How it Works
Network Technologies
Loading...
RACKMUX-D17
Installation Manual
32 pgs1.75 Mb0

Network Technologies RACKMUX-V15, RACKMUX-D15, RACKMUX-V17, RACKMUX-V20, RACKMUX-D17 Installation Manual

Download
RACKMUX
®
Series
RACKMUX-V15/17/20
RACKMUX-D17
Rackmount Drawer with Keyboard, LCD
Monitor and Mouse
MAN047 Rev Date 5/9/2013
RACKMUX-V17-N (Front and Rear View)
TRADEMARK
RACKMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.
COPYRIGHT
Copyright © 2007, 2013 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the right to make changes in the product design without reservation and without notification to its users.
Typographic Conventions
The following table describes the typographic changes used in this instruc t ion.
Typeface
AAaaBBaaCCcc123 On-screen computer output
AAaaBBaaCCcc123
Meaning Example
C:>
What you type, contrasted with on-screen computer output; keyboard keys to press
C:> L
Press the Fn key
i
TABLE OF CONTENTS
Introduction......................................................................................................................................................................1
Features and Functions...................................................................................................................................................2
Installation .......................................................................................................................................................................3
Rack Mounting Instructions .........................................................................................................................................3
Optional Telco 2-Post Mounting ...............................................................................................................................4
Connect to a CPU........................................................................................................................................................4
Connect Extra Device..................................................................................................................................................6
Remote PC Connection...............................................................................................................................................6
Manual IP Address Change......................................................................................................................................8
Software IP Address Change ...................................................................................................................................9
Connect Power..........................................................................................................................................................10
Power Up...................................................................................................................................................................10
Display Functions..........................................................................................................................................................11
Standard Controls......................................................................................................................................................11
OSD Control Menu- 15 and 17 Inch VGA models (-V15/-V17).................................................................................11
OSD Main Menu .....................................................................................................................................................11
Brightness/Contrast Menu......................................................................................................................................12
Color Menu .............................................................................................................................................................12
Position Menu.........................................................................................................................................................12
Setup Menu.............................................................................................................................................................13
OSD Control Menu-DVI Model (-D17).......................................................................................................................13
OSD Main Menu .....................................................................................................................................................13
Brightness/Contrast Menu......................................................................................................................................14
Setup Menu.............................................................................................................................................................14
OSD Control Menu- 20 Inch VGA Model (-V20)........................................................................................................15
OSD Main Menu .....................................................................................................................................................15
OSD Control Menu- 17 Inch Hi-Resolution Model (-HR)...........................................................................................17
OSD Main Menu .....................................................................................................................................................17
Keyboard Functions ......................................................................................................................................................19
Function Key Operation..........................................................................................................................................19
Number Pad............................................................................................................................................................20
Other Uses of the Function Key..............................................................................................................................21
Numeric Keypad Option.............................................................................................................................................22
PS/2-USB Keyboard/Mouse Mode............................................................................................................................23
SAFETY.........................................................................................................................................................................24
Rackmux-KVM Drawer Standard Specifications...........................................................................................................25
General Specs...........................................................................................................................................................25
LCD – 15” ..................................................................................................................................................................25
LCD – 17” ..................................................................................................................................................................25
LCD – 20.1” ...............................................................................................................................................................26
Display Controller: VGA (-15,-17 & -20)....................................................................................................................26
Display Controller: DVI (-17)......................................................................................................................................26
OSD Control Board....................................................................................................................................................26
Keyboard....................................................................................................................................................................26
Touchpad...................................................................................................................................................................27
Troubleshooting.............................................................................................................................................................28
Index..............................................................................................................................................................................28
Warranty Information.....................................................................................................................................................28
ii
TABLE OF FIGURES
Figure 1- Mount RACKMUX to a standard rack.................................................................................................................................3
Figure 2- Position RACKMUX with clearance to open.......................................................................................................................3
Figure 3- Mount to Telco post with optional mounting brackets.........................................................................................................4
Figure 4- Connect a PS/2 CPU..........................................................................................................................................................4
Figure 5- Connect a USB CPU..........................................................................................................................................................5
Figure 6- Cables used for RACKMUX with DVI video support...........................................................................................................5
Figure 7- Connect a USB 1.1 device to the front (optional)................................................................................................................6
Figure 8- Connect Remote PC to KVM on IP at "LAN" port...............................................................................................................6
Figure 9- Remote Console Preview...................................................................................................................................................7
Figure 10- Login Screen for KVM on IP.............................................................................................................................................8
Figure 11- Network Configuration screen ..........................................................................................................................................8
Figure 12- Connect the power cord .................................................................................................................................................10
Figure 13- OSD Controls .................................................................................................................................................................11
Figure 14- Main Menu for 20-inch LCD Monitor...............................................................................................................................15
Figure 15- US(English) Keyboard Layout ........................................................................................................................................19
Figure 16- Keyboard LED Indications..............................................................................................................................................19
Figure 17- Keys of the Number Pad ................................................................................................................................................21
Figure 18- Additional multi-function keys.........................................................................................................................................21
Figure 19- U.S. (English) keyboard with numeric keypad................................................................................................................22
Figure 20- U.K. (English) keyboard with numeric keypad................................................................................................................22
Figure 21- German keyboard with numeric keypad .........................................................................................................................23
iii
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
INTRODUCTION
The RACKMUX-V15/17/20 Drawer (RACKMUX) consists of a Keyboard, Touchpad, and LCD monitor integrated into a 1RU rack-mountable drawer with wrist pads. When access to a server rack is needed, the drawer can be pulled out and the display lifted up like a notebook computer, revealing the keyboard and mouse. When the drawer is not in use, the display can be folded forward and down so the 1RU drawer can be pushed into the cabinet easily and smoothly, helping to organize and streamline busy server rooms. The NTI RACKMUX product line offers a range of KVM Drawer solutions ideal for rack and server management applications, which will ensure reliability and serviceabi lity.
The RACKMUX will switch between USB and PS/2 standar ds for versatile connection to a CPU. The forward-folding LCD monitor is offered in either 15”, 17”, or 20” (designate d in the product name as -15 ,-17 o r -20) and the video format can be either VGA or single-link DVI (designated by –V or –D: example RACKMUX-V15). For user input, the drawer offers a notebook-style keyboard, wrist-pad, and a three-button touchpad. The keyboar d and mouse can be connected using U SB and PS/2 cables. USB and PS/2 interfaces will remain active at all times and the keyboard and mouse can be switched, at any time, to use either one. The RACKMUX-V15/-V17/-V20 also provides a front panel USB 1.1 p ort for the connection of a n external USB device (such as a flash drive).
