Neutrik NBNC75BFG7, NBNC75BJP9 User Manual

75 Ohm BNC Connectors
77
Content Page
Rear Twist Cable Connectors ................................... 79
Push Pull Cable Connectors ..................................... 81
Accessories ............................................................ 83
Cable to Connector Guide ...................................... 84
Connector to Cable Guide ...................................... 86
Chassis Connectors ................................................ 88
With the introduction of HD signals the impedance of BNC con­nectors becames more important than ever. Every deviate imped­ance has a negative influence on the „return loss“ / „VSWR“ (Voltage Standing Wave Ratio) which are important measure­ments for reflected signals in a transmission line. Especially on high frequencies - as they occur when transmitting HD signals (typical transmission @ 2.25 GHz) - an impedance mismatch results in a lot of return loss. Neutrik´s BNC connectors feature a true 75 design that meet the stringent requirements of HDTV and sustain a consistent impedance at high frequencies up to 3 GHz. To achieve this result every Neutrik
®
BNC connector has been adapted to the measurements of a small group of cables, this guarantees the best possible performance and a little return loss.
The higher the frequencies the more pronounced is the „skin effect“, which means that the energy moves to the outside of the conductor. Therefore the plating of outer and center contact is more important than on audio connectors with low frequen­cies - both contacts of our BNC connectors are gold plated.
True 75 HDTV Connectors
2005 VERSION with enhanced high frequency shielding!
78
NEUTRIK® 75BNC Connectors
Frequency [MHz]
Return Loss [-dB]
0 500 1000 1500 2000 2500 3000
-45
-40
-35
-30
-25
-20
Frequ. RL
[GHz] [dB]
1 39.83 2 34.17 3 32.82
Neutrik® offers a variety of 75 Ω cable and chassis BNC connectors. The Push-Pull and RearTwist® cable connectors are easy to handle in high density applications such as video patchbays and switches, provide a tactile and fast assembly and offer colour coding as a standard. All parts of our BNC series are precisely machined to our high quality standards.
In times of rising frequencies the connector shielding becomes to an important value in order to avoid EMI problems and cross­talking. The 2005 version takes this fact into account and has been equipped with an optimized ground contact design for maximum shielding effectiveness.
-20
Screeningatten./ [-dB]
Frequency [GHz]
-30
-40
-50
-60
-70
-80
-90
-100
1.11.21.41.6 1.82.02.22.42.6 2.83.0
Gold plated ground contact with improved shielding effectiveness optimized for high frequency HDTV signal up to 3 GHz.
Look for the Logo
79
www.neutrik.com
Rear Twist Cable Connectors
“Rear Twist® Principle” locking/unlocking using the easily accessible soft touch boot (Patent DE 100 48507)
Ideal for recessed bulkheads where access to the “head” of the connector might be an issue. These connectors turn from
the back and not the front.
True 75 Ω design meets the stringent HDTV / DVD requirements
Snug-fit center pin insert provides tactile feedback
Shield and jacket crimp technology prevents the problem of an exposed grounding braid on cable assemblies
Excellent cable protection and retention
Large version for RG 11 cable
Precise Swiss machined brass parts for outstanding durability
Accessories include color coded boots in 10 standard colours, crimp tool and dies
Sleek female cable jack e.g. for Y-cables
Mountable panel version of cable jack for fixed installations
Rear Twist® (Standard, Large & Tiny) and Cable Jacks
NBTC75BLI4 NBNC75BLP7 NBNB75GLP9 NBTB75CFI4
to identify the original
Features & Benefits
For further technical information
80
Rear Twist Cable Connectors
Screen and cable jacket crimp instead of
screen crimp only. Grooved inner surface holds the cable jacket to prevent tearing braids.
Rear Twist
®
boot in 10 colours for easy access in high density applications.
Leading area: Avoids tilting due to side forces to
protect the contacts from deformation. Guarantees a lifetime of min. 1`000 mating cycles!
Gold plated ground contact with improved
shielding effectiveness optimized for high frequency HDTV signal up to 3 GHz.
81
www.neutrik.com
please refer to www.neutrik.com
Push Pull Cable Connectors
Unique Push-Pull locking system is ideal for ultra high density applications, patching, etc.
