NetMedia POCSET User Manual

PoC Encoder/Decoder Set

NM-POCSET

The NetMedia Power over Coax PoC Video Encoder and Decoder modules allow popular 12V DC cameras to use one coax
cable, such as RG6, for both power and video. There is no need to run multiple cables to the camera location! The modules
support cable distances up to 100 feet. To view the video, use a security monitor or the composite RCA Video Input jack of
a television.

Product Includes:

1. NetMedia PoC Video Encoder module.

2. NetMedia PoC Video Decoder module.

3. 24V DC 200mA Power Transformer.

3. Power Extension Cable and two RCA Video Cables.

Video and Power Transmission Device

F-Connector

Connects to Decoder
F-Connector via coax cable.

Power Output

Provides 12V DC 150mA
power for camera.

F-Connector

Connects to Encoder
F-Connector via coax cable.

Power Input

Uses 24V DC from included
Power Transformer.

PoC Video Encoder

PoC Video Decoder

Power Extension Cable

Connects to 12V DC power
input of camera.

RCA Video In

Connects to video
output of camera.

Power Transformer

Connects to 24V DC Power
Input of Decoder and AC outlet.

RCA Video Out

Connects to viewing
device such as monitor,
DVR, TV, or modulator.

FEATURES

One Wire Video™ Installation

Supports popular color and B/W cameras

Provides remote 12V DC 150mA power

Uses one coax for power and video

Uses pre-existing coax cable

Supports up to 100 ft with color and B/W

Supports standard F-connectors

Sturdy aluminum boxes

Includes power supply

1 year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

SPECIFICATIONS

Input/Output Video Connector:
Input/Output Video Signal:
Encoder/Decoder Video Connector:
Encoder/Decoder Video Signal:
Encoder/Decoder Cable Type:
Encoder/Decoder Cable Distance Range:
PoC Encoder Size:
PoC Encoder Weight:
PoC Encoder Power Output:
PoC Encoder Power Connector:
PoC Decoder Size:
PoC Decoder Weight:
PoC Decoder Power Input:
PoC Decoder Power Connector:

Female RCA

Composite

Female F-Connector

Proprietary

Coax: RG6 quad shield recommended

Up to 100’

3.2” long, 2.2” wide, 0.9” thick
3 oz.

12V DC, 150mA

5.5mm OD, 2.1mm ID, center positive

3.2” long, 2.2” wide, 0.9” thick
3 oz.

24V DC, 200mA

5.5mm OD, 2.1mm ID, center positive

(subject to change without notice)

MAN-POCSET REV0703A

NM-POCSET

NM-POCSET

Camera

Camera

Camera

Installation Procedures:

1. Connect a coax cable (RG6 recommended) to the F-Connectors of the Video Encoder and Decoder. Each
Encoder/Decoder pair needs a dedicated point-to-point wiring circuit.

to other video distribution equipment! Doing so could damage this product and/or the other attached devices!

2. Connect a video cable from the camera to the Encoder’s RCA Video In jack. Simple adapters, such as RCA to BNC, may
be used where appropriate.

3. Connect the Power Extension Cable from the Encoder’s Power Output Connector to the camera’s 12V DC power input.
If the camera requires more than 150mA or if it does not use 12V DC then it cannot use the Encoder’s power output.

4. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
jack using appropriate adapters where necessary.

5. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.

Up to 100 Feet

Do not connect the Encoder/Decoder coax

24 VDC

INPUT

Video Cable

Monitor

Television

Camera

Video Cable

12 VDC

OUTPUT

Coax Cable

POWER

VIDEO

PoC Video Decoder ModulePoC Video Encoder Module

Figure 1 - Connecting the modules to a security monitor or standard television. Use the TV’s composite RCA Video

In jack and view through its video or line input. The picture will not be available on a channel.

Quad

Sequencer

or

DVR

Video Cable

Monitor

or

Television

Camera

12 VDC

OUTPUT

Coax Cable

POWER

VIDEO

24 VDC

INPUT

PoC Video Decoder ModulePoC Video Encoder Module

Figure 2 - Connecting the modules to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

or

To Next

Device

Modulator

AMP

Amplifier

Splitter/

Combiner

Distribution Panel

or Splitter

Camera

Main cable or

antenna

12 VDC

OUTPUT

Coax Cable

POWER

VIDEO

24 VDC

INPUT

PoC Video Decoder ModulePoC Video Encoder Module

Figure 3 - Connecting the modules to a modulator for whole house distribution and standard television viewing

on the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

Television

Television

NM-POCSET

MAN-POCSET REV0703A