The keyboard and mouse interface is compatible with Windows platform CPUs. This multiple interface capability reduces equipment costs by ensuring that a single console is compatible with various PC/server input devices.
Installing the RACKMUX into any server environment will offer:
• A space saving 1RU design, easily mountable in any 19” cabinet/rack
• A forward-folding 15”,17”, or 20” TFT LCD with built-in OSD menu for screen adjustments
• Auto shut-OFF switch: Turns OFF the power to the monitor when the LCD is in a folded-closed position.
• Built-in 83-key (US) or 84-key (Europe) keyboard with wrist pad
• Standard 3-button mouse touchpad
• Support for PS2 and USB con nections for the keyboard and mouse.
• Support for VGA (15”, 17”or 20” model) or single-link DVI signals (17” model only)
• Front-access USB port for easy accessory USB 1.1 device connection
• An internal cab le arm for proper cable management when sliding the drawer open and closed
• Added security with a drawer lock to prevent unwanted access
• Locking rails to prevent movement of the drawer when fully extended
• Built-in univ ersal (100-240VAC) low power consumption power supply
• Multi-languag e support including: US(English), UK(English), German, French, Italian, Spanish
Materials Included with this kit:
9 NTI RACKMUX-V15/17/20 Drawer with VGA Video support
~or~
9 NTI RACKMUX-D17 Drawer with DVI Video support 9 2 Keys for Lock 9 2 Rear Mounting Brackets w/nuts 9 8 #10-32x3/4” screws and cage nuts for mounting to a rack 9 IEC Power Cord- country specific 9 CD with a pdf file of this owner's manual and the drawer installation manual 9 USB-AB-2M 2 meter USB Type A male-to-USB Type B male cable 9 VVKINT-6-MM 6 foot PS/2 mouse and keyboard cable (not included with KVM on IP model) 9 VEXT-THN-6-MM 6 foot VGA video cable (models with VGA Video support only) 9 DVI-DS-2M-MM 2 meter DVI video cable (model with DVI Video support only) 9 5 foot RJ45-to-RJ45 CAT5 patch cable (model with KVM on IP only)
9 CAT5-CO-MF Crossover Adapter (model with KVM on IP only)
Alternative Cables (not supplied): (available in 3,6,10 and 15 foot lengths) VKMEXT-xx-MM for VGA Monitor and PS2 Keyboard and Mouse input
USBVEXT-xx-MM for VGA Monitor and USB Keyboard/Mouse input and USB device support
where: xx is the length of the cable in feet MM indicates male-to-male connector
Option:
• Trackball option- for a RACKMUX with a trackball instead of a touchpad- add “T” to the part number (i.e. RACKMUX-V17-T)
• Numeric keypad option- for a separate 17-key numeric keypad, add “-N” to the part number (i.e. RACKMUX-V17-N)
• KVM on IP option- for a RACKMUX with a KVM on IP unit for remote access, add “-IP” to the part number
(i.e. RACKMUX-V17-N-IP)
• Hi-Resolution Monitor- for a 17” RACKMUX with hi-resolution mon itor (1920 x 1200)- add “HR” to the part number (i.e.
RACKMUX-V17HR (available on 17” models only))
Cables can be purchased from Network Technologies Inc by calling
(800) 742-8324 (800-RGB-TECH) in the US and Canada or (330) 562­7070 (worldwide).
1
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
18
Front View RACKMUX-V17
15
21A 21B
13
16
14
17
- or -
(RACKMUX-D17)(RACKMUX-V17)
19
1
2 3
4 5 6
1
7
A
22
9
24
8
2320
Fn
10
Rear View RACKMUX-V17
PS/2
11 12
FEATURES AND FUNCTIONS
1. Power Button- press to turn the LCD monitor ON and OFF
2. Power LED- Indicates operation status
Green = Power-ON, Video Input Signal OK Red = Suspend / Stand-by, or no Video Input Signal
3. Menu Button- press to turn ON the OSD menu
4. Up Arrow Button- press to move the cursor in the OSD menu up
5. Down Arrow Button- press to move the cursor in the OSD menu down
6. Select Button- press to select a menu item (when OSD menu is ON) or press to auto adjust the video quality (when OSD
menu is OFF)
7. NumLock LED- illuminates when the number lock is ON
8. CapsLock LED- illuminates when CapsLock is ON.
9. Scroll Lock LED- illuminates when the Scroll Lock keyboard feature is ON.
10. Fn LED- illuminates when Function Featur es (page 19) are enabled.
11. USB LED- illuminates when RACKMUX drawer is in USB mode
12. PS/2 LED- illuminates when RACKMUX drawer is in PS/2 mode
13. 3-button mouse- for controlling mouse movements on the monitor and controlling the computer
14. Keylock- to prevent unauthorized use of the RACKMUX
15. Auto Shut-OFF- switch automatically shuts OF F the LCD display when the monitor is folded down
16. keyboard- for manual data e ntry and computer control
17. USB Port- USB Type A female- for connection of any USB 1.1 compatible device (such as a flashdrive, printer, etc)
18. LCD Display- for vie wing the video signal from the connected CPU
19. IEC Connector- for attachment of the IEC power cord to power the RACKMUX drawer
20. Switch- for powering ON and OFF the RACKMUX drawer
21. Video In- 21A. 15HD Female- for connection of the VGA video cable from the CPU (onl y in models that support VGA video)
21B. DVI-D Female- for connection of a DVI-D video cable from the CPU (only in models that support DVI)
22. USB- USB T
23. Keyboard Connector- purple 6 pin miniDIN female- for connection of the PS/2 keybo ard cab le from a PS/2 CPU
24. Mouse Connector- green 6 pin miniDIN female- for connection of the PS/2 mouse cable from a PS/2 CPU
ype B female- for connection of the USB cable from a USB CPU
2
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
s
INSTALLATION
The following rack mounting instruction does not apply to RACKMUX units with 20 inch LCD monitors. For mounting instruction applicable to models with 20 inch LCD monitors, see “Installation Manual For Drawer with 20 Inch LCD Monitor” on the CD.
