Page 1
Installation Guide
10 GigaBit Media Converter
800-0225-001 PUBFMCXFPU Rev. A 11/12
Page 2
PLEASE READ THESE LEGAL NOTICES CAREFULLY.
By using a Net Optics 10 GigaBit Media Converter you agree to the terms and conditions of usage set forth by Net Optics, Inc.
No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics retains all intellectual
property rights associated with the technology described in this manual. This manual is intended to assist application in installing Net Optics
products into your network.
Trademarks and Copyrights
© 2012 by Net Optics, Inc. Net Optics® is a registered trademark of Net Optics, Inc. Additional company and product names may be trademarks
or registered trademarks of the individual companies and are respectfully acknowledged.
Additional Information
Net Optics, Inc. reserves the right to make changes in specications and other information contained in this document without prior notice. Every
effort has been made to ensure that the information in this document is accurate.
Page 3
Contents
Introduction .............................................................................1
Key Features ............................................................................1
About this Guide .........................................................................2
Unpacking and Inspection ..................................................................2
Product Diagram ........................................................................2
Installing the Media Converter ..............................................................3
Installing a Conversion Kit .................................................................3
10 GigaBit Ethernet Connection Distances ....................................................4
Specications ...........................................................................5
Limitations on Warranty and Liability ........................................................6
3.3
10 GigaBit Media Install Guide
Page 4
Introduction
Net Optics 10 GigaBit Converters are optimized, high-performance media converters for connecting dissimilar 10
GigaBit devices and links. Deploy these bidirectional media converters individually to connect SR and LR ber
devices, or in pairs at each end of long-distance ber links. These Converters are the perfect solution for dispersed
networks where media conversion is required between multimode segments separated by long distances.
Fast and Versatile
The 10 GigaBit Converters support seamless media conversion at 10 Gbps over link distances up to 65 meters with
50/125 multimode SR ber and up to 10 kilometers with singlemode LR ber. These Converters feature XFP module
connectors for quick reconguration and redeployment.
Long Link Reliability
To control jitter over long optical links, the Converter features Clock and Data Recovery (CDR). CDR ensures that the
overall jitter budget is not exceeded when deploying converter pairs with long ber links.
Simple and Reliable
Media conversion is a snap since all network and monitoring cables necessary for plug-and-play deployment are
included with the Tap. For extra uptime protection, Net Optics Converters offer redundant power connections. Should
the primary power source fail, the Converter automatically switches to the backup power source with no trafc
interruption.
10 GigaBit Media Install Guide
Key Features
Secure Technology
• Optimized and tested for 10 GigaBit ber networks
• Provides transparent conversion at 10 Gbps without data stream interference or introducing a point of failure
• Clock and Data Recovery (CDR) control overall jitter when deploying converter pairs
• Redundant power ensures link uptime
• Compatible with all LR singlemode ber and SR multimode ber
• Fully IEEE 802.3ae compliant
• Fully RoHS compliant
Ease of Use
• LED indicators show link status and redundant power
• Optional 19-inch rack frame holds three Converters
• Compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and
intrusion detection/prevention systems
Support
• Our technical support team is available from 8 am to 5 pm Pacic Time, Monday through Friday at 1 (408) 7377777 and via email at support@netoptics.com.
1
Page 5
About this Guide
This guide covers the installation and use of the following models:
Part Number Description
FMC-XFP 10 GigaBit Converter
Unpacking and Inspection
Unpack the 10 GigaBit Media Converter, verify that you have all components by checking the Packing List against
goods received.
The 10 GigaBit Media Converter ships with the following:
• 2 Power supplies
• 2 Network cables
• 1 Installation Guide
You may have also ordered a panel for rack mounting the Converter and an extended warranty. If any part is missing or
damaged, immediately contact Net Optics Customer Service at 1 (408) 737-7777.
If you need to change the interface on the Converter, Net Optics offers kits that include the XFP and corresponding
cable.
10 GigaBit Media Install Guide
The kits are:
XFPKT-50SR 10GBase-SR XFP Kit 50µm
XFPKT-SR 10GBase-SR XFP Kit
XFPKT-LR 10GBase-LR XFP Kit
XFP kits are ordered separately. For more information, contact Net Optics Customer Service, 1 (408) 737-7777.
Product Diagram
Front Panel
www.netoptics.com
XFP Connector XFP Connector
®
A
LINK
A
B
B
10 GigaBit Converter
2
1
Product Diagram
2
Page 6
Installing the Media Converter
Warning: ______________________________________________________________________________________
The intended use of this product is in systems that contain lasers.
________________________________________________________________________________________________
DANGER: ______________________________________________________________________________________
Invisible Laser Radiation when open or when operating with ber disconnected. AVOID DIRECT EXPOSURE TO THE
BEAM. Never operate unit with a broken ber or with a ber connector disconnected.
