NetMedia NM-UTPBALL Specifications

NM-UTPBALL

UTP Security Camera

Indoor Ball Camera

B/W Color

This general purpose surveillance camera utilizes a built-on NetMedia UTP Video Encoder and external UTP Video Decoder
to exchange power and video across Unshielded Twisted Pair (UTP) cable, such as CAT5. There is no need to run multiple
cables to the camera location! It mounts to a typical rectangular junction box and is viewed with a security monitor or
television. To view the camera on a single standard television, use the TV’s composite RCA Video Input jack.

Product Includes:

1. Camera Assembly (Camera, Housing, Housing Cap, Elbow Bracket,
Locking Ring, Base Plate, UTP Video Encoder, UTP Jack).

NetMedia UTP Video Decoder and 24V DC 200mA Power Transformer.

2.

3. Mounting Screws and RCA Video Cable.

UTP Video Encoder

Not shown - Built into camera, it
exchanges power and video with Decoder
for One Wire Video™ on UTP cable.

Locking Ring

Secures elbow bracket to Base
Plate at desired position.

Base Plate

Supports UTP Encoder and cable.
Mount to rectangular junction box.

Day/Night

Color

B/W camera Color camera Day/Night Color Housing

NM-UTPBALL-BW

Available in UV Paintable White

NM-UTPBALL-CW

Female RJ-45 connector transmits

both power and video across CAT5

Camera Assembly

NM-UTPBALL-HW

Elbow Bracket

Adjusts camera angle at base,

screw, and housing.

Housing Cap

Remove to adjust focus.

Camera Lens

Factory set - rotates in either

direction to adjust focus.

and other UTP cable types.

White

UTP Jack

NM-UTPBALL

UTP Jack

Connects to Camera UTP
Jack via straight-through
wired UTP cable (T-568A).

Power Input

Connects to 24V DC wall
transformer (included)
and AC outlet.

FEATURES

UTP Video Encoder built into camera

Includes UTP Video Decoder module

One Wire Video™ Installation

Uses one inexpensive UTP cable

Supports up to 1000 ft of UTP cable

Supports industry standard wiring schemes

Excellent image quality

Tough billet aluminum housing

Internally routed cables

Mounts to standard electrical fixtures

Works in low light conditions

Adjustable camera angles

Tamper resistant wiring

Includes power supply

1 year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

UTP Video Decoder

SPECIFICATIONS

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Camera/Decoder Cable Connector:
Camera/Decoder Cable Type:
Camera/Decoder Cable Distance Range:
Camera/Decoder Video Signal:
UTP Decoder Video Output:
UTP Decoder Video Output Connector:
UTP Decoder Power Input:
UTP Decoder Power Connector:
UTP Decoder Size:
UTP Decoder Weight:
Housing Size:
Base Size:
Base Mounting Holes:
Assembly Weight:

Red LED

Indicates Power.

RCA Video Out

Connects to viewing
device such as monitor,
DVR, TV, or modulator.

B/W Color Day/Night Color

3.6mm
1/3” CCD
350 lines

72˚ Horizontal

0.7 Lux F2.0
Yes

5.5mm OD, 2.1mm ID, center positive

3.2” long, 2.2” wide, 0.9” thick

3.7mm

1/4” CCD

470 lines

54˚ Horizontal

0.5 Lux F1.2
No

Female RJ-45 jack

UTP: CAT5 or better

Up to 1000’
Proprietary

Composite

Female RCA

24V DC, 200mA

3 oz.

2.33” dia.

4.5“ long, 2.75” wide

3.25” centers
14 oz.

(subject to change without notice)

3.6mm
1/3” CCD
470 lines

72˚ Horizontal

0.3 Lux F1.2
Yes

MAN-UTPBALL REV0703A

NM-UTPBALL

DO NOT CUT OR SPLICE THE CAMERA’S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Connect a UTP cable (CAT5 or better) to the UTP jacks of the camera and Video Decoder. Each camera/decoder pair
needs a dedicated point-to-point wiring circuit. If attaching your own plugs, wire them for straight-through connec­tions: pin1 to pin1, pin2 to pin2; pin3 to pin3, etc. For standardization, you should also follow the T-568A color specifi­cation but it will not affect the camera’s function. Do not connect the UTP cable to computer networks or other

UTP video systems! Doing so could damage this product and/or the other attached devices!

2. Connect a video cable from the viewing device (monitor, Quad, DVR, modulator, etc.) to the Decoder’s RCA Video Out
jack. Simple adapters, such as RCA to BNC, may be used where appropriate.

3. Connect the 24V DC 200mA Power Transformer from an AC outlet to the Decoder’s Power Input Connector.

4. Mount the camera base to the junction box (not included) and adjust the camera assembly for proper viewing. When
satisfied, secure all adjustment points.

Up to 1000 Feet

Video CableUTP Cable

Camera

UTP Video Decoder Module

Figure 1 - Connecting the camera to a security monitor or standard television. Use the TV’s composite RCA Video In

jack and view through its video or line input. The picture will not be available on a channel.

Monitor

or

Television

NM-UTPBALL

Quad.

Sequencer

or

DVR

UTP Cable

Camera

UTP Video Decoder Module

Monitor

or

Television

Figure 2 - Connecting the camera to multiple pieces of video equipment. Every piece except the last must have a

loopback or video output jack.

Camera

Main cable or

antenna

UTP Cable

UTP Video Decoder Module

Modulator

AMP

Amplifier

Splitter/

Combiner

Distribution

Panel

or Splitter

Television

Television

Figure 3 - Connecting the camera to a modulator for whole house distribution and standard television viewing on

the modulated channel. The modulator can also be the last piece of equipment in Figure 2.

To Next

Device

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-UTPBALL REV0703A