Rack Mounting Instructions
The RACKMUX was designed to be mounted to a rack and includes mounting flanges to make attachment easy.
1. Determine the mounting height in the rack for the drawer. It should be a height comfortable to use the keyboard and see the LCD display. Mark holes in each of the 4 corner cabinet rails at points all level with each other.
2. Secure the rear brackets to the rear rack cabinet rails. Apply the top screws (supplied) for each bracket to the holes marked in step 1.
3. Lift the keyboard into position and line the studs on the left and right sides up with the slotted openings in the rear bracket. Apply the nuts (supplied) to the studs but do not tighten the nuts yet.
FYI: There are 4 mounting studs provided on each side of the RACKMUX. Depending on the depth of the rack and distance apart of the cabinet rails, the position of the rear bracket may make all 4 studs available for use. In this case, apply the 2 nuts to the studs furthest apart from each other on each side.
4. Slide the drawer in until the top holes in the front bracket flanges line up with the holes marked in step 1. Secure the front
brackets on the drawer to the front cabinet rails with two screws per bracket. Be sure to tighten the screws securely. Then tighten the nuts applied in step 3.
5. Apply one more screw to each of the rear brackets to finish.
Front brac ke t
flange on dra we r
Secure bracket to rail using two
screws and nuts (supplied)
Front Cabine t Rail
Drawer
Stud on dra we r
Rear bracket overlapping drawer
(Rear edge of dra w er)
Apply nuts (suppli ed) t o studs and secure rear brackets to drawer.
Re ar Ca binet Rail
Rear bracket flange
Secure bracket to rail using two
screws and nut (supplied)
Figure 1- Mount RACKMUX to a standard rack
Note: To provide sufficient room for the LCD monitor to be opened to a p ro per viewing angle (a minimum 90 degree position from the keyboard), ensure that all devices mounted above the RACKMUX extend no more than 1.75” from the rack frame. (See Fig. 2)
Figure 2- Position RACKMUX with clearance to open
"X" must be less than 1.75" for LCD to open to full 90
90
Side View of RACKMUX
3
Server mounted
X
above RACKMUX in the same rack
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Optional Telco 2-Post Mounting
If the Telco 2-post mounting bracket kit (NTI# RL-T15-TEL) is to be used, secure the short and long br ackets to each side of the drawer as shown in Fig. 2. Apply 2 nuts (supplied) per bracket to secure the brackets to the drawer. Apply two #10-32x3/4” screws (supplied) per bracket to the post at the desired height. Slots are provided in the brackets to make minor depth adjustments easy. Be sure to properly tighten all nuts and screws before using the drawer.
Figure 3- Mount to Telco post with optional mounting brackets
Connect to a CPU
The RACKMUX may be connected to either a PS/2 or a USB CPU with a VGA video port. To connect to a PS/2 CPU, use a VEXT-6-MM cable and VVKINT-6-MM cable as shown in Figure 4. To connect to a USB CPU, use the VEXT-6-MM and USB­AB-2M cables as shown in Figure 5.
Figure 4- Connect a PS/2 CPU
4
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Figure 5- Connect a USB CPU
When connecting a CPU with DVI support to the single-link DVI port of the RACKMUX, use a DVI-DS-2M-MM (supplied) for the DVI video signal, a USB-AB-2M (supplied) for the USB connection, and if using PS/2 keyboard and mouse connections, connect a VVKINT-6-MM cable (supplied) between the CPU and RACKMUX.
DVI-D-Male
USB Type A Male
6 miniDIN Male
6 miniDIN-Male
Purple-Keyboard
6 miniDIN-Male
Green-Mouse
DVI-D-Male
USB-A - Male
(.5, 1, 3, and 5 meter cables also availab le)
DVI-DS-2M-MM
(supplied)
USB-AB-2M (supplied)
VVKINT-6-MM (supplied)
(3,10, 15,25, 3 5, and 50 foot lengths a lso available)
DVI-D-Male
USB-B - Male
6 miniDIN-Male
Purple-Keyboard
6 miniDIN-Male
Green-Mouse
USB Type B
Male
Figure 6- Cables used for RACKMUX with DVI video support
5
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Connect Extra Device
On the front of the RACKMUX is an additional USB Type A port to be used, if desired, for an extra accessory. Any low or full speed USB device may be connected to this port to be used. This port is fully compliant with USB standard 1.1.
Note: In order for the optional USB device port to be usable, the USB port on the rear of the RACKMUX must be connected to a USB enabled CPU (a 2 meter USB cable is supplied).
Note: If a USB keyboard or mouse is connected, operation of the RACKMUX keyboard or mouse may cause unpredictable results. Do not try to use both mice or both keyboards at the same time.
Connect optional USB 1.1 or 2.0 device
PRINTER
CAMERA
FRONT VIEW OF RACKMUX-V17
SCANNER
FLASH DRIVE
Figure 7- Connect a USB 1.1 device to the front (optional)
Note: If a USB 2.0 device is connected to the optional USB device port, it will operate at USB 1.1 speed.
Remote PC Connection
The RACKMUX with KVM on IP unit includes a port for Ethernet connection to your LAN. If you have purchased the RACKMUX with KVM on IP (i.e. RACKMUX-V17-N-IP), follow these instructions to make your connections for remote access.
1. Make a connection between an available RJ45 Ethernet port on a PC and the ”LAN” port on the RACKMUX. A five foot patch cable and crossover adapter have been included for this purpose.
Figure 8- Connect Remote PC to KVM on IP at "LAN" port
6
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
2. The default IP address of the KVM on IP is 192.168.0.70. If 192.168.70 is not compatible with your subnet, you may want to change the IP address of the KVM on IP to one that is. To
change the IP address of the KVM on IP, either follow the “Manual IP Address Change” or the “Software IP Address Change” methods described on page 8 and page 9 .
3. Enter the IP address in the browser URL address block. .
4. Log into the KVM on IP. Enter the default user name and password for the KVM on IP:
Username = super Password = pass
5. With a proper login, a window “Remote Console Preview” will be displayed. Click on the link “Click to open”.
Figure 9- Remote Console Preview
A connection will be made between your remote PC and the RACKMUX Drawer. The screen that opens is a virtual PC that enables you to control the RACKMUX just as if you were actually at the keyboard of the RACKMUX. Using the mouse, switch between the virtual PC and your actual computer interface.
