NetMedia POCJBOX-DB User Manual

Power over Coax Camera

NM-POCJBOX-DB

Day/Night Color

This general purpose surveillance camera utilizes a built-in NetMedia Power over Coax (PoC) Video Encoder and external
PoC Video Decoder to exchange power and video across a single coax cable, such as RG6. There is no need to run multiple
cables to the camera location! It mounts in a typical single gang junction (light switch) box and is viewed with a security
monitor or television. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack.

Product Includes:

1. Camera Assembly (Camera, Camera Bracket, PoC Video Encoder, F-Connector Cable).

2. NetMedia PoC Video Decoder and 24V DC 200mA Power Transformer.

3. Mounting Screws and RCA Video Cable.

4. Two Lens Cover Inserts (Dark Lens Cover, Clear Lens Cover).

Cover Plate

Not Included

Lens Cover

Dark or Clear cover snaps

into Cover Plate.

Camera Assembly

Camera, Bracket,

PoC Video Encoder.

In-Wall Junction Box Mounted

Junction Box

Not Included

NM-POCJBOX

Camera Bracket

Bends to adjust angle of view.

F-Connector

Connects to camera
F-Connector with a single
coax such as RG6.

Power Input

Connects to 24V DC wall
transformer (included)
and AC outlet.

Factory set - rotates in either

direction to adjust focus.

FEATURES

PoC Video Encoder built into camera
Includes PoC Video Decoder module
One Wire Video™ Installation
Uses one coax cable to camera
Excellent image quality
Internally routed cables
Mounts to standard electrical xtures
Mounts in walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply
One year limited warranty

Camera Lens

Exchanges power and video with Decoder

for One Wire Video™ on coax cable.

PoC Video Decoder (Included)

SPECIFICATIONS

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Camera/Decoder Cable Connector:
Camera/Decoder Cable Type:
Camera/Decoder Cable Distance Range:
Camera/Decoder Video Signal:
PoC Decoder Video Output:
PoC Decoder Video Output Connector:
PoC Decoder Power Input:
PoC Decoder Power Connector:
PoC Decoder Size:
PoC Decoder Weight:
Assembly Size:
Assembly Weight:

PoC Video Encoder

Female F-Connector transmits both

F-Connector

power and video across coax.

RCA Video Out

Connects to viewing
device such as monitor,
DVR, TV, or modulator.

3.6mm

1/3” CCD

540 lines

72˚ Horizontal

0.1 Lux
Yes

Female F-Connector

Coax: RG6 quad shield recommended

Up to 100’

Proprietary

Composite

Female RCA

24V DC, 200mA

5.5mm OD, 2.1mm ID, center positive

3.2” long, 2.2” wide, 0.9” thick
3 oz.

4“ high, 1.9” wide, 1.5“ deep

3.5 oz.

(subject to change without notice)

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-POCJBOX REV1005A

NM-POCJBOX

DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Connect a coax cable (RG6 recommended) to the F-connectors of the camera and Video Decoder. Each
Camera/Decoder pair needs a dedicated point-to-point wiring circuit. Do not connect the Camera/Decoder coax to
video distribution equipment! Doing so could damage this product and/or the other attached devices!

2. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
Connector. Simple adapters, such as RCA to BNC, may be used where appropriate.

3. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.

4. Install Camera Assembly into the Junction Box (not included) and adjust for proper viewing.

5. Snap the dark or clear Lens Cover into the Cover Plate (not included) by pressing all four corners in simultaneously.

6. Attach the Cover Plate to the Junction Box. Silicon or similar sealant may be used as needed.

Up to 100 Feet

Video Cable Coax Cable

Camera

PoC Video Decoder Module

Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In

jack and view through its video or line input. The picture will not be available on a channel.

Monitor

Television

NM-POCJBOX

or

Quad.

Sequencer

or

DVR

Coax Cable

Camera

PoC Video Decoder Module

Monitor

or

Television

Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

Camera

Main cable or

antenna

Coax Cable

PoC Video Decoder Module

Modulator

AMP

Amplifier

Splitter/

Combiner

Distribution

Panel

or Splitter

Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on

the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

To Next

Device

Television

Television

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-POCJBOX REV1005A