Nevion CWDM-18 User Manual

CWDM-18
User manual
Rev. B
Nevion
Nordre Kullerød 1 3241 Sandefjord Norway Tel: +47 33 48 99 99
nevion.com
CWDM-18 Rev. B
Nevion Europe P.O. Box 1020
3204 Sandefjord, Norway Support phone 1: +47 33 48 99 97 Support phone 2: +47 90 60 99 99
Nevion USA
1600 Emerson Avenue
Oxnard, CA 93033, USA
Toll free North America: (866) 515-0811
Outside North America: +1 (805) 247-8560
E-mail: support@nevion.com
See http://www.nevion.com/support/ for service hours for customer support globally.
Rev.
Repl.
Date
Sign
Change description
B A 2015-06-10
MR
Added figure 2.
A 0 2015-05-25
MB
Template update; DoC removed
0 - 2011-03-24
MR
Initial version
Nevion Support
Revision history
Current revision of this document is the uppermost in the table below.
nevion.com | 2
CWDM-18 Rev. B
Contents
Revision history .......................................................................................................... 2
1 Product overview ..................................................................................................... 4
2 Specifications .......................................................................................................... 5
2.1 Optical specifications ....................................................................................................... 5
3 Mounting the CWDM module into frame .................................................................. 6
4 Laser safety precautions .......................................................................................... 9
General environmental requirements for Nevion equipment..................................... 10
Product Warranty ...................................................................................................... 11
Appendix A – Materials declaration and recycling information .................................. 12
A.1 Materials declaration ......................................................................................................12
A.2 Recycling information .....................................................................................................12
nevion.com | 3
CWDM-18 Rev. B
Common Not used 1271nm 1291nm 1311nm 1331nm 1351nm 1371nm 1391nm 1411nm 1431nm 1451nm 1471nm 1491nm 1511nm 1531nm
Shutters at upper row are due to high signal strength at “common” port
1 Product overview
The Flashlink CWDM (Coarse Wavelength Division Multiplexing) system is based on an all­optical module for multiplexing and demultiplexing 18 CWDM wavelengths according to ITU­T G.694.2. The unit works similarly in both directions and can be used as mux as well as demux.
Figure 1. CWDM filter scheme.
Figure 2. Backplane layout.
nevion.com | 4
CWDM-18 Rev. B
Number of channels
18
Available wavelengths (nm)
1271, 1291, 1311, 1331, 1351, 1371, 1391, 1411, 1431, 1451, 1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611
Connector
LC/UPC
Insertion loss (end to end, including connectors)
4dB typical
5.4dB max
Channel Spacing
20nm
Passband
13nm min
Transmission circuit fibre
9/125um single mode
Adjacent Channel Isolation
30dB min
Non-Adjacent Channel Isolation
40dB min
Directivity
45dB min
Connector Return loss
45dB min
Polarization depending loss
0.2dB max
Ripple in passband
0.5dB max
Operating Temperature
0 – 70 oC
Storage Temperature
-40 – 85 oC
Optical Power
300mW max
2 Specifications
2.1 Optical specifications
nevion.com | 5
CWDM-18 Rev. B
3 Mounting the CWDM module into frame
The CWDM filter must be mounted in a Flashlink sub rack. This is done from the rear. Do not use force when inserting the CWDM filter. The module’s main board has a special design to utilize both card rails in the FL sub rack. In order to enter the lower rail before sliding the unit into its final position, please follow the method shown in the pictures below.
Figure 3.1. Enter the module with angle.
Figure 3.2. PCB tag inside the power bus PCB.
nevion.com | 6
CWDM-18 Rev. B
Figure 3.3. Opposite side of PCB tag.
Figure 3.4. Adjust to normal position.
nevion.com | 7
CWDM-18 Rev. B
Figure 3.5. Slide the module to final position using both card rails.
Figure 4. Module mounted in frame
nevion.com | 8
CWDM-18 Rev. B
1
4 Laser safety precautions
These are guidelines to limit hazards from laser exposure. All the available EO units in the Flashlink range include a laser. Therefore this note on laser safety should be read thoroughly even though there is no laser
onboard this product. The lasers emit light at wave lengths between 1271 nm and 1611 nm. This means that the
human eye cannot see the beam, and the blink reflex cannot protect the eye. (The human eye can see light between 400 nm to 700 nm).
A laser beam can be harmful to the human eye (depending on laser power and exposure time). Therefore:
Be careful when connecting / disconnecting fibre pigtails (ends). Never look directly into the pigtail of the laser/fibre. Never use microscopes, magnifying glasses or eye loupes to look into a fibre
end. Use laser safety goggles blocking light between 1271 nm and at 1611 nm
Instruments exist to verify light output power: Power meters, IR-cards etc. Flashlink features: The FR-2RU-10-2 is classified as Class 1 laser product according to EN 60 825-1:94/A11:96,
and CFR Ch1 (1997) Part 1040.10. If the front panel is removed, the FR-2RU-10-2 is classified as Class 1 laser product
according to EN 60 825-1:94/A11:96, and class IIIb according to CFR Ch1 (1997) Part
1040.10. Maximum output power1: 17 mW Operating wavelengths: > 1260 nm
Max power is for safety analysis only and does not represent device performance.
nevion.com | 9
CWDM-18 Rev. B
1.
The equipment will meet the guaranteed performance specification under the following environmental conditions:
-
Operating room temperature range:
0°C to 50°C
-
Operating relative humidity range:
<90% (non-condensing)
2.
The equipment will operate without damage under the following environmental conditions:
-
Temperature range:
-10°C to 60°C
-
Relative humidity range:
<95% (non-condensing)
General environmental requirements for Nevion equipment
nevion.com | 10
CWDM-18 Rev. B
Product Warranty
The warranty terms and conditions for the product(s) covered by this manual follow the General Sales Conditions by Nevion, which are available on the company web site:
www.nevion.com
nevion.com | 11
CWDM-18 Rev. B
組成名稱
Part Name
Toxic or hazardous substances and elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
六价铬
Hexavalent
Chromium
(Cr(VI))
多溴联苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
CWDM-18
O O O O O
O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.
Appendix A – Materials declaration and recycling information
A.1 Materials declaration
For product sold into China after 1st March 2007, we comply with the “Administrative Measure on the Control of Pollution by Electronic Information Products”. In the first stage of
this legislation, content of six hazardous materials has to be declared. The table below shows the required information.
This is indicated by the product marking:
A.2 Recycling information
Nevion provides assistance to customers and recyclers through our web site
http://www.nevion.com/. Please contact Nevions Customer Support for assistance with
recycling if this site does not show the information you require. Where it is not possible to return the product to Nevion or its agents for recycling, the
following general information may be of assistance:
Before attempting disassembly, ensure the product is completely disconnected from
power and signal connections.
All major parts are marked or labeled to show their material content. Depending on the date of manufacture, this product may contain lead in solder. Some circuit boards may contain battery-backed memory devices.
nevion.com | 12
Loading...