If the remote connection is closed while in the KVM on IP menu, to re-open the connection click on “Remote Control”, then “KVM Console”.
Note: There are more features available in the menu for the KVM on IP, but their use or configuratio n is not necessary in the operation of the RACKMUX-V17-N-IP.
7
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Manual IP Address Change
1. The Ethernet port on the PC must be configured with an IP of 192.168.0.xxx where xxx is any number except 70.
(You may need to configure the Ethernet port network information on the PC such that it can connect to the KVM on IP device in the RACKMUX.)
Note: Connecting to the KVM on IP requires the installation of the Java Runtime Environment. A link to the web page from which it can be downloaded and installed is provided on the Product Manual CD in addition to a Windows compatible copy of the application itself.
2. Open a browser window on the PC. Type “192.168.0.70” into the URL address block. A login prompt will appear.
Figure 10- Login Screen for KVM on IP
3. Enter the default user name and password for the KVM on IP:
Username = super Password = pass
4. The KVM on IP will open the main menu. To change the network configuration, go to “Device Settings”, and then “Network” to open the network configuration settings page for the KVM on IP.
Figure 11- Network Configuration screen
8
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
5. Enter the desired network connection settings (IP address, subnet mask, gateway) as compatible with your network.
Make note of these settings in case you need them later.
6. With the settings updated, press “Apply” to implement the changes in the KVM on IP. Your browser connection to the KVM on IP is no longer valid.
7. To restore connection to the KVM on IP, change the IP address on the PC back to an address compatible with your network and now also compatible with the KVM on IP.
Having configured the KVM on IP to be compatible with your network, you can now make a direct cable connection (crossover adapter not needed) to your network through a router or switch.
Software IP Address Change
1. Locate the program psetup.exe on the CD this manual is found on, in the “KVMonIP” subdirectory. Double-click on it.
2. Click Refresh Devices. The program will detect any network connected IP-KVM devices and display them by their MAC addresses.
3. Click Query Device to find the current IP configuration of the selected MAC address device.
4. Set IP auto configuration as “None”; and enter the new IP address and Subnet mask.
5. Enter
6. Click Setup Device. If the “super” login was authenticated, it’ll show “Successfully configured device”. Otherwise it will show
“Permission Denied”.
7. With a successful IP address change, login to the KVM on IP using your browser.
super and pass as the login and password.
9
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Connect Power
Connect the IEC power cord to the power port as shown below.
Figure 12- Connect the power cord
Power Up
Power up the RACKMUX and connected computer in this order.
1. Power On the RACKMUX
2. Power ON the attached CPU. If a device is plugged into the USB port on the front of the RACKMUX, it can powered-ON at any time.
Note: During power-up, do not attempt to type or otherwise use the keyboard. Doing so may result in boot errors and loss of keyboard and mouse.
10
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
DISPLAY FUNCTIONS
An NTI RACKMUX with a 20” monitor supports resolutions up to UXGA (1600x1200), 17” monitor supports resolutions up to SXGA (1280 x 1024), and a 15” monitor supports resolutions up to XGA (1024 x 768), each with a refresh rate at between 55 and 76Hz. The quality of the image on the LCD monitor is adjustable using an On Screen Display (OSD) menu using the control buttons on the RACKMUX.
Standard Controls
The RACKMUX has 5 standard control buttons and a power LED. The 5 standard control buttons o perate as follows:
• The Power button turns the R ACKMUX LCD and backlight ON and OFF as desired.
• The Power LED located immediately below the Power button is a dual color
LED. It will illuminate with a green color when the RACKMUX is powered ON and working properly. It will illuminate with a red color if the RACKMUX is powered ON but there is no input signal detected.
• The Menu button is used to bring up the OSD menu where the various
settings of the LCD display can be adjusted. Once the OSD screen is displayed, the Menu button is used to make selections within the menus. See "OSD Control Menu" (below) for more on LCD display settings.
• The Up and Down Arrow buttons are used to navigate through the menus.
Move the cursor up or down as desired to highlight an item for selection.
Once an item is highlighted, pressing the Menu button will select it.
Power ON/OFF
Power LED
Menu
Up Arrow
Down Arrow
Select/ Auto Adjust
Controls for the OSD Menus
Figure 13- OSD Controls
• The Select button is used to make selections within the OSD menus when the OSD menu is ON. When the OSD menu is
OFF, the Select button will act as an Auto Adjust button to keep the user from having to use the menus to adjust the quality of the image on the monitor.
OSD Control Menu- 15 and 17 Inch VGA models (-V15/-V17)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the OSD Menu, press the Menu button (above). To turn the Menu back OFF, either select "EXIT" from the main menu or just wait 10-60 seconds and it will automatically be cleared from the screen.
OSD Main Menu
Selection Purpose Range
Brightness/Contrast Increase/decrease panel brightness/contrast level 1-100 Color R,G,B color temperature control 1-100 Position
Setup
Exit Exit from the OSD control menu
• Video Image horizo ntal and vertical position control
• Clock setting
• Phase control
• Control OSD Image positio n on screen
• Set time OSD will stay on screen before auto shutoff
• Select the language of the OSD menu
1-100
-­10 to 60 seconds Several languages (see page 8)
11
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Brightness/Contrast Menu
Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and contrast levels of the LCD display. Using the Up or Down Arrows to navigate the menu, highlight either the BRIGHTNESS or CONTRAST sections and press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting. Select EXIT when finished to return to the Main Menu.
Color Menu
Selecting the Color menu will bring up a screen in which the user can adjust the Red, Green, and Blue color levels (values from 1-
100) of the LCD display. With the RED, GREEN, or BLUE sections highlighted, (use the Up or Down Arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting. Select EXIT when finished to return to the Main Menu.
Position Menu
Selecting the Position menu will bring up a screen in which the user can select AUTO ADJUST to automatically adjust the horizontal and vertical position of the displayed image on the monitor, as well as adjust the clock and phase settings if they are not correct. The user can also individually adjust these settings if so desired. With any of the sections highlighted, (use the Up or
Down Arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main Menu.