True 75 design meets the stringent HDTV / DVD requirements
Excellent return loss / VSWR data
Precision machined parts
Assembly is fast and easy and requires only a standard center contact crimp after cable preparation
Reusable due to screw lock strain relief
Snug-fit center pin insert provides tactile feedback
Only pin crimp, this eliminates the need of different crimp dies and facilitates field repair
Innovative screw lock cable retention for easy assembly
Accessories include colour coded boots in 10 standard and 3 translucent colours
Push Pull Cable Connectors
NBNC75PTS11 NBNC75PNS7 NBNC75PIE9 NBNC75PLS9
Push Pull Cable Connectors
Features & Benefits
82
Gold plated ground contact with improved
shielding effectiveness optimized for high frequency HDTV signal up to 3 GHz.
Leading area: Avoids tilting due to side forces to
protect the contacts from deformation. Guarantees a lifetime of min. 1`000 mating cycles!
Neutrik
®
chuck type strain relief offers
flexibility and field repair.
Push Pull sleeve in various colours for easy
access in high density applications.
Push Pull locking mechanism for convenient handling,
perfect for patching applications.
Look for the Logo
Accessories
83
www.neutrik.com
Boots, tools, ...
BNC tool case equipped with
- HX-R-BNC
- PT-BNC: Plier tool
- CS-BNC: Stripping tool
HX-R-BNC DIE-R-BNC-*CAS-BNC-T Note: Dies have to be ordered separately.
Crimp tool, frame
Crimp tool die for pin and shield for HX-R-BNC
BST-BNC-* BS-BNC-* HX-BNC DIE-BNC-*
HT-BNC DSS
Boot for Push-Pull BNCs in black, 9 different colours available, as well as 3 trans lucent variants.
Crimp tool, frame. (heavy duty) Crimp tool die for pin and shield
for HX-BNC.
Spanner tool for the Push-Pull BNCs.
Lettering plate for D Shape­bulkheads.
Crimp die assignment for HX-BNC Crimp die assignment for HX-R-BNC
Crimp die Hex crimp Hex crimp Center pin
mm inch mm
A B C A B C (square crimp)
DIE-R-BNC-PDC 6.47 4.53 4.06 0.255 0.178 0.160 1.6 DIE-R-BNC-PG 6.47 5.00 - 0.255 0.197 - 1.6 DIE-R-BNC-PJ 6.47 5.41 - 0.255 0.213 - 1.6 DIE-R-BNC-PS 6.47 7.01 - 0.255 0.276 - 1.6 DIE-R-BNC-PU 6.47 7.36 - 0.255 0.290 - 1.6 DIE-R-BNC-PY 6.47 8.23 - 0.255 0.324 - 1.6 DIE-R-BNC-Z 9.73 - - 0.383 - - 1.75
(Hex crimp)
Crimp die Hex crimp Hex crimp Center pin
mm inch mm
A B A B (square crimp)
DIE-BNC-CS 4.06 7.01 0.160 0.276 1.6 DIE-BNC-JD 5.41 4.53 0.213 0.178 1.6 DIE-BNC-PG 6.47 5.00 0.255 0.197 1.6 DIE-BNC-S 7.01 - 0.276 - 1.6 DIE-BNC-U 7.36 - 0.290 - 1.6 DIE-BNC-Y 8.23 - 0.324 - 1.6
Standard boot for the Rear Twist
®
BNCs in black, 9 different colours available.
