NetMedia NM-VIDBALL Specifications
NM-VIDBALL
Security Video Camera
Indoor Ball Camera
B/W Color
This general purpose security camera mounts to a typical rectangular junction box and is viewed with
a security monitor. To view the camera on a single standard television, use the TV’s composite RCA
Video Input jack.
Product Includes:
1. Camera Assembly (Camera, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base Plate, Video Connector, Power Connector).
2. 12V DC 300mA Power Transformer, Center Conductor Positive.
3. Mounting Screws.
Elbow Bracket
Adjusts camera angle at Base
Plate , screw, and Housing.
Locking Ring
Secures elbow bracket to
Base Plate at desired position.
Color
Camera Assembly
B/W camera Color camera Day/Night Color Housing
NM-VIDBALL-BW
Available in UV Paintable White
NM-VIDBALL-CW
NM-VIDBALL-HW
White
Housing Cap
Remove to adjust focus.
Day/Night
Base Plate
Supports power regulator and
Video/Power Connectors. Mount
to rectangular junction box.
Video Connector
Female BNC connector.
FEATURES
Excellent image quality
Tough billet aluminum housing
Internally routed cables
Mounts to standard electrical fixtures
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply
1 year limited warranty
Camera Lens
Comes prefocused from
factory but can be adjusted
by rotating in either direction.
Power Connector
12V DC 300mA, center positive.
SPECIFICATIONS B/W Color Day/Night Color
Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Output Connector:
Power Requirement:
Power Connector:
Housing Size:
Base Size:
Mounting Holes:
Weight:
3.6mm
1/3” CCD
350 lines
72˚ Horizontal
0.7 Lux F2.0
Yes
5.5mm OD, 2.1mm ID, center positive
3.7mm
1/4” CCD
470 lines
54˚ Horizontal
0.5 Lux F1.2
No
Female BNC, 75 Ohm
12V DC, 300mA
2.33“ dia.
4.5” long x 2.75” wide
3.25” centers
1 lb.
(subject to change without notice)
3.6mm
1/3” CCD
470 lines
72˚ Horizontal
0.3 Lux F1.2
Yes
NM-VIDBALLNM-VIDBALL
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
MAN-VIDBALL REV0703A
NM-VIDBALL
DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.
Installation Procedures:
1. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the camera’s Video
Connector. Adapters, such as BNC to F or RCA, may be used where appropriate.
2. Connect the 12V DC 300mA Power Transformer from an AC outlet to the camera’s Power Input Connector.
3. Mount the base to the junction box (not included) and adjust the camera assembly for proper viewing. When
satisfied, secure all adjustment points.
Video Cable
Camera
Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In
jack and view through its video or line input. The picture will not be available on a channel.
Monitor
or
Television
Quad.
Sequencer
or
DVR
Camera
Monitor
or
Television
Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a
loopback or video output jack.
Distribution
Panel
or Splitter
Television
Television
Camera
Main cable or
antenna
Modulator
AMP
Amplifier
Splitter/
Combiner
Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on
the modulated channel. The modulator can also be the last piece of equipment in Figure 2.
To Next
Device
NM-VIDBALLNM-VIDBALL
NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 (520) 544-4567 Fax: (520) 544-0800 Email: sales@netmedia.com www.netmedia.com
MAN-VIDBALL REV0703A
Loading...