12
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Setup Menu
Selecting the Setup menu will bring up a screen in which the user can adjust
OSD POSITION-the position of the OSD menus on the LCD display OSD TIME-the length of time the user can be idle before the OSD menu automatically exits (adjustable from 10
to 60 seconds)
LANGUAGE-the language th at the OSD menus will be presented in With the item highlighted, (use the Up or Down arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main Menu.
OSD Image can be moved to different points on the display
OSD Control Menu-DVI Model (-D17)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the OSD Menu, press the Menu button (page 11). To turn the Menu back OFF, either select "EXIT" from the main menu or just wait 10-60 seconds and it will automatically be cleared from the screen. Any changes made before exiting the menu will be saved.
OSD Main Menu
Note: In order to display the OSD Menu, the RACKMUX must first be connected to a video source (see “Connect to a CPU” – page 4).
Note: If menu does not appear when the Menu button is pressed, the monitor may be set fo r a “PC” (VGA) input source. Press the Up Arrow button on the monitor to switch it to a “Digital” (DVI) input source.
13
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Selection Purpose Range
Brightness/Contrast Increase/decrease panel brightness/contrast level 1-100 Setup
Exit Exit from the OSD control menu
• Control OSD Image positio n on screen
• Set time OSD will stay on screen before auto shutoff
• Select the language of the OSD menu
• Select Input Source to display
• 0-4
• 10 to 60 seconds
• English, Spanish, German, Italian, or French
• Digita l or PC (must
be set to Digital)
Brightness/Contrast Menu
Selecting the Brightness/Contrast menu will bring up a screen in which the user can adjust the brightness and contrast levels of the LCD display. Using the Up or Down arrows to navigate the menu, highlight either the BRIGHTNESS or CONTRAST sections and press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting. Select EXIT when finished to return to the Main Menu.
Setup Menu
Selecting the Setup menu will bring up a screen in which the user can adjust
OSD POSITION-the position of the OSD menus on the LCD display (positions 0-4)
OSD TIME-the length of time the user can be idle before the OSD menu automatically exits (adjustable from 10
to 60 seconds)
LANGUAGE-the language th at the OSD menus will be presented in
INPUT SOURCE- the type of signal that is coming from the CPU, either Digital (DVI) or PC (VGA)
NOTE: As used on this RACKMUX, the INPUT SOURCE must be set
With the item highlighted, (use the Up or Down Arrow to move between them), press the Select button to choose the option to adjust. Then use the Up or Down Arrow to adjust the setting as needed. Select EXIT when finished to return to the Main Menu.
OSD Image can be moved to different points on the display
to “Digital”.
14
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Control Menu- 20 Inch VGA Model (-V20)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the OSD Menu, press the Menu button (page 11). To turn the Menu back OFF, either press the Menu button again or just wait approximately 15 seconds and it will automatically be cleared from the screen. Any changes made before exiting the menu will be saved.
OSD Main Menu
The Main Menu is broken into three sections, Picture, Setup, and Screen. Press one of the arrow buttons to move between them. To select a menu and move to characteristics within them (i.e. CSM, Brightness, or Contrast under the Picture menu), press the Select button while the desired menu is displayed.
Figure 14- Main Menu for 20-inch LCD Monitor
Note: In order to display the OSD Menu, the RACKMUX must first be connected to a video source (see “Connect to a CPU” – page 4).
15
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Within each menu are characteristics of the monitor that can be adjusted. While a characteristic is selected, press the Select button to open the adjustment screen. Use the Up and Down Arrow buttons to make adjustments as desired. Press Select again to return to the characteristic selections.
Characteristics that can be adjusted are described in the chart below.
Selection Purpose Range Picture
CSM Brightness Contrast
Setup
Language Transparency Set ID Volume Factory reset
Screen
Auto Configure H Position V Position Clock Phase
Press the Menu button to exit the OSD menu.
• Set panel color temperature
• Increase/decrease panel brightness level
• Increase/decrease panel contrast level
• Select the language of the OSD menu
• Adjusts how boldly the menu is displayed
• Not Applicable to this product
• Reset the monitor to factory settings
• Auto adjust settings in this cat egory
• Control Horiz ontal OSD Image position on screen
• Control Vertical OSD Image p osition on screen
• 5800K,9300K,6500K,User
• 0-100
• 0-100
• English, Spanish, German, Italian, or French
• 0-100
• 0-99 or Off
•
• On/Off
• On/Off
• 0-100
• 0-100
• 0-100
• 0-100
16
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Control Menu- 17 Inch Hi-Resolution Model (-HR)
The OSD (On Screen Display) Menu enables the user to select the desired characteristics of the LCD display. To activate the OSD Menu, press the Menu button (below). To turn the Menu back OFF, either press the Exit button or just wait approximately 10 seconds (timing is adjustable) and it will automatically be cleared from the screen. Any changes made before exiting the menu will be saved.
OSD Main Menu
The Main Menu is broken into five sections, Color, Picture, Function, OSD Menu, and Misc. Press one of the arrow buttons to move between them. The Picture and Function sections only apply when the RACKMUX is connected as VGA instead of DVI. To select a menu and move to characteristics within them (i.e. CSM, Brightness, or Contrast under the Picture menu), press the Select button while the desired menu is displayed.
Characteristics that can be adjusted are described in the chart below.
Selection Purpose Range Colour
Contrast Brightness Colour Temp. Colour Adjust
Picture (VGA Only)
H Position V Position Phase Clock Sharpness
Function (Fx) (VGA Only)
• Increase/decrease panel contrast level
• Increase/decrease panel brightness level
• Set panel color temperature
• Select RGB balanc e (goes to submenu)
• Control Horiz ontal position of screen
• Control Vertical positi on of screen
To manually force auto adjust of monitor settings Select Auto Adjust or Auto Color functions
• 0-100
• 0-100
• 5800K,9300K,6500K,User
• 0-100
• 0-100
• 0-100
• 0-100
• 0-100
• 1-5
17
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
OSD Menu
Language OSD H. Pos. OSD V. Pos. OSD Timer Translucent
• Select the language of the OSD menu
• Control Horiz ontal OSD Image position on screen
• Control Vertical OSD Image p osition on screen
• Control if OSD will time out
• Adjusts how boldly the menu is displayed
Misc.
• Select Input
• Reset monitor to default settings
Press the Exit button or select “Exit” to exit the OSD menu.