to identify the original
SCF
Rubber sealing cover to protect the connector agains dust and moisture
SCDX
Hinged cover seals D-size chas­sis connectors, IP54 rated
84
For further technical information
Cable to Connector Guide
Push Rear Rear Twist Cable Jack Cable Jack Hex Crimp Pull Twist Tiny Tiny Panel in mm
Belden
CANARE
COMMSCOPE
CANFORD
GEPCO
DRAKA MULTIMEDIA CABLE
L-4CFB NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 L-5CFB NBNC75BYY11 8.23 LV-61S NBNC75PNS7 NBNC75BLP7 6.47 LV-77S NBNC75BYY9 8.23 V(3-5)-3C NBNC75PGE7 NBNC75BGG7 5.00 V(3-5)-4CFB NBNC75PLE9 NBNC75BJJ9 5.41 V(3-5)-5C NBNC75PVS9 NBNC75BRS9 7.01 V(3-5)-5CFB NBNC75PVS11 NBNC75BWS11 7.01 L-1.5C2VS NBTC75BLI4 4.06
2065V NBNC75PIE9 NBNC75BIJ9 5.41 2279V NBNC75PQS11 NBNC75BQP11 6.47 5563 NBNC75PNS7 NBNC75BLP7 6.47 5565 NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 5765 NBNC75PTS11 NBNC75BTU11 7.36 7536 (03-05) NBTC75BXX6 5.00 7538 NBNC75PDE6 NBNC75BDD6 4.53
VPM2000 NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 VSD2001 NBNC75PTS11 NBNC75BTU11 7.36
0.31 / 1.45 AF, 753-1304(2), 755-1302 NBTC75BFI4 NBTB75CFI4 4.06
0.41 / 1.9 AF, 753-1104, 755-1103, 755-1101 NBTC75BNN5 NBTB75CNN5 4.53
0.51 / 2.3 Dz, 757-1001, VADN 7243 NBTC75BVX6 5.00
0.6 / 2.8 AF, 0.6 L / 2.8 AF NBNC75PFE7 NBNC75BFG7 5.00
0.6 / 3.7, 0.6L / 3.7 NBNC75PNS7 NBNC75BLP7 6.47
0.6 / 3.7 Dz NBNC75PNS7 NBNC75BLS7 6.47
1277R, 1278R, 1279R NBTC75BNN5 4.53 1406B, 1407B, 1417B NBTC75BVV5 5.00 1426A NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 1505A NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 1505F NBNC75PLS9 NBNC75BJP9 6.47 1506A NBNC75PIE9 NBNC75BIJ9 5.41 1520A, 1521A, 1522A, 179DT NBTC75BFI4 NBTB75CFI4 4.06 1694A NBNC75PTS11 NBNC75BTU11 7.36 1694F NBNC75BTY11 8.23 1695A NBNC75PQS11 NBNC75BQP11 6.47 1855A NBNC75PDE6 NBNC75BDD6 4.53 1865A NBTC75BXX6 5.00 1855ENH NBNC75PFE7 NBNC75BFG7 5.00 7731A NBLC75BVZ17 9.73 8218 NBTC75BXX5 5.00 8241 NBNC75PNS7 NBNC75BLP7 6.47 8241F NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 8281 NBNC75BXY9 8.23 8281F NBNC75BYY9 8.23 9221 NBTC75BLI4 4.06
SDV, SDM NBNC75PFE7 NBNC75BFG7 5.00 SDV-L, SDV-F NBNC75PVS11 NBNC75BWS11 7.01 SDV-HD NBLC75BVZ17 9.73 SDV-F-HD NBNC75BWU13 7.36
85
www.neutrik.com
please refer to www.neutrik.com
Cable to Connector Guide
Push Rear Rear Twist Cable Jack Cable Jack Hex Crimp Pull Twist Tiny Tiny Panel in mm
DRAKA MULTIMEDIA CABLE
SUHNER
OTHERS
0.8 / 3.7 AF, 755-801(803, 804) NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47
0.8 / 4.9 Dz NBNC75BXY9 8.23
1.0 / 4.8 AF, 75 5-901/5, Image 1000 NBNB75PTS11 NBNC75BUU11 NBNB75GUU11 7.36
