2oF (1oC) on the second hour, and then maintain that temperature.

2. When in heating mode, press the SLEEP button. The set temperature will decrease 2oF
(1oC) on the 1st hour; another 2oF (1oC) on the second hour, and then maintain that
temperature.

3. In sleep mode, the fan will automatically be set to low. By pressing the SLEEP button again,
the set temperature and fan speed will revert back to the previous setting.

4. The unit will shut down automatically after it has been in sleep mode for 12 hours.

5. Please note the sleep function is not available while the machine is working in AUTO
or FAN (ventilation) mode. It will only work in cooling or heating mode.

8

Heating Function (For AC-10100H Only)

1. When the air conditioner is in heating mode, ambient warm air is recycled and used to heat

your immediate area. The exhaust pipe will still need to be fitted onto the unit in order
for the cold air to be removed.

2. Continuous drain is compulsory while the unit is in heat mode. Working range for heating

function is 45 to 77oF (7 ~ 25oC). If the ambient temperature is lower than this range, the unit
may not work properly.

All the functions can also be performed with the supplied remote control. The remote

control requires 2 AAA batteries to operate.

Regulating air flow direction

Move the air vent directly to adjust the air flow direction
of the louvers.

Please Note:

1. To prolong the life of the compressor, after turning off the unit, please wait at least 3
minutes before turning it back on.

2. The cooling system will turn off if the ambient temperature is lower than the set temperature.
However, the fan will continue operating at the set level. Once the ambient temperature
rises above the set temperature, cooling will resume.

3. The heating system will turn off if the ambient temperature is higher than the set
temperature. The ventilation fan will continue operating at the set level. Once the ambient
temperature drops below the set temperature, heating will resume.

4. This machine is equipped with ANTI-FROST function. When using the heating function in
low temperature the heater will occasionally stop heating in order to melt any frost that has
accumulated within the air conditioner. Normal operation will resume in a few moments.

9

DRAINING THE UNIT

During the cooling process, some water will be extracted from the air and stored within the unit’s
water reservoir.

If the reservoir is full, both the compressor and motor will stop and the unit will beep (press any

button to stop the beeping sound). The full water tank indicator light will also start flashing.

To resume cooling, empty the reservoir by following these steps:

1. Turn off the air conditioner and unplug it

from the wall socket. To prevent water
leakage, avoid moving the unit when full.

2. Place a container (such as a small pan)

underneath the drain hole.

3. Remove the drain knob & rubber plug from

the drain hole and allow the water to drain
out.

4. When the container is almost full, replace

the rubber plug in the drain hole and empty
the water tray.

5. Repeat until the unit is emptied.

6. Replace the rubber plug and make sure it is

firmly in place.

7. Turn the unit back on. The full tank indicator

light should turn off.

For Continuous Drainage:

• Remove the drain knob and rubber plug
from the drainage port and hold on to them
for future use.

• Connect the drain tube to the water outlet
as shown. Place the other end of drain
tube into a drain.

10

• The drain tube may be extended by
adding an extension tube with a
suitable connector.

Please Note:

Drain tube

1. The drain must be at or below the level

of the drainage port.

2. The full water tank indicator light will
not work when the unit is being
continuously drained.

3. To extend the drain tube, you can
connect it with another hose with an
overall diameter of approximately 0.7”
(18mm).

11

Original drain
tube

Extension tube
(OD: 0.7”)

MAINTENANCE INSTRUCTIONS

Always unplug the air conditioner from the power supply before cleaning. To
maximize the efficiency of the air conditioner, regularly clean the unit.

Cleaning the Housing:

• Use a soft, damp cloth to wipe the body clean.

• Never use aggressive chemicals, gasoline, detergents, chemically treated cloths, or other

cleansing solutions. These all could possibly damage the cabinet.

Cleaning the Filter:

• Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters.
Rinse thoroughly under running water (no hotter than 104oF or 40oC).

• Thoroughly dry the filter before replacing it back into the unit.

• PLEASE NOTE: NEVER USE THE UNIT WITHOUT THE AIR FILTER.

End of Season Storage:

• Completely drain any condensed
water from the unit.

• Set the air conditioner on fan made
(ventilation only) for a few hours to dry
the inside of the unit.

• Clean or change the filter.

• Unplug and store the power cord as

shown.

• Place the unit back in its original
carton and store it in a clean, dry
area.

Cord

12

15