________________________________________________________________________________________________
To install the Converter:
1. If you are rack mounting the Converter, install the panel in the rack with the four thumbscrews provided.
2. Insert the Converter into one of the available slots and secure it to the panel by tightening the thumbscrews.
3. Using the supplied cables, connect the Converter ports to the corresponding devices.
4. Connect the redundant power supplies to separate power sources and then to the converter.
10 GigaBit Media Install Guide
5. Secure the DC power connectors with the connector clips.
6. Check the Power LEDs to verify that the Converter is receiving power.
7. Check the Link LEDs to verify that the link has been established.
Installing a Conversion Kit
The conversion kits include the XFP and matching cable. Remove power from the Converter before installing the
conversion kit.
To change the XFP:
1. Remove the cable and lower the wire clip to release the old XFP.
2. With the clip in the lowered position, pull gently on the clip to free the XFP.
3. Insert the new XFP until you hear it click into place.
4. Connect the approriate cable and check the Link LEDs.
Installing a Conversion Kit
3
Page 7
10 GigaBit Ethernet Connection Distances
10GB-SR (850 nm laser)
10 GigaBit Media Install Guide
Fiber Core
Diameter
62.5 µm
62.5 µm Multimode 200 Mhz/km 33 m
50.0 µm Multimode 400 Mhz/km 66 m
50.0 µm Multimode 500 Mhz/km 83 m
50.0 µm Multimode 2007 Mhz/km 300 m
Type
Multimode 160 Mhz/km 26 m
Fiber
Bandwidth
Mhz/km
10GB-LR (1310 nm laser)
Fiber Core
Diameter
8.5 µm Singlemode n/a up to 10 Km
Type
Fiber
Bandwidth
Mhz/km
Distance
Distance
10 GigaBit Ethernet Connection Distances
4
Page 8
Specications
Environmental
Operating Temperature: 0˚C to 40˚C
Storage Temperature: -10˚C to 70˚C
Relative Humidity: 10% min, 95% max, non-condensing
Mechanical
Dimensions: 1.0” high x 5.3” deep x 2.9” wide
Power
Power Supply: Input: 100-240 VAC, 0.6A (max), 50-60 Hz
Output: 1.5A@12VDC
Certications
Fully RoHS compliant
Connectors
FMC-XFP
(2) XFP hot-pluggable
10 GigaBit Media Install Guide
XFP Conversion Kits (o rdere d separately)
XFPKT-50SR 10GBase-SR XFP Kit 50µm
XFPKT-SR 10GBase-SR XFP Kit
XFPKT-LR 10GBase-LR XFP Kit
Specications
5
Page 9
10 GigaBit Media Install Guide
Limitations on Warranty and Liability
Net Optics offers a limited warranty for all its products. IN NO EVENT SHALL NET OPTICS, INC. BE LIABLE FOR ANY
DAMAGES INCURRED BY THE USE OF THE PRODUCTS (INCLUDING BOTH HARDWARE AND SOFTWARE)
DESCRIBED IN THIS MANUAL, OR BY ANY DEFECT OR INACCURACY IN THIS MANUAL ITSELF. THIS INCLUDES
BUT IS NOT LIMITED TO LOST PROFITS, LOST SAVINGS, AND ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT, even if Net Optics has been advised of the possibility of
such damages. Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Net Optics, Inc. warrants this Tap to be in good working order for a period of ONE YEAR from the date of purchase from Net
Optics or an authorized Net Optics reseller.
Should the unit fail anytime during the said ONE YEAR period, Net Optics will, at its discretion, repair or replace the product. This
warranty is limited to defects in workmanship and materials and does not cover damage from accident, disaster, misuse, abuse or
unauthorized modications.
If you have a problem and require service, please call the number listed at the end of this section and speak with our technical
service personnel. They may provide you with an RMA number, which must accompany any returned product. Return the product
in its original shipping container (or equivalent) insured and with proof of purchase.
Additional Information
Net Optics, Inc. reserves the right to make changes in specications and other information contained in this document without prior
notice. Every effort has been made to ensure that the information in this document is accurate. Net Optics is not responsible for
typographical errors.
THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, EXPRESS
OR IMPLIED. No Net Optics reseller, agent, or employee is authorized to make any modication, extension, or addition to this
warranty.
Net Optics is always open to any comments or suggestions you may have about its products and/or this manual.
Send correspondence to
Net Optics, Inc.
5303 Betsy Ross Drive
Santa Clara, CA 95054 USA
Telephone: +1 (408) 737-7777
Fax: +1 (408) 745-7719
E-mail: info@netoptics.com / Internet: www.netoptics.com
All Rights Reserved. Printed in the U.S.A. No part of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any form, by any means, without prior written consent
of Net Optics, Inc., with the following exceptions: Any person is authorized to store documentation on a single computer for
personal use only and that the documentation contains Net Optics’ copyright notice.
Limitations on Warranty and Liability
6
Page 10
www.netoptics.com
© 2008-2012 by Net Optics, Inc. All Rights Reserved.
Loading...