1.2L / 4.8Dz, 1.2L / 4.95AF NBNC75BWU13 7.36
1.4 / 6.6 AF NBLC75BSX14 9.73
1.6 / 7.3AF NBLC75BVZ17 9.73
G02233 NBTC75BFI4 NBTB75CFI4 4.06 G04233D NBNC75PNS7 NBNC75BLS7 7.01 S02223 NBTC75BLI4 4.06 S04233, S04263 NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 S05133-07 NBNC75PTS11 NBNC75BTU11 7.36 S05163-02 NBNC75PTS11 NBNC75BTU11 7.36
AT&T 735 NBTC75BSS5 4.53 COMM-TEC RGBHV NBTC75BSS5 4.53 BBC PSF 1/3* NBNC75PNS7 NBNC75BLS7 7.01 CAE MC75 NTBC75BLI5 NBTB75CLI5 4.06 CAE MC75.39 NBTC75BVX6 5.00 CAE KX6A NBNC75PNS7 NBNC75BLP7 6.47 CAE VCB75 NBNC75PNS9 NBNC75BNP9 6.47 CAE VCB 100 NBNC75BXU13 7.36 Cordial CVI 3-7 NBNC75PFE7 NBNC75BFG7 4.53 Cordial CVI 06-28 NBNC75PFE7 NBNC75BFG7 5.00 Cordial CVI (CVM) 06-37 NBNC75PNS7 NBNC75BLP7 6.47 COVID CVD 1300-1500 NBTC75BLI5 NBTB75CLI5 4.06 ELF Inc. cable NBNC75PTS11 NBNC75BWS11 7.01 Eupen 705 CRT 5V-HS/ELF NBNC75PTS11 NBNC75BTS11 7.36 Inc. Cable NBNC75PTS11 NBNC75BTS11 7.36 Extron BNC-5HR NBTC75BNN5 NBTB75CNN5 4.53 Extron BNC-5RC NBNC75PGE7 NBNC75BFG7 5.00 Helix 734 NBNC75PNS9 NBNC75BNP9 6.47 Helix 735 NBTC75BSS5 4.53 Hirschmann KOKA 712Cu NBNC75PTS9 NBNC75BTS9 6.47 Kansai 0.5M3C-2V NBNC75PGE7 ­Kansai 3C-5S NBNC75PFE6 NBNC75BFH6 5.00 KLOTZ V06/28, VMXx75Y NBNC75PFE7 NBNC75BFG7 5.00 V06/37 NBNC75PNS7 NBNC75BLP7 6.47 V10/48 NBNB75PTS11 NBNC75BUU11 NBNB75GUU11 7.36 V16/72 NBLC75BVZ17 9.73 KROSCHU (341 270, 341 280) NBTC75BLI4 4.06 RG11 NBLC75BVZ17 9.73 RG59B/U NBNC75PNS7 NBNC75BLP7 6.47 RG179B/U NBTC75BLI4 4.06 SOMMER 600-0051 (M/L/S) NBNC75PNS7 NBNC75BLP7 6.47 600-0054 (M/L/S) NBNC75PNS7 NBNC75BLP7 6.47 600-0101M NBNC75PFE7 NBNC75BFG7 5.00 600-0104M NBNC75PFE7 NBNC75BFG7 5.00 600-162(F) NBNC75PLS9 NBNC75BLP9 6.47 600-025* -03 (05) 600-0701 600-020* -03 (05)
NBTC75BLI5 NBTB75CLI5 4.06
600-0451 NBNC75PLS9 NBNC75BLP9 NBNB75GLP9 6.47 600-0751 NBTC75BVX6 5.00 Wisi MK 99A NBNC75PVS12 NBNC75BWS12 7.01 ZNK CM14B NBTC75BFI4 NBTB75CFI4 4.06
* Registered trademark of BBC
86
For further technical information
Connector to Cable Guide
Pin crimp Hex crimp Inner
Insulator Cable O.D.
mm (square) mm Conductor
PUSH PULL
NBNC75PDE6 1.6 N / A
<
0.6
<
2.65 4.0 - 5.0
NBNC75PFE6 1.6 N / A
<
0.6
<
2.85 4.0 - 5.0
NBNC75PFE7 1.6 N / A
<
0.7
<
2.85 4.0 - 5.0
NBNC75PGE7 1.6 N / A
<
0.7
<
3.2 4.0 - 5.0
NBNC75PIE9 1.6 N / A
<
0.9
<
3.5 4.0 - 5.0
NBNC75PLE9 1.6 N / A
<
0.9
<
3.65 4.0 - 5.0
NBNC75PLS9 1.6 N / A
<
0.9
<
3.65 6.0 - 7.0
NBNC75PNS7 1.6 N / A
<
0.7
<
3.75 6.0 - 7.0
NBNC75PNS9 1.6 N / A
<
0.9
<
3.75 6.0 - 7.0
NBNC75PQS11 1.6 N / A
<
1.1
<
4.3 6.0 - 7.0
NBNC75PTS9 1.6 N / A
