NetMedia VIDLAMP-DI User Manual
NM-VIDLAMP
Security Video Camera
Indoor/Outdoor Weather Resistant
Color
The NetMedia VIDLAMP security cameras mount to a typical round 4 inch junction box and are viewed with a security
monitor. Other junction boxes from your local hardware store may also be used after replacing the round base with another
that has a 1/2 inch diameter hole for the elbow bracket. To view the cameras on a single standard television, use the TV’s
composite RCA Video Input jack.
Product Includes:
1. Camera Assembly (Camera, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base, Gasket, Video Connector; Power Connector).
2. 12V DC 300mA Power Transformer (Center Conductor Positive).
3. Mounting hardware (Mounting Screws, Grounding
Strap, Screw and Compression Ring).
Housing
Available in Ivory only:
Model Camera Type
NM-VIDLAMP-CI
NM-VIDLAMP-DI
Elbow Bracket
Adjusts camera angle at base,
screw, and housing. Installs in
1/2” junction box covers.
Color
Day/Night Color
Color
Camera Lens
Comes prefocused from
factory but can be adjusted
by rotating in either direction.
Camera Bracket
Slot indicates image bottom;
rotate to adjust camera.
Housing Cap
Remove to rotate camera
bracket or to adjust focus.
Day/Night
Locking Ring
Secures elbow bracket to
base at desired position.
Video Connector
Female BNC connector.
FEATURES SPECIFICATIONS Color
Excellent image quality
Tough aluminum housing
Weather resistant enclosure
Internally routed cables
Mounts to standard electrical xtures
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply
One year limited warranty
Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Output Connector:
Power Requirement:
Power Connector:
Housing Size:
Base Size:
Mounting Holes:
Weight:
3.7mm
1/4” CCD
470 lines
54˚ Horizontal
0.5 Lux F1.2
5.5mm OD, 2.1mm ID, center positive
Base, Gasket & Screws
Mount to round 4” junction box.
Power Connector
12V DC 300mA, center positive.
Day/Night Color
No
Female BNC, 75 Ohm
12V DC, 300mA
3.13“ dia., 4” long
4.5” dia., 0.75” high, 0.5“ hole
3.5” centers
1 lb.
(subject to change without notice)
NM-VIDLAMP
3.6mm
1/3” CCD
540 lines
72˚ Horizontal
0.1 Lux
Yes
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
MAN-VIDLAMP REV1003A
NM-VIDLAMP
DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.
Installation Procedures:
1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information.
2. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s
Video Connector. Adapters, such as BNC to F or RCA, may be used where appropriate.
3. Connect the 12V DC 300mA Power Transformer from an AC outlet to the camera’s Power Input Connector.
4. Mount the base to the junction box (not included) and adjust the camera assembly for proper viewing. When
satisfied, secure all adjustment points.
Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In
jack and view through its video or line input. The picture will not be available on a channel.
Camera
Video Cable
Monitor
or
Television
Quad.
Sequencer
or
DVR
Camera
Monitor
or
Television
Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a
loopback or video output jack.
Distribution
Panel
or Splitter
Television
Television
Camera
Main cable or
antenna
Modulator
AMP
Amplifier
Splitter/
Combiner
Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on
the modulated channel. The modulator can also be the last piece of equipment in Figure 2.
To Next
Device
NM-VIDLAMP
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
MAN-VIDLAMP REV1003A
Loading...