Net Media SCE2, SCE3, SCE1 Specifications

NM-VIDLAMP

(SCE1 SCE2 SCE3)

B/W Color

The NetMedia VIDLAMP (SCE1, SCE2, SCE3) security cameras mount to a typical round 4 inch junction box and are viewed
with a security monitor. Other junction boxes from your local hardware store may also be used after replacing the round
base with another that has a 1/2 inch diameter hole for the elbow bracket. To view the cameras on a single standard televi­sion, use the TV’s composite RCA Video Input jack.

Product Includes:

1. Camera Assembly (Camera, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base, Gasket, Video Connector; Power Connector).

2. 12V DC 300mA Power Transformer (Center Conductor Positive).

3. Mounting hardware (Mounting Screws, Grounding
Strap, Screw and Compression Ring).

Day/Night

Color

Indoor/Outdoor Weather Resistant

Security Video Camera

Housing

Available in Ivory only:

Model Camera Type

(SCE1) NM-VIDLAMP-BI

(SCE2) NM-VIDLAMP-CI

(SCE3) NM-VIDLAMP-HI

B&W

Color

Day/Night Color

by rotating in either direction.

Elbow Bracket

Adjusts camera angle at base,
screw, and housing. Installs in
1/2” junction box covers.

Base, Gasket & Screws

Mount to round 4” junction box.

Video Connector

Female BNC connector.

Power Connector

12V DC 300mA, center positive.

FEATURES SPECIFICATIONS B/W Color

Excellent image quality
Tough aluminum housing
Weather resistant enclosure
Internally routed cables
Mounts to standard electrical xtures
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply
1 year limited warranty

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Output Connector:
Power Requirement:
Power Connector:
Housing Size:
Base Size:
Mounting Holes:
Weight:

3.6mm
1/3” CCD
350 lines

72˚ Horizontal

0.7 Lux F2.0
Yes

5.5mm OD, 2.1mm ID, center positive

3.7mm
1/4” CCD
470 lines

54˚ Horizontal

0.5 Lux F1.2

Female BNC, 75 Ohm

12V DC, 300mA

3.13“ dia., 4” long

4.5” dia., 0.75” high, 0.5“ hole

3.5” centers

Camera Lens

Comes prefocused from

factory but can be adjusted

Camera Bracket

Slot indicates image bottom;

rotate to adjust camera.

Housing Cap

Remove to rotate camera

bracket or to adjust focus.

Locking Ring

Secures elbow bracket to

base at desired position.

Day/Night Color

3.6mm
1/3” CCD
580 lines

72˚ Horizontal

0.3 Lux F1.2

No

1 lb.

(subject to change without notice)

Yes

NM-VIDLAMP

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-VIDLAMP REV0707A

NM-VIDLAMP (SCE1 SCE2 SCE3)

DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Ensure that the camera is grounded with the ground strap as shown in the FCC Information.

2. Connect a grounded video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s
Video Connector. Adapters, such as BNC to F or RCA, may be used where appropriate.

3. Connect the 12V DC 300mA Power Transformer from an AC outlet to the camera’s Power Input Connector.

4. Mount the base to the junction box (not included) and adjust the camera assembly for proper viewing. When
satisfied, secure all adjustment points.

Camera

Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In

jack and view through its video or line input. The picture will not be available on a channel.

Video Cable

Monitor

or

Television

Quad.

Sequencer

or

DVR

Camera

Monitor

or

Television

Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

Distribution

Panel

or Splitter

Television

Television

Camera

Main cable or

antenna

Modulator

AMP

Amplifier

Splitter/

Combiner

Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on

the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

To Next

Device

NM-VIDLAMP

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-VIDLAMP REV0707A