<
0.9
<
4.6 6.0 - 7.0
NBNC75PTS11 1.6 N / A
<
1.1
<
4.6 6.0 - 7.0
NBNC75PVS9 1.6 N / A
<
0.9
<
4.9 6.0 - 7.0
NBNC75PVS11 1.6 N / A
<
1.1
<
4.9 6.0 - 7.0
NBNC75PVS12 1.6 N / A
<
1.2
<
4.9 6.0 - 7.0
REAR TWIST
NBLC75BVZ17 1.75 (Hex crimp) 9.73
<
1.7
<
8.0
<
10.4
NBLC75BSX14 1.75 (Hex crimp) 9.73
<
1.4
<
6.6
<
9.5
NBNC75BDD6 1.6 4.53
<
0.6
<
2.8
<
4.3
NBNC75BFG7 1.6 5.00
<
0.7
<
3.1
<
4.7
NBNC75BFH6 1.6 5.00
<
0.6
<
3.1
<
4.9
NBNC75BGG7 1.6 5.00
<
0.7
<
3.2
<
4.7
NBNC75BIJ9 1.6 5.41
<
0.9
<
3.6
<
5.3
NBNC75BJJ9 1.6 5.41
<
0.9
<
3.8
<
5.3
NBNC75BJP9 1.6 6.47
<
0.9
<
3.8
<
6.3
NBNC75BLP7 1.6 6.47
<
0.7
<
3.8
<
6.3
NBNC75BLP9 1.6 6.47
<
0.9
<
3.8
<
6.3
NBNC75BLS7 1.6 7.01
<
0.7
<
3.8
<
6.9
NBNC75BNP9 1.6 6.47
<
0.9
<
4.1
<
6.3
NBNC75BQP11 1.6 6.47
<
1.1
<
4.5
<
6.3
NBNC75BRS9 1.6 7.01
<
0.9
<
4.8
<
6.9
NBNC75BTS9 1.6 7.01
<
0.9
<
4.7
<
6.9
NBNC75BTS11 1.6 7.01
<
1.1
<
4.7
<
6.9
NBNC75BTU11 1.6 7.36
<
1.1
<
4.7
<
7.3
NBNC75BTU11 1.6 7.36
<
1.1
<
4.7
<
7.3
NBNC75BTY11 1.6 8.23
<
1.1
<
4.7
<
8.0
NBNC75BWS11 1.6 7.01
<
1.1
<
5.1
<
6.9
NBNC75BWS12 1.6 7.01
<
1.2
<
5.1
<
6.9
NBNC75BWU13 1.6 7.36
<
1.4
<
5.1
<
7.3
NBNC75BXU13 1.6 7.36
<
1.4
<
5.1
<
7.3
NBNC75BXY9 1.6 8.23
<
0.9
<
5.1
<
8.0
NBNC75BYY9 1.6 8.23
<
0.9
<
5.2
<
8.0
NBNC75BYY11 1.6 8.23
<
1.1
<
5.2
<
8.0
REAR TWIST TINY
NBTC75BFI4 1.6 4.06
<
0.4
<
1.6
<
2.9
NBTC75BLI4 1.6 4.06
<
0.4
<
1.8
<
2.9
NBTC75BLI5 1.6 4.06
<
0.5
<
1.8
<
2.9
NBTC75BNN5 1.6 4.53
<
0.5
<
2.0
<
3.1
NBTC75BSS5 1.6 4.53
<
0.5
<
2.3
<
3.4
NBTC75BVV5 1.6 5.00
<
0.5
<
2.5
<
3.8
NBTC75BVX6 1.6 5.00
<
0.6
<
2.5
<
4.0
NBTC75BXX5 1.6 5.00
<
0.5
<
2.6
<
4.0
NBTC75BXX6 1.6 5.00
<
0.6
<
2.6
<
4.0
CABLE JACKS (TINY & PANEL VERSION)
NBTB75CFI4 1.6 4.06
<
0.4
<
1.6
<
2.9
NBTB75CNN5 1.6 4.53
<
0.5
<
2.0
<
3.1
NBTB75CLI5 1.6 4.06
<
0.5
<
1.8
<
2.9
NBNB75GLP9 1.6 6.47
<
0.9
<
3.8
<
6.3
NBNB75GUU11 1.6 7.36
<
1.1
<
4.9
<
7.3
87
www.neutrik.com
please refer to www.neutrik.com
Connector to Cable Guide
Cable Type
Belden 1855A; CommScope 7538 Kansai 3C-5S Belden 1855ENH; Cordial CVI 06-28, CVI 3-7; Canford SDM, SDV-LFH; Draka 0.6/2.8 AF, 0.6L/2.8 AF; Sommer 600-0101M, 600-0104M, KLOTZ V06/28, VMXx75Y Canare V(3-5)-3C; Extron BNC-5RC Belden 1506A; CommScope 2065V Canare V(3-5)-4CFB Belden 1505A, Belden 1505F; 8241F; CommScope 5565; Canare L-4CFB; Draka 0.8/3.7 AF, 755-801 (803,804); Gepco VPM2000; Suhner S04263; Sommer 600-0451, 600-162(F), 804) Belden 8241; BBC PSF 1/3, CAE KX6A; CommScope 5563; Cordial CVI (CVM) 06-37; Suhner G04233D; Canare LV-61S; RG59B/U; Draka 0.6/3.7, 0.6/3.7 Dz, 0.6L/3.7; Sommer 600-0051 (M,L,S), 600-0054 (M,L,S), KLOTZ V06/37 CAE VCB75; Helix 734 Belden 1695A; CommScope 2279V Hirschmann KOKA 712Cu Belden 1694A; CommScope 5765; Draka 1.0/4.8 AF, 755-901/5, Image 1000; Eupen 705 CRT 5V-HS; Gepco VSD2001; Suhner S05133-07 S05163-02, KLOTZ V10/48 Canare V(3-5)-5C Canare V(3-5)-5CFB; Canford SDV-F, SDV-L Wisi MK 99A
