NetMedia POCLAMP-DI User Manual
NM-POCLAMP
Power over Coax Camera
Indoor/Outdoor Weather Resistant
Color
This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external
PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple
cables to the camera location! It mounts to a typical round 4 inch junction box and is viewed with a security monitor or
television. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack.
Product Includes:
1. Camera Assembly (Camera, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base, Gasket, PoC Video Encoder, F-Connector).
2.
NetMedia PoC Video Decoder and 24V DC 200mA Power Transformer.
3. Mounting Screws and RCA Video Cable.
Housing
Available in Ivory Color Only:
Color camera Day/Night Color Housing
NM-POCLAMP-CI
Elbow Bracket
Adjusts camera angle at base,
screw, and housing.
F-Connector
Transmits both power and video
across a single coax.
F-Connector
Connects to camera
F-Connector with a single
coax such as RG6.
NM-POCLAMP-DI
Day/Night Color
PoC Video Encoder
Built into camera - exchanges
power and video with Decoder for
One Wire Video™ on coax cable.
Camera Lens
Factory set - rotates in either
direction to adjust focus.
Ivory
Camera Bracket
Slot indicates image bottom.
Housing Cap
Provides access to camera.
Base, Gasket & Screws
Mount to round 4” junction box.
Locking Ring
Secures elbow bracket to
base at desired position.
PoC Video Decoder (Included)
NM-POCLAMP
Power Input
Connects to 24V DC wall
transformer (included)
and AC outlet.
FEATURES
PoC Video Encoder built into camera
Includes PoC Video Decoder module
One Wire Video™ Installation
Uses one coax cable to camera
Excellent image quality
Internally routed cables
Mounts to standard electrical xtures
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply
One year limited warranty
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
SPECIFICATIONS
Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Camera/Decoder Cable Connector:
Camera/Decoder Cable Type:
Camera/Decoder Cable Distance Range:
Camera/Decoder Video Signal:
PoC Decoder Video Output:
PoC Decoder Video Output Connector:
PoC Decoder Power Input:
PoC Decoder Power Connector:
PoC Decoder Size:
PoC Decoder Weight:
Housing Size:
Base Size:
Base Mounting Holes:
Assembly Weight:
RCA Video Out
Connects to viewing
device such as monitor,
DVR, TV, or modulator.
Color Day/Night Color
3.7mm
1/4” CCD
470 lines
54˚ Horizontal
0.5 Lux F1.2
No
Female F-Connector
Coax: RG6 quad shield recommended
Up to 100’
Proprietary
Composite
Female RCA
24V DC, 200mA
5.5mm OD, 2.1mm ID, center positive
3.2” long, 2.2” wide, 0.9” thick
3 oz.
3.13” dia. x 4” long
4.5“ dia., 0.75” high, 0.5“ hole
3.5” centers
1 lb.
3.6mm
1/3” CCD
540 lines
72˚ Horizontal
0.1/0 Lux
(subject to change without notice)
MAN-POCLAMP REV1002A
Yes
NM-POCLAMP
DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.
Installation Procedures:
1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each
Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to
video distribution equipment! Doing so could damage this product and/or the other attached devices!
2. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
Connector. Simple adapters, such as RCA to BNC, may be used where appropriate.
3. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.
4. Mount the Base to the junction box (not included) and adjust the camera assembly for proper viewing. When
satisfied, secure all adjustment points.
Up to 100 Feet
Video Cable Coax Cable
Camera
PoC Video Decoder Module
Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In
jack and view through its video or line input. The picture will not be available on a channel.
Monitor
or
Television
NM-POCLAMP
Quad.
Sequencer
or
DVR
Camera
Coax Cable
PoC Video Decoder Module
Monitor
or
Television
Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a
loopback or video output jack.
Camera
Main cable or
antenna
Coax Cable
PoC Video Decoder Module
Modulator
AMP
Amplifier
Splitter/
Combiner
Distribution
Panel
or Splitter
Television
Television
Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on
the modulated channel. The modulator can also be the last piece of equipment in Figure 2.
To Next
Device
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
MAN-POCLAMP REV1002A
Loading...