NetMedia UTPJBOX-DB User Manual

NM-UTPJBOX

UTP Security Camera

In-Wall Junction Box Mounted

Color

This general purpose surveillance camera utilizes a built-in NetMedia UTP Video Encoder and external UTP Video Decoder to
exchange power and video across a single Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple
cables to the camera location! It mounts in a typical single gang junction (light switch) box and is viewed with a security
monitor or television. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack.

Product Includes:

1. Camera Assembly (Camera, Camera Bracket, UTP Video Encoder).

2. NetMedia UTP Video Decoder and 24V DC 200mA Power Transformer.

3. Mounting Screws and RCA Video Cable.

4. Two Lens Cover Inserts (Dark Lens Cover, Clear Lens Cover).

Cover Plate

Not Included

Camera Bracket

Bends to adjust angle of view.

Lens Cover

Dark or Clear cover snaps

into Cover Plate.

Day/Night

Color

Camera Assembly

Camera, Bracket,

UTP Video Encoder.

Camera Lens

Factory set - rotates in either

direction to adjust focus.

Junction Box

Not Included

UTP Video Encoder

Exchanges power and video with Decoder

for One Wire Video™ on UTP cable.

Model Camera Type

NM-UTPJBOX-C
NM-UTPJBOX-D

Female RJ-45 connector transmits

both power and video across CAT5

and other UTP cable types.

Color
Day/Night Color

UTP Jack

NM-UTPJBOX

UTP Jack

Connects to Camera UTP
Jack via straight-through
wired UTP cable (T-568A).

Power Input

Connects to 24V DC wall
transformer (included)
and AC outlet.

FEATURES

UTP Video Encoder built into camera

Includes UTP Video Decoder module

One Wire Video™ Installation

Uses one inexpensive UTP cable

Excellent image quality

Internally routed cables

Mounts in standard electrical xtures

Mounts in walls and ceilings

Works in low light conditions

Adjustable camera angles

Tamper resistant wiring

Includes power supply

One year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

UTP Video Decoder

Red LED

Indicates Power.

RCA Video Out

Connects to viewing
device such as monitor,
DVR, TV, or modulator.

SPECIFICATIONS Color Day/Night Color

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Camera/Decoder Cable Connector:
Camera/Decoder Cable Type:
Camera/Decoder Cable Distance Range:
Camera/Decoder Video Signal:
UTP Decoder Video Output:
UTP Decoder Video Output Connector:
UTP Decoder Power Input:
UTP Decoder Power Connector:
UTP Decoder Size:
UTP Decoder Weight:
Assembly Size:
Assembly Weight:

3.7mm
1/4” CCD
470 lines

54˚ Horizontal

0.5 Lux F1.2
No

Female RJ-45 jack

UTP: CAT5 or better

Up to 1000’
Proprietary

Composite

Female RCA

24V DC, 200mA

5.5mm OD, 2.1mm ID, center positive

3.2” long, 2.2” wide, 0.9” thick
3 oz.

4“ high, 1.9” wide, 1.5“ deep

3.5 oz.

(subject to change without notice)

3.6mm
1/3” CCD
540 lines

72˚ Horizontal

0.1 Lux

Yes

MAN-UTPJBOX REV1004A

NM-UTPJBOX

DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair
needs a dedicated point-to-point wiring circuit. If attaching your own plugs, wire them for straight-through connec­tions: pin1 to pin1, pin2 to pin2; pin3 to pin3, etc. For standardization, you should also follow the T-568A color specifi­cation but it will not affect the camera’s function. Do not connect the UTP cable to computer networks or other

UTP video systems! Doing so could damage this product and/or the other attached devices!

2. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
jack. Simple adapters, such as RCA to BNC, may be used where appropriate.

3. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.

4. Install Camera Assembly into the Junction Box (not included) and adjust for proper viewing.

5. Snap the dark or clear Lens Cover into the Cover Plate (not included) by pressing all four corners in simultaneously.

6. Attach the Cover Plate to the Junction Box. Silicon or similar sealant may be used as needed.

Up to 1000 Feet

Video Cable UTP Cable

Camera

UTP Video Decoder Module

Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In

jack and view through its video or line input. The picture will not be available on a channel.

Monitor

Television

NM-UTPJBOX

or

Quad.

Sequencer

or

DVR

Camera

UTP Cable

UTP Video Decoder Module

Monitor

or

Television

Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

Camera

Main cable or

antenna

UTP Cable

UTP Video Decoder Module

Modulator

AMP

Amplifier

Splitter/

Combiner

Distribution

Panel

or Splitter

Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on

the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

To Next

Device

Television

Television

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-UTPJBOX REV1004A