Belden 7731A; Canford SDV-HD; Draka 1.6/7.3AF; KLOTZ V16/72; RG11 Draka 1.4 / 6.6 AF Belden 1855A; CommScope 7538 Belden 1855ENH; Canford SDM, SDV-S-LFH; Cordial CVI 06-28, CVI 3-7; Draka 0.6/2.8 AF, 0.6L/2.8 AF; Extron BNC-5RC; Sommer 600-0101M, 600-0104M, KLOTZ V06/28, VMXx75Y Kansai 3C-5S Canare V(3-5)-3C Belden 1506A,;CommScope 2065V Canare V(3-5)-4CFB Belden 1505F Belden 8241; CAE KX6A; Canare LV-61S; Cordial CVI (CVM) 06-37; CommScope 5563; Draka 0.6/3.7, 0.6L/3.7 ; RG59B/U; Sommer 600-0051 (M,L,S), 600-0054 (M,L,S), KLOTZ V06/37 Belden 1505A, 8241F; Canare L-4CFB; CommScope 5565; Draka 0.8/3.7 AF, 755-801 (803, 804); Gepco VPM2000; Suhner S0426; Sommer 600-0451, 600-162(F) BBC PSF 1/3; Draka 0.6/3.7 Dz, 755-801 (803, 804); Suhner G04233D (PTT 6010) CAE VCB75; Helix 734 Belden 1695A; CommScope 2279V Canare V(3-5)-5C Hirschmann KOKA 712Cu Eupen 705 CRT 5V-HS Belden 1694A; CommScope 5765; Gepco VSD2001; Suhner S05163-02, 05133-07 Belden 1694A; CommScope 5765; Gepco VSD2001; Suhner S05163-02, 05133-07 Belden 1694F Canare V(3-5)-5CFB; Canford SDV-L, SDV-F Wisi MK 99A Canford SDV-F-HD; Draka 1.2L/4.8Dz, 1.2L/4.95AF CAE VCB 100 Belden 8281; Draka 0.8/4.9Dz Belden 8281F; Canare LV-77S Canare L-5CFB
Belden 1520A, 1521A, 1522A, 179DT; Draka 0.31/1.45 AF, 753-1304(2), 755-1302; Suhner G02233, ZNK CM14B Canare L-1.5C2VS; Suhner S02223; Kroschu (341 270, 341 280); RG 179 B/U; Sommer 600-025-03 (05) CAE MC75; Procom; Sommer 600-0701, 600-20-03 (05), 600-025-03 (05) Belden 1277R, 1278R, 1279R; Draka 0.41/1.9AF, 753-1104, 755-1103; Extron BNC-5 HR(P) (Bulk), BNC-5RC AT&T 735; CommTech RGBHV Belden 1406B, 1407B, 1417B CAE NC75.39; Draka 755-1001 (0.51/2.3Dz), 757-1001; Sommer 600-0751; VADN 7243 Belden 8218 Belden 1865A; CommScope 7536
Belden 1520A, 1521A, 1522A, 179DT; Draka 0.31/1.45 AF, 753-1304(2), 755-1302; Suhner G02233; ZNK CM14B Draka 0.41/1.9 AF, 753-1104, 755-1101; 755-1103; Extron BNC 5 HR(P) (Bulk) CAE MC75; Sommer 600-0701, 600-20-03 (05), 600-025-03 (05) Belden 1505A, 8241F; Canare L-4CFB; CommScope 5565; Draka 0.8/3.7 AF, 755-801 (803, 804); Gepco VPM2000; Suhner S04263; Sommer 600-0451 Draka 1.0/4.8AF, 755-901/5, Image 1000, KLOTZ V10/48
Chassis Connectors
88
True 75 Ω design meets the stringent HDTV / DVD requirements