• English, Spanish, German, Italian, or French
• 0-100
• 0-100
• On/Off If On, select 3-100 seconds.
• -/+
• VGA or DVI
• Yes/No
Colour Adjust submenu
Input submenu
18
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
KEYBOARD FUNCTIONS
The keyboard on the RACKMUX-Vxx is a standard condensed Windows format. To reduce the keyboard size, some keys have been assigned multiple functions, accessible via the "Fn" key. This section will describe which keys have multiple functions and how to enable them. Use the LEDs to know what special features are enabled.
Function Key Operation
The Function (“Fn”) key provides several special functions on the RACKMUX keyboard, including:
enabling otherwise standard keyboard keys to be used as the keys of a numeric keypad
enabling multi-function keys to change operation
enabli ng the “T” key to act as a mode key to toggle between USB and PS/2 keyboard/mouse mode
To turn ON (lock) the Function key, press the “Fn” key twice quickly (double-click). The “Fn” LED will illuminate. To turn OFF (unlock) the Function key, press the “Fn” key twice quickly again. The “Fn” LED will turn OFF.
Note: The "Fn" key will also operate similar to the shift key (with only momentary effect). Press and hold the "Fn" key prior to pressing the special function key. The "Fn" key will remain active as long as it is depressed.
Esc
~ `
F2
F1
!
1
F3
F4
@
#
2
$
3
4
F6
F5
%
5
F7
F8
F9
&
^
7
6
*
8
789
F10
(
9
F11 F12
)
0
Tab
WE R
Q
CapsLock
ASDF GHJK L
Shift
ZXCVB
T
YU I OP
123
M
N
654
<
,
Ctrl
Fn
Alt
Alt
Function Key to enable additional key functions
Num Lk
Insert Delete Prt Sc
+ =
}
{
]
[
Enter
:
"
;
'
+
*
>
.
?
Shift
/
.
/0
Ctrl
Home
Sys Rq
Backspace
Pg Up
Enter
Pause BreakScr Lk
\
EndPg Dn
1
On= NumLock is locked
Figure 16- Keyboard LED Indications
Figure 15- US(English) Keyboard Layout
On= Function On= CapsLock is locked
A
On= Scroll Lock is locked
Key feature
is ON
Fn
On= USB Keyboard/Mouse mode
19
On= PS/2 Keyboard/Mouse mode
PS/2
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Number Pad
The functionality of a Number Pad on a standard Windows keyboard has been incorporated into the keyboard of the RACKMUX-V15 (see Figure 17, page 21 ).
To substitute the keys of the Number Pad:
1. Press the "NumLock" key. The NumLock LED ( ) will illuminate.
2. Press the "Fn" key twice quickly (double-click). The "Fn" LED will illuminate. To turn OFF Number Pad functions:
1. Press the "Fn" key twice quickly (double-click). The "Fn" LED will turn OFF.
2. Press the "NumLock" key. The NumLock LED ( ) will turn OFF.
With the Fn and NumLock LEDs illuminated, pressing some standard keys will result in displaying characters as indicated in the chart below.
Standard Key Displayed when NumLock is
j k l u j o 7 8 9 m
.
(period)
/
(forward slash)
;
(semicolon)
’
(apostrophe)
-
(hyphen)
[
(left bracket)
ON
1 2 3 4 5 6 7 8 9 0 .
(period)
1
1
Function when NumLock is
OFF
End
Down Arrow
Page Down
Left Arrow
---
Right Arrow
Home
Up Arrow
Page Up
Insert
Delete
/
(forward slash)
+
(plus sign)
*
(asterisk)
-
(minus sign)
ENTER
20
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
&
7
789
*
8
(
9
Num Lk Scr Lk
UIO
654
{ [
Enter
JKL
123
: ;
+
" '
*
M
>
.
.
? /
/0
Figure 17- Keys of the Number Pad
Other Uses of the Function Key
The Function ("Fn") key (page19) will enable other standard keyboard features in addition to the Number Pad keys (page 20) .
Key Function when Fn key is not locked ("Fn" LED is OFF)
Numlck (Number lock) Scr Lck (Scroll Lock)
Insert Prt Sc (Print Screen) Delete Sys Rq (System Requirements) Pause Break
Up Arrow Page Up
Down Arrow Page Down
Left Arrow Home
Right Arrow End
Num Lk Scr Lk
Insert Delete Prt Sc
Sys Rq
Pause Break
Key Function when Fn key is
Locked ("Fn" LED is ON)
Pg Up
Home
EndPg Dn
Note: The "Fn" key will also operate similar to the shift key (with only momentary effect).
Figure 18- Additional multi-function keys
21
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Numeric Keypad Option
Models with the Numeric Keypad option (-N) (i.e. RACKMUX-V15-N) have a standard Windows keyboard with 17-key numeric keypad.
When the Numeric Keypad option is present, the Function (“Fn”) key, (page 19) is only used to toggle between PS/2 and USB keyboard/mouse mode (page 23).
Note: When the Numeric Keypad option is present, the "Fn" key does not lock. Instead, the “Fn” key operates similar to the shift key (with only momentary effect).
F1
Esc
!
~
1
`
Tab
Q
Caps Lock
Shift
Fn
Ctrl
Function Key
F2
F3
F4
@
#
2
3
WE R
$
4
F6
F5
%
5
F7
F8
F9
F10
&
^
7
6
T
YU I OP
(
*
9
8
F11 F12
)
0
ASDFGHJK L
<
ZXCVB
Alt
M
N
,
Alt
: ;
>
.
PrtSc SysRq
{ [
? /
Insert
Scroll
Pause
Delete
Break
Lock
+
Backspace
=
} ]
"
Enter
'
Shift
Home
Page
\
Up
Page Down
End
Num Lock
/
789
Home P g Up
456
123
End
0
Ins
*
PgDn
.
Del
-
+
Enter
Figure 19- U.S. (English) keyboard with numeric keypad
Esc
`
Tab
Caps Lock
Fn
Shift
F2
F1
!
1
Q
F3
F4
"
2
$
3
4
WE R
F6
F5
%
5
F7
F8
F9
&
^
7
6
T
YU I OP
*
8
ASDFGH JKL
ZXCVB
Ctrl
Alt
\
M
N
AltGr
F10
(
9
F11 F12
)
0
<
,
PrtSc
SysRq
{ [
:
@
;
'
?
