NetMedia NM-MODEYE Specifications

NM-MODEYE

Modulated Camera

Indoor Low Profile Eyeball

B/W Color

The NetMedia MODEYE is a self contained camera and modulator that converts the video signal to a selected television
channel. It is powered over the same coax cable that returns the video broadcast signal for One Wire Video™ installation. It
mounts in a round 2.7 inch diameter hole and is viewed with a television tuner. Equipment that does not have a tuner, such
as a security monitor, Quad display, or DVR, will require a demodulator (any TV tuner device with a composite video output
such as a VCR) to convert the video for its use.

Product Includes:

1. Camera Assembly (Camera Eyeball, Modulator, Interior Base, Exterior Ring, Mounting
Ring, Video/Power Connector).

2.

Power Injector and 12V DC 300mA Power Transformer (Center Conductor Positive).

3. Mounting hardware (Mounting Screws, Grounding Strap, Grounding Screw).

Camera Assembly

Available in choice of colors:

B/W camera Color camera Day/Night Color Housing

NM-MODEYE-BW
NM-MODEYE-BN

Interior Base

Installs in round

2.7” dia. x 2.5” deep hole.

NM-MODEYE-CW
NM-MODEYE-CN

NM-MODEYE-HW
NM-MODEYE-HN

White
Nickel

Color

Camera Eyeball

Adjust for desired

field of view

Modulator

Not Shown - Switch

bank sets output channel:

UHF 14-69

CABLE 70-94, 100-125.

Day/Night

NM-MODEYE

Mounting Ring

Not Shown - Secures internal
base to mounting surface.

by rotating in either direction.

Camera Lens

Comes prefocused from

factory but can be adjusted

Exterior Ring

Video/Power Connector

Power and video share one coax
through female F connector.

FEATURES

Camera and modulator in one assembly
One Wire Video™ installation
Combines with existing TV channels
Viewable on multiple televisions
Excellent image quality
Tough billet aluminum housing
Internally routed cables
Mounts directly to walls and ceilings
Works in low light conditions
Adjustable camera angles
Tamper resistant wiring
Includes power supply and power injector
1 year limited warranty

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

CAMERA BACK

SPECIFICATIONS B/W Color Day/Nght Color

Camera Lens:
Image Sensor:
Resolution:
Field of View:
Min Illumination:
Infrared Sensitivity:
Modulation Method:
Output Channel:
Output Level:
Output Connector:
Cable Type:
Power Requirement:
Power Connector:
Assembly Size:
Exterior Size:
Hole Size:
Mounting Holes:
Weight:

3.6mm
1/3” CCD
350 lines

72˚ Horizontal

0.7 Lux F2.0
Yes

UHF 14-69, CABLE 70-94, 100-125

5.5mm OD, 2.1mm ID, center positive

1/4” CCD
470 lines

54˚ Horizontal

0.5 Lux F1.2

Digital Crystal PLL

+30dBmV

Female F, 75 Ohm

RG59, RG6 or better

12V DC, 300mA

4.6” dia. x 3” long

4.6” dia. x 1.5“ high

2.65” dia. x 2.5“ deep

3.5” centers

Covers mounting ring

and secures camera

eyeball position.

3.7mm
1/3” CCD
470 lines

72˚ Horizontal

0.3 Lux F1.2

No

1 lb.

(subject to change without notice)

MAN-MODEYE REV0704A

3.6mm

Yes

NM-MODEYE

DO NOT CUT OR SPLICE THE CAMERA’S CABLE. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY.

Installation Procedures:

1. Unscrew the Exterior Ring and remove the Camera Eyeball from the camera assembly. Locate the Modulator switch bank
and set the channel as shown in Figure 1. Choose an unused channel that matches the tuning mode of the televisions.
With antenna tuning, choose a UHF channel from 14-69. With cable tuning, choose a CABLE channel from 70-94 or 100-

125. There must be at least one blank channel on either side of the modulated channel to separate it from any other
broadcast, cable, or modulated source. When combining with cable service, be aware that digital data typically interferes
with channels 80-117, even when not subscribed to digital services. Channels 120-125 often work without any filtering.

2. Connect a coax from the camera’s Video/Power connector to the “MOD” side of the Power Injector. Connect the “TV” side
of the Power Injector to the grounded coax from a television or distribution system. Connect the 12V DC 300mA power
supply to an AC outlet and the Power Injector. The camera picture is now available on the programmed TV channel.

3. Insert the Interior Base through the 2.65” hole of the mounting surface and fasten with the Mounting Ring. Adjust the
Camera Eyeball for proper viewing and tighten the Exterior Ring.

ON

OFF

CABLE Channel 125

80 40 20 10 8 4 2 1

Add the numbers

printed on the

circuit board.

ON

OFF

80 40 20 10 8 4 2 1

UHF Channel 25

Figure 1 - Setting the modulated channel with the switches. Valid channels are UHF 14-69, CABLE 70-94, 100-125.

Distribution

Panel

or Splitter

Camera

Main cable or

Antenna

Power Injector

Optional Ch. 70-80 Filter (NM-CNF7080)

when there are no clear cable channels.

Splitter/

Combiner

Figure 2 - Connecting the camera to an antenna or cable service and distributing to multiple televisions.

NM-MODEYE

Television

Television

Sat In

Camera

Dual LNB

Satellite

Power Injector

Satellite
Multiswitch
w/Ant input

Satellite
Diplexer

Ant In

Figure 3 - Connecting the camera to a satellite system and distributing to multiple televisions.

NetMedia, Inc., 10940 N. Stallard Place, Tucson, Arizona 85737 [phone] Fax: [phone] Email: [e-mail] www.netmedia.com

MAN-MODEYE REV0704A

Satellite Receiver

Television