NetMedia UTPVCAM-DW User Manual

UTP Security Camera

NM-UTPVCAM

Varifocal Day/Night Color

The NetMedia UTPVCAM Varifocal color camera manually zooms from 3.5mm to 8.0mm in focal length to meet a variety of
surveillance requirements. It utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to exchange
power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple cables to the
camera location! It mounts to a typical round 4 inch junction box and is viewed with a security monitor or television. To view
the camera on a single standard television, use the TV’s composite RCA Video Input jack.

Product Includes:

1. Camera Assembly (Camera, Housing, Varifocal Lens, Lens Casing, Elbow
Bracket, Locking Ring, Base, Gasket, UTP Video Encoder, UTP Jack).
NetMedia UTP Video Decoder and 24V DC 200mA Power Transformer.

2.
Mounting Screws and RCA Video Cable.

3.

Housing

Available in white: NM-UTPVCAM-DW
Connects to Lens Casing at this point.

UTP Video Encoder

Built into camera - exchanges
power and video with Decoder for
One Wire Video™ on UTP cable.

Indoor/Outdoor Weather Resistant

Varifocal Lens

Not shown - manually adjust

focus, iris, and zoom

(focal length 3.5mm to 8.0mm).

Lens Casing

Remove to access Varifocal Lens.

Threaded to accept external

37mm lenses and accessories.

NM-UTPVCAM

Elbow Bracket

Adjusts camera angle at base,
screw, and housing.

UTP Jack

Female RJ-45 connector transmits
both power and video across CAT5
and other UTP cable types.

Red LED

Indicates Power.

UTP Jack

Connects to Camera UTP
Jack via straight-through
wired UTP cable (T-568A).

Power Input

Connects to 24V DC wall
transformer (included)
and AC outlet.

UTP Video Decoder

FEATURES

3.5mm to 8.0mm zoom lens
UTP Video Encoder built into camera
Includes UTP Video Decoder module
One Wire Video™ Installation
Uses one inexpensive UTP cable
Supports up to 1000 ft of UTP cable
Supports industry standard wiring schemes
Excellent image quality
Tough billet aluminum housing
Weather resistant enclosure
Internally routed cables
Mounts to standard electrical xtures
Mounts directly to walls and ceilings
Works in low light conditions
Accepts photo lens accessories
Adjustable camera angles
Tamper resistant wiring
Includes power supply
One year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

RCA Video Out

Connects to viewing
device such as monitor,
DVR, TV, or modulator.

SPECIFICATIONS

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Camera/Decoder Cable Connector:
Camera/Decoder Cable Type:
Camera/Decoder Cable Distance Range:
Camera/Decoder Video Signal:
UTP Decoder Video Output:
UTP Decoder Video Output Connector:
UTP Decoder Power Input:
UTP Decoder Power Connector:
UTP Decoder Size:
UTP Decoder Weight:
External Accessory Threads:
Housing Size:
Base Size:
Base Mounting Holes:
Assembly Weight:

Base, Gasket & Screws

Mount to round 4” junction box.

Locking Ring

Secures elbow bracket to

base at desired position.

Sharpen image after setting zoom.

Zoom in (T ) or out (W) as desired.

Day/Night Color

3.5mm to 8.0mm Varifocal

75˚ to 32˚ Horizontal

Female RJ-45 jack

UTP: CAT5 or better

24V DC, 200mA

5.5mm OD, 2.1mm ID, center positive

3.2” long, 2.2” wide, 0.9” thick

37mm x .75 pitch

2.3” dia. x 4.2” long

4.5“ dia., 0.75” high, 0.5“ hole

Focus Adjustment

Zoom Adjustment

1/3” CCD

540 lines

0.1 Lux
Yes

Up to 1000’
Proprietary

Composite

Female RCA

3 oz.

3.5” centers
1 lb.

(subject to change without notice)

MAN-UTPVCAM REV1003A

NM-UTPVCAM

DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair
needs a dedicated point-to-point wiring circuit. If attaching your own plugs, wire them for straight-through connec­tions: pin1 to pin1, pin2 to pin2; pin3 to pin3, etc. For standardization, you should also follow the T-568A color specifi­cation but it will not affect the camera’s function. Do not connect the UTP cable to computer networks or other

UTP video systems! Doing so could damage this product and/or the other attached devices!

2. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
jack. Simple adapters, such as RCA to BNC, may be used where appropriate.

3. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.

4. Mount the base to the junction box (not included) and direct the camera assembly towards the intended viewing
area. Remove the Lens Casing and loosen the zoom and focus set screws. Adjust the zoom and focus of the Varifocal
Lens for proper viewing. When satisfied, secure all adjustment points.

Up to 1000 Feet

Video CableUTP Cable

Camera

UTP Video Decoder Module

Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In

jack and view through its video or line input. The picture will not be available on a channel.

Monitor

or

Television

NM-UTPVCAM

Quad.

Sequencer

or

DVR

Camera

UTP Cable

UTP Video Decoder Module

Monitor

or

Television

Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

Camera

Main cable or

antenna

UTP Cable

UTP Video Decoder Module

Modulator

AMP

Amplifier

Splitter/

Combiner

Distribution

Panel

or Splitter

Television

Television

Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on

the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

To Next

Device

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-UTPVCAM REV1003A