>
.
/
Insert
Figure 20- U.K. (English) keyboard with numeric keypad
Pause
Scroll Lock
+
Backspace
=
} ]
Break
Delete
Home
~
Page Up
#
Num Lock
/
*
789
Home
PgUp
-
+
Enter
Shift
Page Down
End
456
123
End
0
Ins
PgDn
.
Del
Enter
22
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Esc
^
F2
F1
"
!
2
1
Tab
@
Q
ASDF GHJK L
F3
2
3
3
F4
$
4
F5 F6 F7
WE R
F8
F9 F10
(
%
5
T
/
&
7 {
6
8 [
ZU I OP
)
9 ]
F11 F12
=
0 }
Druck
S-Abf
? \
U
O
A
Rollen
* + ~
Pause
Untbr
Entf
Pos1
Bild
' #
Bild
Num
789
Pos1
456
/
YXCVB
N
Strg
Fn
>
Alt
<
;
M
u
AltGr
.
Einfg
:
,
Ende
123
Ende
0
Figure 21- German keyboard with numeric keypad
PS/2-USB Keyboard/Mouse Mode
The RACKMUX keyboard and mouse can be configured to connect to either a PS/2 or USB enabled CPU. At initial power ON from the factory, the keyboard will be in PS/2 mode.
To toggle keyboard mouse mode when standard condensed keyboard is present
1. Press the "Fn" key twice quickly (double-click). The "Fn" LED will illuminate.
2. To toggle the keyboard to USB mode, depress and hold the “T” key for at least 7 seconds. The “USB” LED will illuminate. Release the “T” key.
3. To toggle the keyboard back to PS/2 mode, press and hold the “T” key again for at least 7 seconds. The “PS/2” LED will illuminate. (See Figure
To toggle keyboard mouse mode when Numeric Keypad is present
1. To toggle the keyboard to USB mode, depress and hold the “Fn“ key (“Fn” LED will illuminate) and the “T” key for at
least 7 seconds. The “USB” LED will illuminate. Release both keys.
2. To toggle the keyboard back to PS/2 mode, press and hold the “Fn” and “T” keys again for at least 7 seconds. The
“PS/2” LED will illuminate. (See Figure 16 on page 13.) Release both keys.
Note: In the event of a power failure, the RACKMUX will power up the keyboard in the mode it was last configured for.
16 on page 13.) Release the “T” key.
Bild
Bild
-
*
+
Enter
.
Entf Einfg
23
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
SAFETY
This NTI product has been designed and fully tested with user safety of the utmost importance. As with all electronic devices, this NTI product should be handled and operated with care. In order to avoid possible injury and to reduce any risk of damage to this product, please read and follow each of these safety instructions.
• Follow all i nstructions fou nd in this manual.
• Follow all instructions found on the product.
• Do not attempt to perform any service on this product unless specifically instructed to in this manual.
• Objects that can damage or be spill ed on this product should be kept away from this product. Liquids, if spilled, could come
into contact with voltage points causing a risk of fire or electrical shock.
• Always unplug this product before cleaning it. Do not use any liquid or aerosol cleaners to clean it.
• Do not install or use this product near water
• Be sure to mount this product on a sol id, stable surface or in a rack (if applicable)
• Route all cables and the power cord away from sharp edges or objects that could cause damage to them
• Use only the power cord or AC adapter that came with this unit or one that meets the requirements specified in this manual
• Use only a properly grounded 3-wire electrical outlet for power connection
• Unplug this product and contact NTI should any of the following conditions occur:
• The power cord or connection cables have been damaged
• The product has come into contact with any liquids
• The product does not operate properly despite having followed all of the instructions
• The product has been dropped or the case has been damaged in any way
• The product performs distinctly different than it did when first put into service
24
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
RACKMUX-KVM DRAWER STANDARD SPECIFICATIONS
General Specs
Case Material.................................................Electro-galvanized steel black powdercoated
Dimensions WxDxH (in.)...............................19 x 21.9 x 1.75
Supported Rack Depths………………………..Adjustable 22” – 39” Weight……………………………………………26 lbs.
Input Power....................................................AC 100-240V, 50 – 60 Hz
Operating Temperature..................................0-40˚C
Storage Temperature…………………………..-20-60˚C Relative Humidity……………………………….. 20-90%, non-condensing
Approvals.......................................................All parts comply with RoHS
LCD – 15”
Display area…………………………………….304.1mm (W) x 228.1 (H) (15 inch diagonal) Panel Type………………………………………TFT Active
Number of Pixels ...........................................1024 (H) x 768 (V)
Number of Colors...........................................16.2 Million
Pixel Pitch......................................................0.297(H) x 0.297(V)
Color Pixel Arrangement.................................RGB Vertical Stripe
Brightness......................................................250cd/m^2 (Nits)
Response Time..............................................16ms
Viewing Angle................................................Horizontal: 140º; Vertical: 125º (Typ.)
Optimum Viewing Direction............................6 o’clock
Backlight Unit……………………………………2x CCFLs (Top & Bottom, edge-light)
Operating Lamp Life ......................................30,000 – 40,000 hrs
Contrast Ratio…………………………………..500:1
LCD – 17”
Display area…………………………………….337.92mm (W) x 270.336 (H) (17 inch diagonal) Panel Type………………………………………TFT Active
Number of Pixels ...........................................1280 (H) x 1024 (V)
Number of Colors...........................................16.2 Million (6 bits + FRC)
Pixel Pitch......................................................0.264(H) x 0.264(V)
Color Pixel Arrangement.................................RGB Vertical Stripe
Brightness......................................................300cd/m^2 (Nits)
Response Time..............................................5.5ms
Viewing Angle................................................Horizontal: 140º; Vertical: 130º (Typ.)