Isolated or grounded versions
“D” shaped housing (provides flush mounting and protection of the
jacks from damage) or single feed through mountings
Gold plated center contact
Bulkhead Jacks
NBB75FI NBB75DFG NBB75DFGB NBB75SI
NBB75FI
NBB75DFG
Ordering Information
Nickel housing Black housing
Bulkhead jack, D-shape housing, feed through, groundet NBB75DFG NBB75DFGB Bulkhead jack, D-shape housing, feed through, isolated NBB75DFI NBB75DFIB Bulkhead jack, D-shape housing, solder version, grounded NBB75DSG NBB75DSGB Bulkhead jack, D-shape housing, solder version, isolated NBB75DSI NBB75DSIB Bulkhead jack, feed through, groundet NBB75FG Bulkhead jack, feed through, isolated NBB75FI Bulkhead jack, solder version, including isolationwashers NBB75SI
Look for the Logo
Technical Specifications
89
www.neutrik.com
Specifications
Rear Twist® & Rear Twist® Push Pull Bulkheads
Rear Twist Large Tiny & Cable & Cable Jack Jack Tiny Panel
Electrical
Mechanical
Cable anchoring Jacket crimping
Neutrik
®
chuck principle N / A
Cable O.D. range mm 4.0 - 7.7 2.5 - 3.8 4.0 - 8.0 N / A
- Rear Twist Large 10.3 - - - Center contact retention
>
30 N
-
Engagement force
<
25 N
<
20 N
Lifetime 1`000 mating cycles
Environmental
Temperature range -30°C to +85°C
-
30°C to +40°C
Solderability Complies with IEC 68-2-20
N / A
Contact crimpability Complies with IEC 60803
N / A
and IEC 60352-2
Materials
Shell: Brass (CuZn39Pb3), OPTALLOY coated
PA6 (Push Pull only) N / A N / A
N / A
D-Shape housing: Zinc diecast (ZnAl4Cu1)
N / A N / A N / A
gal Ni or black Cr plating Ground contact:
Bronze (CuSn6), 0.2 µm AuCo over 2 µm NiP15
-
Brass (CuZn39Pb3), OPTALLOY coated - - -
Center contact: Brass (CuZn35Pb2), 0.2 µm AuCo or
-
Brass (CuZn39Pb3), 0.2 µm AuCo - - -
Insulator: Teflon PTFE
Chuck: Polyacetal POM N / A N / A
N / A
Insulation Shell: Polyacetal POM N / A N / A N / A
Center Contact:
I.D. in mm Materials Plating Coding Ring (# of rings on base of contact)
0.4 Brass (CuZn39Pb3) 2 µm AuCo 0
0.5
5
0.6
1
0.7
2
0.9
3
1.1
6
1.2
4
1.7
0
Impedance 75
Rated voltage 500 V ac rms
250 V ac rms
Insulation resistance
>
5 G
Dielectric withstanding voltage 1500 V ac rms
750 V ac rms
VSWR / Return Loss ≤ 1.050 /
>
32 dB up to 1 GHz
1.10 / > 26 dB up to 1 GHz
1.03 / > 37 dB up to 1 GHz
1.065 / > 30 dB up to 2 GHz
1.14 / > 24 dB up to 2 GHz
1.05 / > 32 dB up to 2 GHz
1.100 / > 26 dB up to 3 GHz
1.22 / > 20 dB up to 3 GHz
1.08 / > 28 dB up to 3 GHz
Inner contact resistance 3 mΩ (initial)
Outer contact resistance 2 mΩ (initial)
to identify the original
Loading...