Optimum Viewing Direction............................6 o’clock
Backlight Unit……………………………………CCFL, 4 Tables, Edge-Light (2 Top/2 Bottom)
Operating Lamp Life ......................................40,000 – 50,000 hrs
Contrast Ratio…………………………………..500:1
LCD – 17” Hi-Resolution
Display area…………………………………….379.3mm (W) x 244.6 (H) (17.1 inch diagonal) Panel Type………………………………………TFT Active
Number of Pixels ...........................................1920 (H) x 1200 (V)
Color Depth....................................................6 bit,262,144 colors
Pixel Pitch......................................................0.191(H) x 0.191(V)
Brightness......................................................275cd/m2
Operating Lamp Life ......................................10,000 hrs
25
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
LCD – 20.1”
Display area…………………………………….408mm (W) x 306mm (H) (20.1 inch diagonal) Panel Type………………………………………TFT Active
Number of Pixels ...........................................1600 (H) x 1200 (V)
Number of Colors...........................................16.7 Million (8 bits)
Pixel Pitch......................................................0.255(H) x 0.255(V)
Color Pixel Arrangement.................................RGB Vertical Stripe
Brightness......................................................300cd/m^2 (Nits)
Response Time..............................................6ms
Viewing Angle................................................Horizontal: 178º; Vertical: 178º (Typ.)
Optimum Viewing Direction............................6 o’clock
Backlight Unit……………………………………6 CCFL
Operating Lamp Life ......................................45,000 hrs
Contrast Ratio…………………………………..800:1
Display Controller: VGA (-15,-17 & -20)
Connector………………………………………15HD, female
Video Format.................................................VGA,SVGA, XGA, SXGA (17” and 20” only), UXGA (20” only)
Signal Input (from Video Source)…………….Analog RGB
Sync Range...................................................H: 31 ~ 80KHz, V: 55 ~ 76Hz
OSD Control…………………………………….Menu, Up, Down, Select, Power (5 keys)
Plug and Play.................................................VESA DDC 2B Ver1.3
Display Controller: DVI (-17)
Connector……………………………………….DVI-D, female
Video Format.................................................VGA,SVGA, XGA, SXGA
Signal Input (from Video Source)…………….Digital TMDS
Sync Range...................................................H: 31 ~ 80KHz, V: 55 ~ 76Hz
OSD Control…………………………………….Menu, Up, Down, Select, Power (5 keys)
Plug and Play.................................................VESA DDC 2B Ver1.3
OSD Control Board
OSD Control ..................................................5 Keys
Power Key .....................................................Power ON/OFF
Menu Key.......................................................Activates Menu
Up, Down Keys..............................................Navigation Control
Select Key......................................................Select (when in Menu); Auto Adjust (not in menu)
LED................................................................Indicates Operation Status
...............................................................Green = Power-ON, Video Input OK
...............................................................Red = Suspend / Stand-by, or Input Out of Range
Keyboard
No. Of Keys ...................................................83 Keys (US), 84 keys (German, French, Italian, Spanish)
Key Switch Type............................................Membrane switch
Keytop Style...................................................Rectangular Cylindrical
Operating Force.............................................50gf +/- 25gf
Stroke ............................................................3.0mm +/- .5mm
Tactile............................................................20 gf typ.
Height ............................................................8.5 mm
Operating Life................................................10M operations, minimum
Interface ........................................................Row and column matrix
Key Switch Bounce........................................ 10 ms, maximum
Supported Platforms......................................USB, PS/2
CPU Connectors............................................USB Type B (USB);
.........................................6-pin miniDIN, female, Purple & Green (PS/2)
26
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
Touchpad
Motion Detection Method...............................capacitance sensing
X/Y Position Sensing Resolution ...................40 counts/mm
X/Y Position Reporting...................................Relative (Similar to mouse)
Tracking Speed..............................................Up to 1016 mm/sec
Touch Force...................................................No Contact pressure required
Lifetime (Plastic Overlay)...............................Minimum 10,000,000 strokes
Sample Rate..................................................Up to 100 samples/sec
27
NTI RACKMUX-V15/17/20 RACKMOUNT LCD MONITOR WITH KEYBOARD AND MOUSE
TROUBLESHOOTING
Each and every piece of every product produced by Network Technologies Inc is 100% tested to exacting specifications. W e make every effort to insure trouble-free installation and operation of our products. If problems are experienced w hile installing this product, please look over the troubleshooting chart below to see if perhaps we can answer any questio ns that arise. If the answer is not found in the chart, please check the FAQs (Frequently Asked Questions) at our website at http://www.networktechinc.com or contact us directly for help at 1-800-742-8324 (800-RGB-TECH) in US & Canada or 1-330-562­7070 worldwide. We will be happy to assist in any way we can.
Problem/Message Cause Solution
"OUT OF FREQUENCY"
"POWER SAVER MODE" "NO SIGNAL"
"AUTO CONFIGURATION"
Keyboard/touchpad not functioning
Front panel USB port is not working
Keys pressed on the keyboard do not yield the expected result LCD is not displaying image
Input signal is outside the supported range The input signal is not present. This message will disappear after 5 seconds. The input signal is not present immediately after power ON. The LCD monitor is configuring itself for proper communication with the CPU.
• Keyboard is in the incorrect mode
• Cables are not prop erly connected
USB cable is not properly connected Check USB cable connection between the RACKMUX
“Fn” function is locked ON. Check to see if the Fn LED is illuminated. If so, press
• Image out of range
• LCD Auto-Shut OFF button is
depressed
• LCD is powere d OFF
Lower video frequency to be within specified range Check all cable connections- verify that they are
secure Check all cable connections- verify that they are secure No action necessary
• Toggle the keyboard mode from PS/2 (default) to USB. A. If keyboard works in PS/2 mode and not
USB, USB cable is incorrectly connected.
B. If keyboard works in USB mode and not
PS/2, PS/2 cable is incorrectly installed
• Check all cable connections between the RACKMUX and the computer.
and the computer. Make sure it is connected to a working USB port at the CPU.
the “Fn” key twice quickly to unlock the function.
• Lower the resolution
• Make sure nothing is resting on the button
• Turn power to LCD ON
INDEX
accessory USB port, 6
Display functions, 11 Function key, 19 Java Runtime Environment, 8
kvm on IP password, 7, 8 KVM-on-IP, 6
Materials included, 1
Number Pad, 20 numeric keypad, 22
WARRANTY INFORMATION
The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network Technologies Inc at for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns.
MAN047 Rev. 5/9/13
(800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at http://www.networktechinc.com
OSD Controls, 11 OSD Menu-DVI, 13 Power up sequence, 10
Rack mounting, 3
Specifications, 25
Telco mount, 4 USB port, 6 USB-PS/2 mode, 23
28
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use